Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Solar powered lathe?

Posts

Solar powered lathe?

#1

Solar powered lathe?

Devon Palmer

Greetings all,

I'm toying with the idea of creating a solar powered mini lathe for public demo's at craft shows, camping, etc. I'm considering a portable battery backed solar panel powering a small DC Permanent magnet motor w/ a Bonnie Klein lathe. I'd be totally happy turning small stuff when travelling.

Are her lathes as rare as they seem? I've been searching for months...

Re: Solar powered lathe?

#2

Re: Solar powered lathe?

Devon Palmer

Answered my own question: http://www.leevalley.com/US/wood/page.aspx?p=43104&cat=1,330,50260

Re: Solar powered lathe?

#3

Re: Solar powered lathe?

Tom

Woodcraft sells a mini lathe called Proxon. I have one at my summer lake home and use it for turning pens, bottle stoppers, tops, etc. when not fishing! It might work well on solar power.

Re: Solar powered lathe?

#4

Rob Wallace

Re: Solar powered lathe?

Rob Wallace

You re not likely to find a Bonnie Klein lathe - when she was out here for a demo a few years ago she told me (then) that they had not been produced or sold for several years, and were generally not available. Even her threading jig needed to be modified a bit for use on other mini-lathes. Those that own a BK lathe are probably going to hold on to them, even if only for keeping a piece of history. The Jet, Delta, and other similar mini's have fully replaced this lathe on the used market.

The keys to this solar powered system will be deep-cycle battery storage, a good array, and current & voltage limiters/regulators for charge and discharge cycles. Be sure your system has good blocking diodes in place. Post a picture or two of your solar/regulator/battery apparatus, and what kind of motor you select to drive the Taig "micro" lathe.

Good luck!

Rob

Re: Solar powered lathe?

#5

Re: Solar powered lathe?

Karen F.

I just got back from a 1 week camping / turning trip here in CA. I have a Delta midi lathe that we took and it worked out perfectly. We have a Honda EU 2000 generator that we plug into our trailer and while it was filling up our 2 batteries, I can turn anything (up to the 12" swing) on my 1 HP lathe. My husband does archery and while he was out shooting, I was turning and selling nearly everything I made. So it was pretty nice to have a beautiful area to look at while turning outside under the pop-up.

My friend takes her Jet Mini to Mexico and turns while overlooking the Pacific Ocean which is how I got hooked on the idea.

Re: Solar powered lathe?

#6

Re: Solar powered lathe?

Devon Palmer

Karen,

That sounds absolutely amazing.

Thanks for the advice everyone.

- Devon

Re: Solar powered lathe?

#7

Re: Solar powered lathe?

robo hippy

I would think that it would take a fairly big solar panel to keep a lathe running. You probably could use one to trickle charge a deep cycle battery, but probably not for much more than an hour or three.

robo hippy

Re: Solar powered lathe?

#8

Have you considered a treadle lathe?

Craig Daymon

Roy Underhill built one from discarded 2x material several years back. It had a large fly wheel that kept things spinning in one direction (unlike a pole lathe).

I suspect you could improve on his design just going with a few manufactured parts, better bearings, #2 MT sockets, etc., to make it a bit more precise and smooth running. Even with his design, it is very functional and capable of doing fairly large work. (Well, bigger than pens, tops and stoppers.)

The episode of, "The Woodwright's Shop", along with the issue of Popular Woodworking that detailed the project, should make it a very easy project. You don't have to build it with hand tools (unless you want) like Roy does.

It's on my LONG list of things to do.

I hunted down a few of the links. The Popular Woodworking issue was October of 2000. Here's the digital download of the issue.

http://www.shopwoodworking.com/digital-issue-popular-woodworking-october-2000

The episode of, "The Woodwright's Shop" that featured the treadle lathe was #1806. Unfortunately, that issue does not appear to be currently available. This is really odd, and seemingly short sited on the part of Popular Woodworking, since Popular Woodworking sells the show's videos. You would think that those featuring projects also appearing in their magazine would definitely be on the available list. Maybe contact Popular Woodworking and try to talk them into it? Here's the video page from Popular Woodworking.

http://shopclass.popularwoodworking.com/c-54-all-woodwrights-shop-channel-videos.aspx?viewall=1

-Craig

Re: Solar powered lathe?

#9

Re: Solar powered lathe?

Bob Salvetti

One of our guild members uses a 12 volt marine battery (DC) and inverter to power his Jet mini (110 volt AC) all day long when he does shows. Recharges the battery overnight. No generator noise.

Could you charge the battery via Solar panel ?

Re: Solar powered lathe?

#10

Re: Solar powered lathe?

Karl Brinkman

I have solar battery charger from Harbor Freight that charge a bank of deep cycle marine batteries. I have an inverter that I use in my shop. I need a generator to run my big lathe, tablesaw, jointer and planer,but Jet mini and every thing else is solar power.

Re: Solar powered lathe?

#11

Re: Have you considered a treadle lathe?

Ralph Lindberg

There are a number of good sources, there is a PDF (for free) you can down-load on how to build one.

Roy's book has instructions

There is a vendor on e-bay that sells kits

When I was working I went with option three. It's a great demo tool. I take it to club demo's to show people how it "used to be done"

But we also take a Jet or Carbtec mini and my Honda generator.

Re: Solar powered lathe?

#12

Re: Solar powered lathe?

Ralph Lindberg

The DW and I have talked about taking her Jet 1220vs. But even broke down it would take soo much room. I could get it into the forward bay, but I would have to work at it.

I have thought about a Carbtec, or other really small mini. There is a guy in the local club that just stores his in the basement of the rig.

Re: Solar powered lathe?

#13

Re: Have you considered a treadle lathe?

Craig Daymon

Is the one you built close to Ray's? Did you modify it in any way?

If/when I decide to build one, my plan was to use the bulk of Ray's design, with better bearings for the wheel, headstock, etc., steel angle iron to form the bed ways and assorted bits possibly borrowed from, or for, manufactured lathes.

My thinking would be to build a usable, quality lathe that is treadle powered. (Personally, I'd even like to consider borrowing from an old bicycle to allow gear changes, still with a fly wheel arrangement so I can power it with one foot...if possible)

Maybe it's even possible to power an old mini lathe via treadle? I know the JET is open below the pulleys. Detach the motor and put it on a frame with the treadle. Still need to draw tension on the belts.

Re: Solar powered lathe?

#14

Brad Vietje

YES!  With Details

Brad Vietje

Sorry to Chime in so late here...been doing taxes for a few days :~(

Since I operate a small solar installation company, and deal with these small battery-based systems daily, I'll be happy to help anyone who wants to run the numbers -- I won't try to sell you anything.

Simple answer is YES you can charge the battery/batteries with solar panels -- or another charging source if that works better for you. It all boils down to how much power your equipment needs, how long you want to run it, and how quickly you want/need to recharge it. The size of the inverter needed depends on the load, the size of the battery bank depends on how long you want to supply this power, the amount of solar needed depends on how fast you need to replace the power consumed.

Example: Here's one relevant example: my Nova Comet mini with a 1/2 hp motor, consumes about 350 watts. Add a pair of (LED) lights and some headroom, and we could call that 400 watts for a nice round number. Let's say I want to turn for 4 hours a day for a 3 day show; that comes to 12 hours at 400 watts, which comes to 4800 watt-hours, or 4.8 kWh.

Inverter: For a continuous load of ~400 watts, it would work best to have an inverter that can handle at least twice that much, to handle start-up surges. I'd go with a 1000 watt inverter, in this example. Then consider a pure sine wave vs a modified sine wave [sic] inverter (nobody would modify a true sine wave, so that's just a marketing gimmick -- it's really a modified square wave inverter). True sine inverters are MUCH better for anything that's variable speed, and will allow the motor to run more efficiently and run cooler (and use less battery power). For simple capacitor-start motors and most lights, a Pulse-width modulated "sorta-sine" inverter will work fine, and cost a lot less. For variable speed motors, spend the added funds, and get a real sine wave inverter. My Nova Comet has no variable speed, so I'd probably run with the less expensive inverter. A good value is a 1000 watt inverter/charger, which will automatically charge the batteries when plugged into grid power, even if no solar energy is available.

Batteries: If the battery bank needs to supply 4.8 kWh for 3 days (and assuming the worst case of no sunlight to help out), you'd ideally want to only use 50% of the battery capacity to deliver this, so you'd want a 9-10 kW battery bank (or re-think the 3 days of power part!). for a 12-volt system, that means you'd need about 400 Amp-hours of battery storage. That means using 4 big L-16H deep-cycle batteries (~130 pounds each!), which will cost some real money!

SO -- Let's forget 3 days of stored power, and shoot for a single, 4 hour day, instead! 4 Hours x 400 watts = 1600 watt-hours = 1.6 kWh, or 3.2 kWh if we limit the depth of discharge to roughly 50% (for much greater battery life). Using a 12-volt battery, that comes to 267 A-h. You could use 2 group 31 marine batteries in parallel, and since these are sometimes available as low-cost "blem's" this could be quite affordable (about $45 each, instead of roughly $100 - $125 each), (For the purists among us, marine batteries are not true deep-cycle batteries, but in their construction a compromise between car batteries and heavy-duty deep cycle batteries, but they will work OK -- they just won't deliver as much power, nor last as long as their heavy-duty deep-cycle cousins.) A group 31 battery is roughly 115 to 120 A-h at the 20-hour rate, so a pair of these in parallel would be about 230 A-h at 12 volts, so fairly close... you'd be discharging these about 60% instead of 50%, which they should handle quite well.

Solar charging: This will depend on how much sun is available -- also, winter sun vs summer sun if you want this system to work year-round... If you can set up outside where your solar panel(s) get full sun nearly all day, and we're talking about summer time, we can count on roughly 6 hours of sun per average day here in VT, less in some places with even cloudier weather, and as much as 8 hours+ in places like AZ. Here in Vermont, I'd plan on an AVERAGE of 6 hours of sun per summer day. (This means 6 hrs per day average, allowing for rainy days, cloudy days, etc..., but you could get 14 hours of sunlight on a given day -- that just won't happen every day around here.

Typical battery charging (from any source) is only about 80% efficient (20% loss), and I need to replace 1600 watts of power used each day, so 1600 watts divided by 0.8 = 2000 watts. If I want to replace 2000 watts in one sunny day (at the average of 6 h/day in summer), means I would need 2000/6 = 333.33 watts of solar. A good match would be two 175 watt solar panels, BUT -- larger panels tend to be "24 volt" panels which would have to be stepped down to charge a 12-volt battery bank. (HERE is where we have the option to use a 24-volt inverter, and place those 2 batteries in series, which allows us to use the larger "24 volt" panels, which tend to cost much less per watt, than smaller panels. If you need to stick with "12-volt" solar panels, you could use 3 x 110 watts, or something similar. If you don't need to replace all that power in one sunny day, you could get a single solar panel, and allow it to charge for a longer time (or just charge from AC power, if available).

Charge controller: If your interest is summer only (or spring, summer and fall, but NOT winter), use a typical, PWM controller. For 2 or 3 solar panels of 100 - 140 watts, a 15- or 20-Amp controller would be fine (size depends on the short circuit current, or Isc, of the actual solar panels used).

Costs: Inverters can be as little as ~$75 for cheaper models I would not recommend, and for non-sine wave inverters you should expect about $300 or so; more if its an inverter/charger, with an AC charger and transfer switch built-in -- probably $500 - $600 for these. Pure sine inverters will cost more, and if made by a reputable company (buyer beware -- there are junky "truck stop" inverters out there!) will be between $ 500 - $600 for a good inverter, and around $800 - $975 for a high-quality inverter-charger. Basic charge controllers can be $65 - ~$150 depending on the features and digital readouts available. Morningstar Pro-Star 15 is a good option. 12-Volt solar panels are currently selling for about $ 2.50 per watt, while larger panels (nominally 24-volt) tend to sell for about $1.50 - $ 1.75 per watt. Batteries will cost about $125 each, or as low as $35 each if your local battery distributor can find some cosmetic seconds, or blemished batteries ("blems").

Total cost with solar panels, batteries, charge controller and inverter/charger would be around $ 900- $1050 for solar panels, and about $900 or so for the rest (using "Blem" batteries). This would be less if you used the simpler inverter (no built-in charger), and could be more if you bought full-priced batteries. Wiring this stuff up is easy, but you should add ~ $50 - $100 for wire, breakers and a small breaker box, so you can create a nice, neat pre-wired system with the components mounted to a wooden panel.

The premium system would probably be 3 solar panels of about 125 watts each, a ProStar-15 controller with digital display, and a Magnum pure sine 1000 watt, 12-volt inverter/charger with built-in transfer switch. That system can be plugged into grid power to charge batteries with the built-in 50 Amp (DC) charger, and comes with 2 pre-wired GFI receptacles. The whole works (solar, charge controller, inverter/charger and batteries would retail for about $2,125. The federal income tax credit (USA) would be 30% of the total, or $638, so the net cost after tax credit would be a little less than $1500. Using a good-quality inverter/charger and going without solar panels at all, would cost about $1000 less, or roughly $1150 but would not qualify for a federal income tax credit in the US (requires new solar panels).

Sorry that's so long -- hope it helps someone who wants to build a smallportable solar system!

safe spinning and clear skies,

Brad Vietje

Newbury, VT

Re: Solar powered lathe?

#15

Pop Woodworking article treadle lathe? *LINK*

Mike Brazeau

The article is freely available at the link below.


Treadle Lathe Article

Re: Solar powered lathe?

#16

Amazing Brad!

Don Orr

And I mean the article as well as you for doing it. What a thorough and well explained treatise on portable solar power. Even I could understand it and I don't do electricity. (We have an arrangment-I don't mess with it and it doesn't mess with me.)

Well done and thanks!

Re: Solar powered lathe?

#17

Download now if interested.  PW changes available

Craig Daymon

Thanks Mike, that's excellent. I have the issue around somewhere, but this makes it much easier to find.

I'd advise anyone interested (or who might be interested) in this article to save the article. Popular Woodworking does a great job of posting articles from the magazine, but they periodically change what they make available. So don't expect the article to be there if you just bookmark the link.

You can download it by right-clicking on the link provided by Mike and select, 'Save Link As', or some such from the pop-up menu you get from right-clicking. Or, if you go to the link and the article is displayed in your Acroread plug-in, you can save it by clicking on the floppy disk icon in the Acroread plug-in.

The video of the Woodwright's Shop episode, #1806, is an excellent companion to the article. Pop Wood says the video should be available at some time in the future, so you might want to keep checking.

Again, if I were building this, I'd be using routers and tablesaws and set it up with a spindle that would accept chucks and, hopefully MT #2. Tailstock supporting #2 MT as well. If I could get a JET mini with a dead motor, I'd consider building a treadle to power it underneath in a frame similar to the article. That way, no electric, but everything else is first rate. (Vicmark use to make a pretty good quality mini without a motor.)

Re: Solar powered lathe?

#18

Re: YES!  With Details

matt overton

Thanks, Brad. I have been toying with using portable power for a couple of things, as well as a system for my house. this clarified a it a bit.