Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

VFD and Motor

Posts

VFD and Motor

#1

Harry Robinette

VFD and Motor

Harry Robinette

Well I finally did it,ordered a VFD and Motor for my General. I've had a DC drive on it running thru the reeves drive and has been working very well but it's just not enough power and theres to much messing. I have to adjust the reeves drive to a certain speed then adjust the DC drive to get the right amount of torque. I ordered the stuff from Automation Direct 2hp system the VFD has a removable key pad built in thats wireless I really like that, I can use it anywhere around the lathe and it will work for a emergency stop. The cost wasn't as bad as I thought, because I went with the removable key pad remote the VFD and Motor was $417.00 and FREE shipping. It should get here Monday or Tuesday then the installation fun will begin.

I guess it's a good thing I have a couple extra lathes just in case,my mind just might decide not to understand the instructions.

That has been known to happen before.

Wish me luck and I'll try to keep you posted.

Motor=Ironhorse 2hp 3ph 1800 rpm MTR-002-3BD18 $166.00

VFD=Teco 2hp 1/3ph in 3ph out GS2-22PO $251.00

Re: VFD and Motor

#2

Harry, do I remember correctly that....

JamieDonaldson

...your General is a 160? I have one also with the Reeves drive, and may some day decide to convert it to VFD since its the only long bed lathe I have in the shop.

Re: VFD and Motor

#3

Re: VFD and Motor

Josh Bowman

I just programmed a TECO 1 hp drive for my metal lathe. Not saying I'm an expert, but I got it going. The setup was fairly easy. I did have some overload problems at 100 rpm, but that is not really applicable to wood turning much. I got that corrected though by changing one of the programmed functions. Keep us posted to your progress and problems. Good luck.

Re: VFD and Motor

#4

Harry Robinette

Re: Harry, do I remember correctly that....

Harry Robinette

Jamie

you got that right it's a 160-18 originally a 160-12 I put the 18" casting on it.

Re: VFD and Motor

#5

Re: Harry, do I remember correctly that....

Ron Bauer

Harry, I Performed the same upgrades on my metal lathe and mill. Works great. Just be very sure of the electrical terminations between the drive and motor.Otherwise you might be buying a new drive unit. My feed is 120V. If you are feeding 240 the terminations are different. Don't ask how I know that. The frequency convertor reads in Hertz so 60 is max. available depending on your sheave configuration. Once you get it set up you will love it. Ron.

Re: VFD and Motor

#6

Re: VFD and Motor

Lloyd in Mississauga

Harry,

This looks like a great upgrade.

I have a dead DC controller on my 18/47, equivalent to the older DC version of the Grizzzly G0733, that I am looking at converting over to AC. If I go for the manufacteurs version it is about $1100 before taxes and installation.

Was the initial motor speed on your General 1800rpm? Will you need to get a new set of pulleys to get the speed range you had if the motor had a higher RPM?

What are the spec's on the shaft length and diameter?

Thanks in advance

Lloyd

Re: VFD and Motor

#7

Harry Robinette

Re: VFD and Motor

Harry Robinette

Lloyd

My General has a DC drive running through the Reeves drive so I'm just starting to figure out the pulleys.I'm not using the Reeves drive this time.The new motor shaft is 5/8 dia(.658) and 1 3/4 long(1.88) that's what the spec sheet says.

The reeves drive has a very fine vibration built in it, I believe they all do and I'm trying to get that out of the machine.My General is a very nice and with this change hopefully be a very smooth machine.

Now figuring out the pulley set-up should be 2:1 I think but the motor and drive don't get here till Tuesday so I'm going to forget about all of this for a day, maybe that will help.

Re: VFD and Motor

#8

Re: VFD for General 260

bill Crommett

I blew the vfd on my General 260 and didn't want to pay the $1100 for a new one so I got an after market VFD for around $300 which works just fine except it has no torque at low speeds. The sad part is that there is a Schnieder Electric factory, [Square - D] in our town that wouldn't touch the repair job. I took the VFD unit to a local techie who said that the thing that was malfunctioning was a Mitsubishi part that he could only buy in quantities of one Hundred. So, the after market VFD.