Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

General's Upgrade

Posts

General's Upgrade

#1

Harry Robinette

General's Upgrade

Harry Robinette



Well the new 2hp 3ph VFD and Motor are installed and running but still have a problem with the old reeves drive pulley it keeps making a knocking sound.

I'm going to call General the first of the week.

Hope these picture come out ok.

Re: General's Upgrade

#2

Re:  General's Upgrade

Jim Lang

A question. I notice that you are using a link belt with your Reeves drive. I was told they did not work well with the split pulleys. Comments?

Re: General's Upgrade

#3

Re:  General's Upgrade

Bill Howatt

I used a link belt on a cheap lathe similar in size and construction to a Jet1236. Its Reeves drive was not as sophisticated as the General's and it worked fine.

Bill

Re: General's Upgrade

#4

Harry Robinette

Re:  General's Upgrade

Harry Robinette

Jim

So far no trouble, I had the link belt on the lower motor to reeves drive and regular on the upper end with the old drive so I only changed the top belt. The problem with the pulleys is a knocking sound in the 3 way drive pulley set.

Re: General's Upgrade

#5

Keith Tompkins

Re:  General's Upgrade

Keith Tompkins

Hi Harry, with the new variable speed motor, why not eliminate the reeves drive altogether? It should be an easy fix (?)

Re: General's Upgrade

#6

Harry Robinette

Re:  General's Upgrade

Harry Robinette

Keith

It's not really easy and I think it's going to cost to much. I'm trying to get a hold of

General but have to wait tell tomorrow.The trouble is even with a set of step pulleys I'll need to have a way to detention the motor to change pulleys and I believe General's going to want some big bucks for that detentioner. I guess I'll find out tomorrow.

Re: General's Upgrade

#7

Keith Tompkins

Re:  General's Upgrade

Keith Tompkins

Hi Harry.....I didn't realize there were so many differences....If you don't mind, how much was the movable/remote switch. I need that for my lathe!

Re: General's Upgrade

#8

Harry Robinette

Re:  General's Upgrade

Harry Robinette

Keith

The stop switch is a 220v,3ph from Ebay that's $8.82.I ran a 12 gauge 3wire in and then back out to the motor I do NOT shut down the inverter with it.If you need the site for it drop me a line.

I turned the button on the lathe for the stop then screwed and glued it to the switch. two magnets on the back with epoxy and bang emerg stop.

If I ever get the upgrade done I'm going to try to put everything on the forum.

Re: General's Upgrade

#9

Leo Cuellar

Re:  General's Upgrade

Leo Cuellar

Hi Harry. A couple of thoughts come to mind. Perhaps there are a link or two on the link belt that are narrower or wider than the majority that are causing the pulley to widen or tighten in spots? Also, I had one that knocked because of a barely perceptible crack on one of the pulley faces.

Also, are you using the lever on the Reeves to adjust speed as well as the VFD? If not, does the speed range work well with just the VFD? If so, you would only need to replace with a single pulley instead of a stepped one.

Re: General's Upgrade

#10

Re:  General's Upgrade

Bill Howatt

Most VFD lathes, perhaps the DVR is the exception, have at least 2 speed ranges to keep the torque up in the motor. The higher speed also allows the fan in TEFC motors to blow more air.

The General with factory VFD has 4 speed ranges but having 4 instead of 2 or 3 is probably so they can just use the spindle and pulleys from their 4 speed basic model.

If you aren't roughing large, wet, out-of-balance bowl blanks where a slow speed with good torque is needed then having only a single range would likely work fine.

Bill

Re: General's Upgrade

#11

Harry Robinette

Re:  General's Upgrade

Harry Robinette

Leo,Bill

Thanks for the info.

Leo; I'm going to try to move the outside sheaves in a little and this should tighten the center sheave a little( the center sheave is moving and making the knocking noise) I believe this will work.If not I'll pull the reeves drive and check it out for cracks burrs dent ect.

Bill; the pulley for the 4 step from General is $148.00 + shipping I called this morning. I can find step pulleys that will work then I have to get something rigged to adjust the motor to move the belt. Right now with the reeves drive I can run from about 60 to 2400 rpm. I think this will be ok for a speed range IF I can get the knocking and fine vibration out of the reeves pulleys.