Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

New Drive and Motor

Posts

New Drive and Motor

#1

Harry Robinette

New Drive and Motor

Harry Robinette

Started a upgrade to my General 160-18. I have a DC drive 3/4hp which I thought was a 1hp.It's running throw the Reeves drive on my lathe which put's a slight vibration in the lathe from the moving pulley's. This new drive is a 220v 2hp 3ph Automation Direct VFD and 2hp motor. It will run direct from motor to spindle and I hope make a smoother and higher torque lathe.I'm going to try and give everyone a running record of cost and work to do this.I hope this will help others if they decide to do this.

Pricing:

VFD=$241.00

Motor=$166.00

Wire, Emeg sw box, connectors, plug=$44.00

Emeg switch= had this

So so far cost is $451.00

the pictures are the old drive and the one I'm putting in.

I hope everything I'm posting is OK.This is my first time to do anything like this on the forum.

Re: New Drive and Motor

#2

Pretty cool but print the photos larger.


Re: New Drive and Motor

#3

Re: New Drive and Motor

Josh Bowman

Harry, ditto on the pictures. So did you remove all the reeves drive guts and put a standard pulley on the shaft? A friend of mine has a Jet with reeves and we're watching your build to consider updating his.

Re: New Drive and Motor

#4

It's too bad

Bill Howatt

It's too bad that you aren't modifying a 4-speed 160 with the step pulleys. They probably used 4 ranges because they could use available hardware - 3 or even 2 would be workable.

For interest my 2HP VFD General 26020 lists the following on the panel relating speed to the 4 pulley's being used:

Range 25-625 RPM Low torque warning at: 175 RPM

30-1100 RPM 300

65-1780 RPM 475

125-2870 RPM 800

How low is low? Don't really know, and the importance depends on what you are trying to do such as turn an out-of-balance, large, wet bowl blank. Also, your VFD itself may provide a different torque curve. There is also something to be said for keeping the motor RPM up as much as possible, especially when loaded, so its fan can work better.

Bill

Re: New Drive and Motor

#5

Harry Robinette

Re: It's too bad

Harry Robinette

I had a lot of trouble trying to post the pictures for some reason so I made them small and then it work.I'll try again later.

I'm thinking of using the sheave that are there but lock them so they can't move side to side.Once I hook up the VFD I'll find the position they run best in and then lock them so they can't move side to side. If they aren't moving back a forth then the vibration should stop and they'll run just like a regular pulley. They way General makes there sheaves the center sheave moves between the two outside sheaves no springs, just the pressure from the belt being tightened on one side which loosens the other side. The whole three set of sheaves moves side to side which can be stopped by putting a clamping ring onto the shaft.

Now that I'm completely confused I'll stop and hopefully you'll all understand.

Re: New Drive and Motor

#6

Re: New Drive and Motor

Jake D

I'll be watching this with interest. I have a 260 and would love to put a vfd on it

Thanks for covering it thoroughly.

Jake

Re: New Drive and Motor

#7

Re: It's too bad

John Lucas

Harry Most of the modern lathes that have VFD's still use at least 2 pulleys to have a high and low speed range so you might want to make whatever locking mechanism you use some what reversible to be able to change to the optimum setting for at least 2 ranges.