Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

OT ? : Chuck lubing tip

Posts

OT ? : Chuck lubing tip

#1

OT ? : Chuck lubing tip

Jim Breeden

When I received my last Nova2 Chuck and, set about disassembling and cleaning all the sticky shipping crud (grease ? :b ) out of it, using lacquer thinner. But, what to do about a spot of lube to make it operate better. I know not to use any dust attracting material to gum up the works - hey! - I have some Permatex Anti-Seize, part #133A! All it takes is a q-tip to apply a spot to all the moving parts, i.e., scroll, gears, and jaw sliders. Not to much, as "a l'il dab'l do ya". Also, put a dab on the jaw screw threads to prevent the screws from "locking" in the sliders. I usually disassemble my chucks every six months or so for cleaning, and have as yet to find any dust, dirt, etc, attracted to the anti-seize.

Re: OT ? : Chuck lubing tip

#2

Re: OT ? : Chuck lubing tip

Bernie Weishapl

Jim that is good to know. I have some of that anti seize but was afraid to use it or any grease for fear it would clog up with dust. I just cleaned mine yesterday. I ran them thru my clock ultrasonic and it does a great job on them but I lubed them with graphite. I also have some spray lube that dries into a dry lube. It does work pretty well but can't find it anymore and the can is about empty. I guess next time I will give the anti seize a try.

Re: OT ? : Chuck lubing tip

#3

Re: OT ? : Chuck lubing tip

Dale Miner

For several years now, I have been using a can of dry film lubricant that contains moly disulfide. Comes in a sray can; easy to apply, dries fast, makes the moving parts look charcoal dust colored. It does not gather dust from sanding or turning.

Re: OT ? : Chuck lubing tip

#4

Re: OT ? : Chuck lubing tip

John Veerkamp

Dry lube is used widely in electrical motors and in farm equipment. I get mine at a farm supply store. It is also sold as lube for garage door openers. Found with the door openers not the lubricants in box stores.

Re: OT ? : Chuck lubing tip

#5

Re: OT ? : Chuck lubing tip

Devon Palmer

I've had good luck with Teflon dry lube. http://www.amazon.com/DuPont-Non-Stick-Dry-Film-Lubricant-Aerosol/dp/B003UTX0R8/ref=pd_sim_hi_5

Re: OT ? : Chuck lubing tip

#6

Harry Robinette

Re: OT ? : Chuck lubing tip

Harry Robinette

I've been using PG2000 for my chucks,also the ways on my lathes and anything else that get's in my way.

Re: OT ? : Chuck lubing tip

#7

Ellis Walentine

Another possibility

Ellis Walentine

I used to use White Lightning (bike chain lubricant, not moonshine) on tablesaw worm gears and other dust-sensitive parts (gibs, screw threads, etc.). Never tried it on a chuck, but I'll bet it would work great. I think it is a solvent-borne wax emulsion that is dust repellent when dry.

Ellis

Re: OT ? : Chuck lubing tip

#8

Re: Another possibility

Mark ravensdale

I use a lube on my workshop door locks (padlocks ???) you spay it on as a liquid, but then after abt 1 hour it turns to a wax like lube, bet that would work ok!

Personally I dismantle and clean my chucks every 12-18 months and so just use normal grease on them (but not too much of course!) never had a problem with them fouling up or getting sticky in 9 years of constant use ( every day 2-5 hours)

I too have tried that anti stick lube before (copper grease???), and as long as you don't get heavy handed with it it works ok, I use it on the screws that hold the chuck jaws on, whenever I buy a set of oneway chuck jaws the screws that come with them always seem to have it on them so it must be ok I think (I hope!!!)

Re: OT ? : Chuck lubing tip

#9

Re: Another possibility

Jim Breeden

Thanks for all the lube tips everyone. I was trying to figure out what to use that I had on hand, and the anti-seize was it. I used to rebuild engines in another lifetime, and that's what we used to keep the rocker arms from galling and the cam lobes from scorching on initial startup, so I figured what the heck, this see what happens. Of course we used more that a lil' dab, more like a glob.