Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

Buffing with Tripoli before flocking?

Posts

Buffing with Tripoli before flocking?

#1

Buffing with Tripoli before flocking?

Craig Daymon

I have my niece's jewelry box with about 5 coats of Waterlox on it now. I want to buff it out with Tripoli and I'd like to do that inside as close to, if not including, the point where I plan to cover it with flocking material.

Anybody who has worked with flocking before know if buffing with Tripoli will impact the adhesive?

Just don't want to mess it up this close to the finish line.

Thanks,

Craig

Re: Buffing with Tripoli before flocking?

#2

Re: Buffing with Tripoli before flocking?

Dick Coers

I assume you will be using a bar of tripoli to charge the buffing wheel? If so, wax is what the bar is made from. If you had to buff where the flocking will go, I would wash it with mineral spirits to remove the wax. Why not sand with 600 grit where the flocking will go to level the finish? Don't know why you would buff that surface.

Re: Buffing with Tripoli before flocking?

#3

Re: Buffing with Tripoli before flocking?

ken ward

I make a lot of jewelry boxes and flock some of them,all I do is finish them with 320 and make sure I don't get any wax,oil on the inside,before flocking and I have never had the flocking come off.

Re: Buffing with Tripoli before flocking?

#4

Re: Buffing with Tripoli before flocking?

Don Evans

You don't want to buff where you are going to be putting the glue. Pick a transition point, like the 90 deg edge at top of inside and tape it off. Ever seen a taping job on a car paint job? Sand the inside (actually I would not have put waterlox or any finish on area to flock as the glue will seal it) The sanding will give the glue tooth to hold on too.

The tape will keep glue off the non flock area.

Don

Re: Buffing with Tripoli before flocking?

#5

Re: Buffing with Tripoli before flocking?

Al Goldstein

On the bottle of glue to be put down before the flocking it says to seal the surface with shellac. The shellac went on unevenly so it seems it is used as a surface coat to prevent the glue from being absorbed in the wood. Just my experience.

Re: Buffing with Tripoli before flocking?

#6

Re: Buffing with Tripoli before flocking?

ken ward

When I 1st used it,I tried the shellac and the finished drawer looked like crap,had avery uneven finish when done,so now I just finish with 320 and

make sure all dust is gone and it has been coming out real nice.

Re: Buffing with Tripoli before flocking?

#7

Some follow up

Craig Daymon

I want to buff the box, but there is no reason to buff the inside where the flocking will be. The issue is that I created the box with an inset lid and wanted to buff up to the point where the flocking would be applied. I was thinking more about any areas at the transition that would inadvertently get buffed. I guess I can do the outside as I normally would and maybe use a Dremel with a buffing wheel to do the inside area up to the point where the flocking will be applied?

I finished the inside since the flocking instructions indicated that it should be sealed. Probably should have wet sanded the first coat inside to fill the pores, though there's enough finish in there to make it pretty smooth. I'm giving it plenty of air time to dry. The instructions indicate that a smooth surface will give better results.

Thanks,

Craig

P.S. I used carbon paper to mark where the lettering/dedication would go on the inside. I hope the font I used is fancy enough. I received a request that the font be fancy. I'll get some pictures up when it's done.

Re: Buffing with Tripoli before flocking?

#8

Re: Some follow up

Don Evans

Why not just sand the flock area then seal with watered down version of the glue, when it's dry, sand smooth, then put on more glue and flock. Using a foam brush to apply the glue may be easier to get a smoother glue surface for the flocking.

Don