Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

Truing up tool rest

Posts

Truing up tool rest

#1

Truing up tool rest

Robert

I have occasionally filed the top of the tool rest to remove dings. I decided to also check for level and found a 1-2 mm difference between the ends that are 14 inches apart. I am looking for an easy way to get the top of the tool rest level. I can measure/file/measure but would like to be a bit more precise. I hope to avoid the scenario of trying to level a table by cutting/filing the long leg and ending up with a table with 12 inch long legs. Belt sander? Thanks in advance.

Re: Truing up tool rest

#2

Re: Truing up tool rest

Philip Duffy

I use a 12in bastard file, laid along the long axis to get it flat, then move to sanding grits on the file to get it smooth, followed with some hard wax.

Re: Truing up tool rest

#3

Re: Truing up tool rest

Greg Haugen

Personally, as long as you're filing your rest to keep it smooth-free of dings and nicks, that's more important than if the ends of a 14" rest are 1 to 2 mm different in height. No matter what you do to level it, short of scribing a level line and filing to it, chances are you'll teeter the other way, etc. If we were machinists it would be a different story. The turning or you will not notice a mm or two change over 14 inches. It may be your banjo's casting, or your floor. It's not worth worrying about it.

By buying one of Robust's rests you'd remove the need to file it at all.

Re: Truing up tool rest

#4

Re: Truing up tool rest

Joe Herrmann

I'm with Greg--I wouldn't even bother to try to level the tool rest.

Re: Truing up tool rest

#5

Re: Truing up tool rest

John Lucas

I agree with the other two. If your tool rest were perfectly level that act of moving the handle just a hair up or down would change the cut by 1 or 2mm quite easily over than length and you would still be off. If you need a perfect cylinder it's better to measure as you cut and remove what needs to be removed. If you using a scraper just pushing the tool forward or back will also cause that much inaccuracy. I've been experimenting with getting a perfectly flat face on large platters using the tool rest as my standard and sliding my hands along it with a scraper. Even this is difficult.

If your dead set on adjusting the level then a technique called Draw Filing is the way to go. Lay the file on the rest so it's perpendicular to the rest. Then push it with one hand on the handle and one hand on the other end. This cuts aggressively with a courser file would not take too many strokes to flatten it. You will need a precise way to measure to know that you've achieve the flatness. Center drill a 15" round piece and mount it between centers. Slide the tool rest under this and use a feeler gauge to measure. Drilling the center of the piece would be the challenging part.

Re: Truing up tool rest

#6

Lyle Jamieson

Re: Truing up tool rest

Lyle Jamieson

Did you check the other variables?? Is the lathe bed level?? Is the banjo the problem?? Leaving the banjo in place turn the tool rest 180 degrees and check for level. Try it parallel to the bed, try it perpendicular to the bed. Filing it one way might make it off the opposite way.

Re: Truing up tool rest

#7

do you mean level or flat?

Dick Coers

What machine do you have, and what material is the rest made from?

Re: Truing up tool rest

#8

Re: Truing up tool rest

Robert

Thanks for all the responses. My intent is to level the tool rest relative to the lathe bed. The 1-2 mm difference is measured from the bed to the top edge of the rest. This is a PM 3520. I do have 2 Robust rests of the shorter variety. If I keep filing away at the PM rest I'll have to get a longer Robust tool rest and the problem is solved. I am going to go with those that said not to worry about the difference. For now I will continue to file to keep the rest flat and ding free. Dings and nicks in the tool rest are much less frequent than they were several years ago.

Re: Truing up tool rest

#9

Re: Truing up tool rest

Jerry Klug

When it is worn/filed down enough, you can have a piece of drill rod braized or epoxied to the top edge for a smooth rest contact area that is parallel to the bed.

Re: Truing up tool rest

#10

Re: Truing up tool rest

steve worcester

normally it wouldn't make much difference, 2 mm. If you are using it for a captive hollowing system, you can end up aligning on center and end up 2mm below at a different part of the rest.