Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

" I's had enough and enough is too much!" *LINK*

Posts

" I's had enough and enough is too much!" *LINK*

#1

" I's had enough and enough is too much!" *LINK*

robo hippy

Reed is off fishing for a week and wanted this posted for safety reasons

http://youtu.be/F4qIM_-Jzgk


http://youtu.be/F4qIM_-Jzgk

Re: " I's had enough and enough is too much!" *LINK*

#2

Good video, and important!

GaryG in MD

Thanks robo.

We have needed this.

You'll never know it, but you may have just saved someone's life.

...GG

Re: " I's had enough and enough is too much!" *LINK*

#3

Steven Antonucci

amen


Re: " I's had enough and enough is too much!" *LINK*

#4

I added a link from my website.

George Guadiane

This was an excellent piece and I'm sure it will save life and limb over time.

My only additional thought would be to run your blank up to a speed as high or higher than you would normally turn to check the integrity of the blank (WHILE OUT OF THE LINE OF FIRE) before even starting to turn.

Re: " I's had enough and enough is too much!" *LINK*

#5

action

GaryG in MD

As self-proclaimed and defacto Safety Officer of Montgomery County Woodturners, I just emailed the link to this video to all our members and strongly recommended that they view it and take it to heart. I'm already getting positive responses.

If one person from each of the other 300+ AAW Chapters does the same thing, we will have covered around 15,000 people. Robo has done us a service in preparing this video. Let's get it out there for him, and for us.

...GG

Re: " I's had enough and enough is too much!" *LINK*

#6

Re: action

Dale Gillaspy

Coming from someone who has been in the Safety and Risk Management field for 18 years, I have a problem with someone putting out a safety video and proclaiming he doesn't need the same gear he is preaching about because he is a professional, and beginners should wear the masks.

Several times during the video he was not standing "outside of the line of fire", and that is not the only deciding factor in an accident. I have had pieces come off the lathe and bounce all directions. I counted at least twice where the tool came in contact with the wood before it was on the tool rest.

Not only that, but one of the most common problems is flying debris in the eyes, and Reed was wearing prescription glasses, not safety glasses.

This is coming from someone who has a lot of respect for Reed and admires a lot of what he has done in the woodturning community, but I can't give any credence to this video under those conditions. Sorry Reed.

Re: " I's had enough and enough is too much!" *LINK*

#7

Re: action

Dale Bonertz

I have to agree with Mr. Gillaspy. Sorry Reed but if you are going to make a safety video then show safety. It is not enough to say beginners should do this or that and your phrase of "Do not attempt this, professional driver on closed course" really does not cut it. I respect the many things you have contributed but there are way to many violations of safety in this video to give it credence. There are many good points in it but a safety video needs to be clean of safety violations.

Re: " I's had enough and enough is too much!" *LINK*

#8

Steven Antonucci

Ferrari red or Corvette red?

steven antonucci

It's the first video I've seen that talks about the line of fire? Is it perfect? Probably not, but it is a start.

Re: " I's had enough and enough is too much!" *LINK*

#9

I agree

Dale Bonertz

It is a good start, just not ready for release.

I'll have the corvette red please. :)

Re: " I's had enough and enough is too much!" *LINK*

#10

Steven Antonucci

On my way over... 


Re: " I's had enough and enough is too much!" *LINK*

#11

Re: " I's had enough and enough is too much!"

robo hippy

Well, a couple of things.

First, I had to keep the camera man out of the line of fire as well, and it may look like my head is in line some times but that is the camera angle. At no time when turning does my head come into that line.

I reviewed the video, and can't find any time when the tool comes into contact with the wood before it is resting on the tool rest. The resulting slam would be a good indicator, and there are none that I could find.

We all have bad habits that are not for beginners, and from habit we may present them when demonstrating. While you may not like all of my video clip, and it was done in a hurry, are you now going to approach your bowl turning demonstrations differently? Is standing out of the line of fire going to become standard 'safety' instruction? That is the point I was making and the change I want to see.

robo hippy

Re: " I's had enough and enough is too much!" *LINK*

#12

Steven Antonucci

Not only do I do it, I discuss it

steven antonucci

Every demo comes with a physics lesson...like it or not.

Steve

Re: " I's had enough and enough is too much!" *LINK*

#13

May the luck be with you

walta

May the luck be with you because that is what keeping you alive! If you look at the part of the blank that came off the lathe at 4:07 the fault in the blank is very dark and should have been obvious.

The most important safety rule is don’t turn wood with known defects. I recall of the major accidents the turner sought out flawed wood and still can’t understand why superglue and the packing tape wrap around the wood did not keep it together and away from their head.

It is no wonder the gouges give you so much trouble as there is no way you can see what it is doing from where you are standing.

I admit my face shield is only used while ruffling out and I don’t expect it will stop anything that weighs more than 8 ounces.

Walta

Re: " I's had enough and enough is too much!" *LINK*

#14

Jesper, Denmark

Re: " I's had enough and enough is too much!"

Jesper, Denmark

Despite the lack of add-on safety equipment, such as faceshields, helmets and full body armor, this video presents a significant idea of basic safety, which should be understood and adopted by all.

The most important safety gear is using the inside of your head. Standing away from the "line of fire" is such a simple and basic idea which applies not just to the lathe, but even more importantly to such tools as the table saw etc.

Thinking about and understanding where the projectiles might fly is THE primary safety idea. All the add-ons are secondary - and maybe not very useful when the big chunks start flying around the shop.

Please do not conclude that I am advocating not using add-on safety equipment - even if you do wear a helmet, faceshield or other stuff, staying away from where the chunks fly is still the important part.

Re: " I's had enough and enough is too much!" *LINK*

#15

Re: " I's had enough and enough is too much!"

Stuart Johnson

A good demonstration on the "line of fire". Some shots were hard to follow and looked like he was still in the line but he did explain that his head was out of the line. I agree the lack of safety gear might prevent the video from being an all around safety demonstration but it did show what was intended.

Re: " I's had enough and enough is too much!" *LINK*

#16

Re: " I's had enough and enough is too much!"

Dale Gillaspy

To see pictures, go to the AAW website, or if you are on FB, go to the AAW page. The highlight of my trip is really hard to nail down. There was only 1 of the demos I went to that I could have missed, the others were all great, even if I only picked out a thing or 2. I came away with some great pieces, including a Molly Winton, David Marks, and David Hogbin.

Helping in the youth room was more fun than I could have imagined. I'd consider going just to do that.

Just putting faces with some of the people you meet online was fantastic. I can't really narrow it down more than that. If I had to pick a favorite demo it was probably Nick Agar or Art Liestman, they were great, but hilarous!

Re: " I's had enough and enough is too much!" *LINK*

#17

Re: I agree

robo hippy

Like just about every thing, I would do a lot of the filming different, but getting the point made was most important.

Oh yea, I want a 56 T Bird!

robo hippy

Re: " I's had enough and enough is too much!" *LINK*

#18

Re: Good video, and important!

Ray Carson, Lawrenceville, NJ

Good videos !! Thanks for sharing.

Re: " I's had enough and enough is too much!" *LINK*

#19

Alan Zenreich

Re: " I's had enough and enough is too much!"

Alan Zenreich

Reed,

Keep in mind that those 'professional drivers on a closed course' all wear full face helmets and complete protective gear...

Just sayin' < vbg >