Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

Kilns

Posts

Kilns

#1

Jack Guzman from Maine

Kilns

Jack Guzman from Maine

I noticed several different mentions of kilns in this forum. I'm assuming that such an item is fairly common for turners.I use mine for drying chair parts as I usually work with green wood.

For those with a kiln,what is your's like? Mine I built under a bench.The side walls and back are 1" foil backed foam board. The bottom has a set of 3 ceramic bulb holders with 250w bulbs with a screen over it to keep debris off the hot bulbs.Temperature is controlled with a thermostatic switch.I cut a square hole in the bottom of one side and a similar hole in the top of the other side.I put a computer fan operated by battery in the top hole set to draw air from inside the cabinet.It works great. So,what do you use?---Jack

Re: Kilns

#2

Re: Kilns *LINK*

Mike Brazeau

An article on mine is at the link below. Have a batch of cherry bowls that went in on July 17 that are almost done. I start with a low temperature with fan only and create very high humidity >90% and then gradually add heat from one light bulb. I am totally sold on it. Would like to experiment with an even smaller version for drying just one or two bowls or small batches of spindle wood. I guess I could start with a pan of water to build up humidity. Another experiment.


img

Drying kiln

Re: Kilns

#3

Re: Kilns

Dale Bonertz

Mine will most likely be an exception. It is 8' wide 7' tall and 3' deep (outside dimensions). I built it much like common house framing with R-13 insulation. Wrapped the inside with plastic and then sheathed it and sealed all joints with a high grade caulk. Primed and painted the inside to protect the plywood. The front is three fiberglass door panels with Q-lon weatherstripping around the perimeter. Where joints are between doors I used 1/8" thick one sided foam seal (tape on one side). To heat it I have a oven heating element mounted in an old metal computer box and set on a commercial thermastat. Three fans putting out around 350 cfm each stacked evenly spaced from floor to ceiling. The chamber these fans are in also house the dehumidifier. They blow down a tunnel that is floor to ceiling in the back of the kiln. The area for stacking blanks measures a little over 6' wide and 6' tall and about 26" deep. With out pre-planning it worked out perfect to hold a 24 x 72 x 72 inch metro shelving system. I have had as many as 165 blanks in it of various sizes but I still have not filled it completely full. We'll see on this batch whether I turned enough to fill it completely or not. So far after two loads it is performing better than expected.

Re: Kilns

#4

Re: Kilns

Don Stephan

With a small capacity kiln I'm wondering what the advantage might be. I've not had any fatal cracks since I returned to drying turned once bowls in paper grocery bags on the concrete floor. Measuring weight loss every other day on a kitchen scale, seems to take 2-3 weeks to end weight loss, without any electricity. Perhaps a benefit to a small scale kiln would be the ability to dry the wood beyond air drying? Here in Cincinnati I expect my air dried bowls to be around 12%, but they sand very well and haven't had any problem using equal parts mineral spirits, boiled linseed oil and P&L 38 varnish as a finish. No doubt the finished bowls will continue to lose some moisture in houses during the winter and summer.

Re: Kilns

#5

Re: Kilns

Greg Haugen

The advantage of a kiln is time. The general rule of thumb is 1" of wood per year for air drying. In my kiln, I can dry 30 bowls in 4 weeks. It's a 3/4 size upright freezer, with all of the mechanical components removed. There's a grid of 1/2" holes 5"-6" apart on the top and the floor with a light bulb in the center. No fans. Hot air rises and pushes out the top, while it pulls fresh air in the bottom. I've used this style of kiln since '08. The original instructions, attached below, came from Kelly Dunn of Hawaii.

Refigerator kiln,

Get an old fridge or standing freezer. Free for the taking at landfill

dropoffs and applience repair shops.

Take out all things not needed. On the fridge cut out or take out the

divider section between the fridge and freezer compartments.

Drill some half inch holes in the top and bottom roughly four inches

apart. Get an outlet box and a ceramic lightbulb holder. Put that in

the bottom center. If the plug in wire for the fridge is still good

you can use that. Make a metal cowling to go over the light bulb. This

is just in case so nothing can fall and break the bulb and cause a

spark. Often aluminum was taken out of the inbetween section that is

perfect for a cowling.

The shelving, use ones from fridges and freezers that fit your

unit,can be started right above the light.

Rough turn your pieces to about an inch thick.

Bowls must be coated on the outside with green wood sealer to prevent

from cracking.Pen blanks and small items up to you.

Stack on the bowl sides leaving a very small space for air to travel

in the bowl. And fill the thing up. If you are not in a hurry a 40

watt light bulb can be used and as pieces dry pull them out and rotate

work from the top of the kiln to the bottom. No fan is needed with

this kiln. An air convection current will be created and will work for

you 24/7.

You will need a moisture meter. Even a cheap one will work for this.

Start with a 40 watt bulb. When the bowls are around 14 to 16 %

moisture pop in a 60 watt bulb. With the 40 watt bulb moisture will

drip from this thing. You can leave it or wipe it dry. That will all

be gone by the time you put in your 60 watt bulb. which should four

weeks or under for sopping wet bowls. In about a week the bowls should

be about 12% or less. Pop in a 75 watt bulb. It should be under a week

and the work will be 6 to 8%.If your kiln is in a cold area you may to

go up a 100 watt bulb to do the job. Turn it off and let it cool down

before removing the bowls. If a sixty or 75 watt bulb burns out before

the load is finished and the bowls are cold start with the 40 watt for

a day then move it back up one day at a time to not shock the wood.

When loading the kiln put your most stable woods the closest to the

heat. the bowls near the light will be finished before the ones near

the top are.If you want to pull out hot finished work from the bottom

wrap them in a towel so they cool slower.

This draft written 10-12-2008 and will be upgraded as needed.

I have been using these kilns for 20 years now.

Re: Kilns

#6

Re: Kilns

Dale Bonertz

30 bowls in 40 weeks!! Just as well air dry them. :) :D

Re: Kilns

#7

Sorry Dale, typo.  Four weeks.


Re: Kilns

#8

I knew that... just funny NM