Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

Wolverine new idea

Posts

Wolverine new idea

#1

Wolverine new idea

Josh Bowman

Not sure if this is a good or bad idea. But I got tried of dealing with the board template that Oneway suggests for setting the tool holder.

So I just set them with the template and drilled and marked a hole in the holder and put a finish nail in to index the holder .

Now I don't have to find the templates anymore. What do you think?

Re: Wolverine new idea

#2

Should work.

Greg Haugen

I see you have diamond wheels so it should work. If you had grinder wheels, it would slowly change with the diameter of the wheel. For your setup, it should work.

Re: Wolverine new idea

#3

Re: Wolverine new idea

galen vetterick

That only works for one tool length and in time even that tool will get shorter the way I see it.

Re: Wolverine new idea

#4

Lyle Jamieson

Re: Wolverine new idea

Lyle Jamieson

If i understand you, the 2 inch set back of the jig sets up the length. It will not matter how long the gouge or handle is.

Re: Wolverine new idea

#5

Lyle Jamieson

Re: Wolverine new idea

Lyle Jamieson

The pivot point or sliding arm position changes the side angle of the swept back grinds. It might get wacky on the side but might be a small enough change to work ok.

Re: Wolverine new idea

#6

Re: Wolverine new idea

Craig Daymon

I think Galen is correct. As the wheel wears and gets smaller with the proposed set up, the wheel will naturally be farther from the pivot point of the jig, all other setting being the same. This will result into a steeper and steeper bevel being ground on the end of the tool. The blocks insure that the arm is moved forward when the wheel has worn, maintaining the same distance from the arm pocket to the wheel.

Easy way to prove this would be to put, if you have one, a 6" wheel on the grinder and see what the result is.

Re: Wolverine new idea

#7

Re: Wolverine new idea

Josh Bowman

Opps, you guys caught me! I left out that this will only work with a CBN type wheel and it's for the varigrind setup. Sorry 'bout that.

Re: Wolverine new idea

#8

Re: Wolverine new idea

John Lucas

Josh Won't work if your wheel changes size. It will work really well for the CBN or Diamond wheels that don't change size but as the wheel gets smaller it changes your bevel angle. That's why I use the homemade gauge that I use that fits in the V arm and touches the wheel at 2 points. It compensates for wheel wear.


Re: Wolverine new idea

#9

Re: Wolverine new idea

Galen Vetterick

Varigrind setup clears up how you can keep same setting for your wheel that does not change size. Tool always indexed from the jig end so wear not a problems. My mind was not working as usual.

Re: Wolverine new idea

#10

Steven Antonucci

That's the Tormek solution (or the Raptor)


Re: Wolverine new idea

#11

Re: Wolverine new idea

Josh Bowman

John,

I like your wooden jig, but like the Oneway template type, I found with my rig, the slop/droop in the Wolverines locking system moved the arm up when I lock it, enough to change the grind angle on occasion. I'm not trying to get an exact angle, just consistent one, so I don't grind too much. So with the pin idea, you shove the arm in until it hits the pin and lock it, my arm seems to stay indexed more consistent. The biggest plus for me is I don't have to look at anything to insure the wheel and pocket are in contact with a jigs index points. This is based loosely on Reed Grays tool rest.

Re: Wolverine new idea

#12

Lyle Jamieson

You are right on Josh


Re: Wolverine new idea

#13

Re: Wolverine new idea

phillip medghalchi

John, I am like you I have the white wheels that came with my woodcraft slow speed 8" grinder. However, I'd like to ask that how or where did you find the template to set up for that setting for sharpening? Can you share, please?

Re: Wolverine new idea

#14

Re: Wolverine new idea

John Lucas

I simply modified the template. I first saw it in one of Mike Darlow's books. It was a 3 point template that had 2 brass pins that touched the wheel. This is probably more accurate by a tiny bit but it was much more complicated to make. I simply set my jig to the normal setting. Took a thin piece of plywood that I cut into a sort of V or diamond shape. I put the bottom of the V in the Oneway V arm and layed the plywood against the wheel. I traced the curve. Then I cut it out on the bandsaw. Then to make just 2 points to touch the wheel I cut out the middle section. When it was all cut I place it in the jig and turned the grinder on. Then I touched to jig to the wheel to kind of burn in the two touching points so it was really accurate.