Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

outboard spindle buggered threads

Posts

outboard spindle buggered threads

#1

outboard spindle buggered threads

dick gerard

Here is a photo of the outboard spindle of my circa 1982 General 260. The Oneway vacuum rotary adapter came loose and rattled around on the spindle before I was able to ut down the lathe. Of course, with a blank on the in board side, the spindle kept right on rotating. You can see the results. Compare the flattened top threads with the knife edge thread right next to the green headstock.

[URL=http://s89.photobucket.com/user/bowlman_2006/media/outboardBuggeredThreads_zps82359253.jpg.html][/URL]

So I'm screwed right? Option 1: take the headstock apart (an all day job) take the spindle to a machinist and have them restore the 1 1/8 x 8 left hand threads. Big $$$$ ... or

Option 2: take the spindle out, order a new one from General Interational, and hope that 1) it fits and 2) thy still make that particular spindle ... bigger bucks... or

Option 3: Buy a new American Beauty (good reason to buy one right) even bigger $$$$

Option 4: find a way to do it myself. can I find a tap and die large enough to do it and do it with the spindle in place? Maybe I had a hardened left hand nut I could thread it on and restore the threads.

But wait a minute! I DO have a left hand nut ... its called the hand wheel. And yes, it is harder than the spindle. So, find the handwheel (20 minutes of searching) use my extra large channel locks, and several minutes later, all the threads are now knife edged once again. damn, I'm just brilliant today. Tomorrow is Tuesday ... that's my day to be a dumb***.

Re: outboard spindle buggered threads

#2

Re: outboard spindle buggered threads

Peter Lamb

You be very clever. So now are you going to tell us how you messed it up in the first place?

Good to see you briefly in Tampa

Re: outboard spindle buggered threads

#3

Rob Wallace

Nice recovery Dick!

Rob Wallace

I am happy you found a clever solution! (Finding a LH 1.125 x 8 die would not be easy or cheap!) It IS a bit disconcerting that the spindle metal is softer than the handwheel nut, but in this case it was a saving situation! Glad to know that you are back in business.

As a new owner of a Robust American Beauty, I can tell you that I hope someday to welcome you to the club so we can don our smoking jackets, ascots, brandy snifters, and fine Cuban cigars and talk about our lives at the lathe before we got our Robust.... :D

Seriously (no pun intended!!), keep the Robust dream alive!! - It took me several years to get into the financial position that I could give Brent the "Throttle-up!" from ground control and build mine. I am extremely happy with my AB, and you would be too!

Good to see you at the Symposium!

Turn safely!

Rob

Re: outboard spindle buggered threads

#4

Harry Robinette

Re: outboard spindle buggered threads

Harry Robinette

Dick I keep a thread file for 1-8 and 1 1/4 -8 in the shop all the time.I makes it very easy to keep the threads dressed all the time or to fix an ooops.

I got mine from a friend but I believe Graingers has them also.

Re: outboard spindle buggered threads

#5

Re: outboard spindle buggered threads

Pete in Holland, MI

I would try the thread file first.

Skip the theading die. If not used absolutely perfect, you can shift the centerline of the threads away from the centerline of the shaft, then you have a problem.

If the file fails, remove the shaft and find someone good with his metal lathe and have him set up & chase the threads with a single point tool. I've done this numerous times on old machine parts.

Your threads are not lost as they are. It is critical that they are not mashed out of their proper profile so they dig into the threads of mating attachments. It is critical that the shoulder that is present is clean & true though.

Good luck !

Pete

Re: outboard spindle buggered threads

#6

George Taylor

Slightly mangled spindle on PM3520

George Taylor

What file or die do I need to redress the front end of the spindle on my 3520B? Is it fairly straight forward or do I risk really screwing things up? The back end of the spindle lines up and seats well just mangled the front end it only seems to affect the chuck when I start threading it on.

Thanks

PS chuck got stuck against tool rest while spinning ... scared the be-jesus out of me. Was being lazy letting the lathe unscrew the chuck. I know - DUMB!

Re: outboard spindle buggered threads

#7

George, you can unmangle the.....

JamieDonaldson

...threads to some degree with a triangle file if done carefully, which will reduce potential damage to your chuck threads. If its not too bad, just leave it alone! ;)

Re: outboard spindle buggered threads

#8

Re: George, you can unmangle the.....

John Lucas

Ditto what Jamie said. Just turn it on in reverse and run is slow. The slide the triangular file in and run it out a few times checking the fit of your chuck often.