Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

testing sliding miter sled

Posts

testing sliding miter sled

#1

testing sliding miter sled

John Lucas

I had to redo my miter sled to make it fit my new table saw. I made this sled adjustable but it was always a pain to reset. I added some brass pins. One is fixed and the other is on the adjustable arm. Once the miter arm is set I measure from the outside of the pins and should be able to set it within a thousandth or two to dead on every time.

I tested it of course. It took about 5 rings to really nail it. I got carried away and just kept on cutting.


Re: testing sliding miter sled

#2

Ellis Walentine

A thousandths of what?

Ellis Walentine

Nifty jig, John. Are you aiming for a particular angle with these cuts? and, if so, are you setting your dial caliper based on the trigonometry of the fence?

Ellis

Re: testing sliding miter sled

#3

Re: A thousandths of what?

John Lucas

This rig is for duplicating any of the segments that I want. I'm not a trig or math person at all so I'll set the angle as close as I can measure, then I'll run test cuts until I get it dead on. then I'll measure it so I can repeat that angle.

It's now set for 16 segments. I need to do some 12 segment rings so I'll probably do that next week. My goal is to have5, 6, 8,12, 16, 24, and 32. That should cover most anything I do. I don't have room to store dedicated sleds.

Re: testing sliding miter sled

#4

Re: A thousandths of what?

John Lucas

I didn't answer all your question. I measure the gap between the brass in inches to the thousandth. Then I make a note on the sled the angle, number of segments, and distance in thousandths so I can reset it any time.

I've tried lots of other methods and most are close but I end up testing anyway to get it dead on. I'm hoping this will eliminate the testing.

Re: testing sliding miter sled

#5

Mike Stafford

Re: A thousandths of what?

Mike Stafford

John, that is pretty imprecise work you are doing there. Measuring to the thousandth's.....001. Sheesh! When you get good you'll be measuring to the ten-thousandth's......0001.

:b :b :b :b :b :b :b :b :D

Re: testing sliding miter sled

#6

Re: A thousandths of what?

John Lucas

What do you expect from a guy who makes goblets that are .023" tall. Mike I do take a lot of flak from other woodworkers when I measure my wood with dial calipers. One friend said it moves more than a thousandth overnight. I said True, but if I make the 2 parts fit to within a few thousandths they will still fit tomorrow.

Actually that far out from the fulcrum point I would probably not need to measure to the thousandth but that's a convenient measurement with a dial gauge. I have found that just a single turn of my micro adjusting knob will change the cut from a perfect fit to not so perfect when your doing 16 segments. It's a 1/4x20 screw so that's 1/20th inch 18" from the fulcrum point. It's even more critical for 32 segments.

Re: testing sliding miter sled

#7

Re: testing sliding miter sled

Hal Taylor

John, that's a very interesting design for cutting segments. I've not done any segmented work so I'm interested in how it works. One of you wonderful how to videos would be great.

Re: testing sliding miter sled

#8

Mike Stafford

Re: A thousandths of what?

Mike Stafford

I also measure my segments with calipers... Once you get the set up right it is repeatable and trial and error wastes a lot of wood.

Re: testing sliding miter sled

#9

A thousandth of a Planck lenght!


Re: testing sliding miter sled

#10

According to Physicist

Jorge

a Planck length is the theoretical smallest measurable dimension.

An John cuts to a thousand of that!

Re: testing sliding miter sled

#11

Leo Cuellar

Re: According to Physicist

Leo Cuellar

Too funny, Jorge! All wood working always comes down to "plan(c)k" length. :D

Re: testing sliding miter sled

#12

     

Jorge

Right you are!

Re: testing sliding miter sled

#13

I think I'll just walk the plank 


Re: testing sliding miter sled

#14

Wear

Mark Mandell - Gone Round In New Jersey

your very smallest shoes, John