After about 20 years of keeping my shop in borrowed space or rented space or heck, even the outside corner of the deck, I have finally managed to get my own shop space. Hard part for me was that this meant a move from Apex to Cary. While they are both small cities outside Raleigh, Apex definitely has a small town feel to it while Cary, with 125,000+ people, definitely feels more "big city". So, I am now part of the "landed gentry"!
I am very excited about the space. It is a garage converted from an existing car port. It measures out about 16x19 and currently has 2 outlets. The electrician comes this week to add more for me. I've already spent time in it just sitting and envisioning the possibilties. Most of my tools are there now, but I still have a few to move over from borrowed space. But it is starting to take shape. I am so happy with it I have to make myself work on the other parts of the house that need setting up! Both boys commented today that there are still LOTS of boxes to unpack!
So, with a tag line now reading from Cary, NC, here's to all the great memories to come and fun times to be created in my OWN shop space!!!!
Mike
Practically giddy with the possibilities in Cary, NC
Excellent! It will be great for you to have a space to call your own. Cary, otherwise known as the Containment Area for Relocated Yankees, used to be a sleepy little town. No more of that as it is now larger than Wilmington in population and is the 7th largest city in North Carolina.
Get rid of those bulky shelves on the right and put in elevated shelving to get back the floor space! Your shop is a little smaller than mine, so you'll need every inch of it. Lathe goes by the door for natural light on a warm day and easy clean-up.
Congrats, and if you have never been to Nana's in Durham, make a trip...
Enjoy the new shop, Mike! Make sure he puts in plenty of outlets. I put 22 in mine and still could use a couple more at times. Feels great having your own space doesn't it? Enjoy!
Thanks for the thoughts and recommendations! Once the electrical part is done, I plan to insulate and cover the walls. Too many places with exposed studs for dust to gather
You are very fortunate that you have a completely "blank canvas" with which to develop your new, "masterpiece" shop!
I have a few suggestions you might want to consider as you develop the plan for your shop and implement the plan in the future:
1. While there is nothing in the room, you might want to seal the floor with an epoxy-based floor sealant as is used on garage floors (a DIY project) before you get going with any other major improvements. This will aid in clean-up, and will be a long-lived, attractive feature for your shop. I really wish I had done this first.
2. While your electrician is there, you should be sure to provide for both improved ambient and task lighting (which should be on a different circuit than any machinery), if possible add a 220V circuit for any future expansion/use of higher power lathes/tools, and add a separate circuit for a dedicated dust collector unit. Some of these circuits might become more convenient to use with separate switching at specific locations in the shop.
3. Consider having a dedicated space for off-lathe finishing, carving, woodburning, surface embellishment, or other activities - I had to do major re-arranging of my shop to accommodate these techniques. Several of these require adequate ventilation, so plan accordingly.
4. Walls should be finished with a light colored paint or paneling to maximize ambient light in the shop. Tool racks, wall cabinets, shelves, etc. all contribute to reduced light reflectivity, so make use of light colored surfaces whenever you can.
5. Storage for wood supplies/blanks, drying of roughed blanks, etc. is a HUGE consideration, so make use of every last available space in your design. You will NEVER have enough space, so think out this aspect of space use carefully.
You might want to have a quick read of some short articles I wrote for the AAW's Woodturning Fundamentals newsletter about setting-up an efficient shop and woodturning workstation:
Good luck setting up your new shop, and don't be afraid to visit shops of friends to get ideas of how they solved problems to arrange their shops in the most space-efficient manner.
I started out with a clean canvas and put in some innovative things for my shop. Every week I run across something that I categorize as a "shouda done - coulda done".
As Rob says, you will never have enough space, so move on and have fun. my floor is particle board so I gave it two coats of squeegeed on cheap varnish to seal it. It has stood up quite well for twenty years.
Consider putting some outlets in the ceiling. Outlets above your work area are great and prevent cords being strung all over the floor. It also makes it easier to clean up the floor.
I have 6 in the ceiling and 12 on the walls and wish I had more.
Mike is right on the ceiling outlets. I have my shop in my basement and most of the outlets are in the ceiling and I find them very convenient. It is nice to have a garage door also. On a nice day you can open it up. You can also use a leaf blower to blow all the shavings out the door. Your new neighbors in Cary will love that. Congratulations on the new space. You will really love the convienence.
Since my workshop is in my basement, it was/is easiest to run all the wiring along the 'ceiling' (exposed floor joists). Initially I attached the boxes to the bottoms of the joists, which were just barely within reach. I finally realized that they should be mounted just above head level. That has made life much easier (and works better with the relatively short cords on most machines). Just had an electrician in last week for a 220 circuit since I finally needed one; there are five 120 circuits.
Hi Mike -- Congratulations on the new shop. My suggestions, based on my own empty-room move-in in 2009:
Cover your concrete floor with a layer of cheap OSB-type plywood, then prime and paint several coats with a latex floor enamel. Your tools will appreciate a softer landing. One of my friends talked me into this when I had an empty floor to start with and I have never regretted the time and expense involved.
OSB is pretty cheap. I "glued" it down with Liquid Nails, very generously applied. The new non-VOC version doesn't have much "stick" and there are clearly some spots that are not really attached. But I've been here 3-1/2 years now and I can't say that this is a problem at all -- gravity does most of the work keeping it down, plus of course all the stuff that sits on top of it. Be sure to follow OSB recommendations for spacing between sheets (I learned this the hard way); if they don't close up completely in a couple weeks, you can fill the remaining cracks with caulk and in a few months you won't even notice.
Consider putting your lathe(s) in the middle of the room (my space is 16x24). I was a little skeptical when I started out with them this way but now think it may be the smartest thing I did, much more flexible than having them against walls. Electricity from drops overhead, both 220 and 120.
Get a nice wide window for that back wall. Nothing beats real daylight.
Wall cabinets -- check craigslist "materials" for used kitchen cabinets being disposed of cheap from a remodel job. Also for the window mentioned just above.
Air conditioning -- Mount a window-type a/c unit in your exterior wall. If you're nervous about putting it through drywall, just use a piece of plywood instead on one section of wall and you'll have a nice stout box-beam to mount it in.