Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Price drop on over 1300 Rockler items

New (and I do mean new) Shop

Posts

New (and I do mean new) Shop

#1

New (and I do mean new) Shop

Jim Rutten

We recently had a post frame building put up and one wing of it is reserved for my retirement shop (right now it feels like it will never get here). It has a couple of windows and has been more insulated then the rest of the building. Right now it is a blank slate and we don't even have electricity run to it yet (although it has been roughed out for it). For those of you who have been here before what suggestions do you have for me. We have been discussing lighting and electrical outlets and more is always better for both. Anything in the short range to look out for or in the long range? It is totally lockable which I really like. Experience is the best teacher so I am hoping some of you will share your experiences both good and bad.

Re: New (and I do mean new) Shop

#2

Mike Stafford

Re: New (and I do mean new) Shop

Mike Stafford

Jim, you said you have already roughed out for electricity. One of the few good things that I did when I built my shop was to put outlets in the ceiling which enabled me to plug stuff in there and not have the cords strung all over the shop. I also recommend putting in more outlets than you can imagine using and placing them at a height above any future cabinets, work benches etc.

Plan a location for your compressor if you have one so that it is in a relatively dust free environment and also reduces the sound you must be subjected to. The sound isolation goes for the dust collector as well.

And lastly provide for dust collection. I don't have good dust collection and I wish I did. Having good dust collection will in the long run save you loads of clean up time but more importantly it will save your lungs.

Installing a shower bar or rails on the ceiling where you can hang shower curtains will also help you contain the chips and make clean up easier.

Since I made so many mistakes when I hurriedly built my shop I know there are lots of folks out there with additional good ideas.

Re: New (and I do mean new) Shop

#3

Paul Kramer

Lots of outlets

Paul Kramer

The previous respondent had some excellent suggestions. I would add that I put a quad outlet on every other stud at 54" from the finished floor all the way around the room. I also put two quad outlets in the ceiling and one in the center of the floor. I also put a 220 in the center of the floor for the table saw, one in the adjacent garage for the dust collector, one outside for the compressor for the HVAC unit, and I would have put another one on the middle of each wall for the jointer and the enhanced bandsaw I acquired later on.

I don't think you can have too much lighting in a building with only two windows. Both general and task lighting are necessary. I don't know enough about it to educate others but I have learned several things about fluorescent tubes recently that I am sure others know better and can communicate better.

Lastly, I urge -- as much as possible -- build in flexibility for the future. It's hard to predict where things will be going but do your best to anticipate what may be the next 'thing' so it won't be much trouble to incorporate into the shop.

All the best of luck,

Paul

Re: New (and I do mean new) Shop

#4

Rob Wallace

Re: New (and I do mean new) Shop

Rob Wallace

Jim:

I invite you to read the series of 3 articles I wrote on 'Setting-up your Woodturning Workstation' for the AAW's electronic newsletter "Woodturning Fundamentals". All of these were sent to subscribers in 2012.

Part 1 - http://library.constantcontact.com/doc207/1103600789564/doc/3jTgF0ZFXEebNyya.pdf

Part 2 - http://library.constantcontact.com/doc207/1103600789564/doc/Gzgx91xbIfPcFa5Q.pdf

Part 3 - http://library.constantcontact.com/doc207/1103600789564/doc/r1vQD1ofHhs3RxQd.pdf

There are a range of things outlined in the articles for you to consider when setting-up your shop: i.e. "infrastructure" things like electrical supply, ambient and task lighting, dust collection, the position of and the arrangement of things around the lathe at the turning workstation, concepts of work envelopes and handedness, aspects of storage of tools and supplies, safety, and personal protection equipment.

I hope they help.

Rob Wallace

Re: New (and I do mean new) Shop

#5

Re: New (and I do mean new) Shop

robo hippy

My shop is 24 by 36. I had a 100 amp sub panel put in the shop, and think I could have used more (extra never hurts). Dedicated 220 by 20 amp circuits for lathe, compressor, dust collector, takes up most of that. I still need the slab out back for compressor and dust collector.

robo hippy

Re: New (and I do mean new) Shop

#6

Steven Antonucci

Good floor surface sweeps easier

steven antonucci

Everything on wheels (except lathe) so you can get it out of the way

4 outlet boxes cost $1 than 2 outlet boxes- you don't need to use all of them all of the time, but you can't use what you don't got.

If you have some height, put everything up high that you can. The less you have to sweep around, the easier and more likely you are to clean up.

Steve

Re: New (and I do mean new) Shop

#7

Harry Robinette

Re: Good floor surface sweeps easier

Harry Robinette

A quiet room for the DC to me was a must also the compressor. Put in an extra DC port in any long run you always need a port were there isn't one. Put french cleats all around the wall so you can move any cabinet anywhere.Put a light in all the corners on there own circuit if you blow the power you'll still have light.

Get a GOOD fire extinguisher at lest one and probably two. Put chip board up on one wall so you can hang things wherever you want.This really helps with the big or ill shaped stuff. Get a ambient air cleaner (have outlet put in ceiling.)

Just some of the things I did (and didn't do) when I set my shop up.

Oh Ya the big thing Have Fun!!!!!!!!

Re: New (and I do mean new) Shop

#8

Surface Mount Wall Outlets

charlie belden

You WILL relocate machines and benches - and probably get a new machine or two some day down the line. If all the wiring is IN the wall, moving outlets and switches can be a real hassle, But if it's in surface mounted conduit and all the boxes are surface mounted you can rearrange them - without having to open up walls - and patching them up aftewards. You WILL want to move a wall outlet or two a year of five from now.

Put a surface mounted breaker box IN the shop and run everything from there.

Go with quad boxes rather than duplex boxes. Four outlets are twice as good as two outlets.

Put the boxes at least 36" above the floor. They'll be above machines and bench tops and easy to get to - without having to climb under anything.

There's going to be a bit, or a lot, of fine sawdust. If there's a plug in an outlet dust can't get into the outlet. But if there isn't a plug in an outlet, dust CAN get into the outlet. Get those Kid Proof outlet plugs - and keep dust out of your outlets.

Every wall should have at least one 220 outlet.

Two our three ceiling outlets - the kind with the twist lock so power cords from them can't fall out - are handy. Lets you get a machine you need to get all the way around - without a power cord running acrossed your floor - to trip on.

Re: New (and I do mean new) Shop

#9

Re: New (and I do mean new) Shop

Barry Irby

I agree with all of the above. Here are a couple of stupid stuff suggestions.

If you haven't already, add a BIG door so you can get the really big stuff in and out. This includes the materials and the projects and also the machines. Really good to be able to drive to that door.

Also, figure out what you want to do in the shop and plan around that. Have a designated place for the project. I have seen a bunch of shops with no space left for a big project. A friend of mine builds kitchen cabinets for a living. His second shop has a space as big as a kitchen and he sets up the cabinets as they would be in the actual house. Even after thirty years it saves a lot of second guessing.

Think about the work flow through the shop. Haul in and store stock, Prep the stock, build the project and then move it out. This applies whether it is a flat work shop or a turning shop. Why haul it all the way through the shop to prep it and then have to haul the waste back out? Why have the storage in the way of getting the project out? Don't have cords and ducts hanging from the ceiling in an area where you want to turn long boards around int he prep process.

Re: New (and I do mean new) Shop

#10

barry rockwell

Re: New (and I do mean new) Shop

barry rockwell

Boy, what a great bunch of suggestions! The only thing I can add is to put white slot-board on all the walls that are not already covered with workbenches or something else. With all the accessories and hooks available for slot-board you can put shelves, tools, cabinets, etc. anywhere you want, and change it all around anytime you want. The white coating helps brighten up the shop.

Re: New (and I do mean new) Shop

#11

Couple of things

Jake D

I had a post frame shop at the last house. 32' x 40'. Things I learned:

Make sure you put a vapor barrier under the concrete slab, didnt do this and fought moisture every sling

Highly polished concrete is much easier to clean up.....but also very slippery with snow on your boots (mn winters)

Make all the outlets, and wiring 20amp. The cost is minimal upfront and you won't regret it

Use a shop planner, grizzly used to have one on their website. Don't forget about indeed and out feed space

A second on dust collection. The cyclone was one of the last things I bought, but should have been the first

Another second on ceiling outlets

Wire for a ceiling fan. It's nice in the summer and helps heat in the winter

Lots of lights. I used high out put cold start florescents, (q:12, 8'lights) Liked the light, despised the constant humm when on. Don't know what I will use on the next building. Also getting rid of the 8' bulbs was a pain.

200a service

Multiple 240v outlets on each wall. I converted all my 240 machines to have the same plug (as long as the amperage was ok). It allowed move flexibility. If you are buying bigger machines, they are all 240. I had 7 at the old shop.

Make it flexible, I changed layouts multiple times before settling on one I liked....and we moved 7 months later. ;-)

Most of all have fun and good luck.

Jake

Re: New (and I do mean new) Shop

#12

Mike Peace

French Cleats

Mike Peace

An inexpensive alternative to slot board is French Cleats. 3" wide strips of 3/4" plywood with top cut at 45 degrees. Put on every wall.

Re: New (and I do mean new) Shop

#13

Thanks for the suggestions everyone

Jim Rutten

You guys are awesome.