Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Johannes jig

Posts

Johannes jig

#1

Johannes jig

John Lucas

I built a copy of the Johannes sharpening jig this morning so I could try out his grind. It just barely changes the grind that I already had on my Thompson 1/2" V. I was using the Wolverine jigs in the ONeway V arm. It seems to slant the wings in a little more which would make sense since your moving the base of the Wolverine off center to grind each side. I hope to learn the differences between his grind the the one I've been using for years which is more or less just like the Grind that comes from Doug except I grind away much of the bevel below the initial grind.

I was going to post a video of him using his new tool but I must have lost it. I'll keep looking.


Re: Johannes jig

#2

Re: Johannes jig

Dick Coers

I one comment I will make on your knockoff is that the holes may need a little more shaping. On the Hannes fixture, they are elongated so the sides of the holder bar don't contact the surface where the plate and hole contact. Are you using the varigrind holder, or more like a Elsworth holder? The Hannes and Elsworth are round bars and would play better with the locating hole. So there are some subtle differences on the purchased fixture.

Re: Johannes jig

#3

Re: Johannes jig

robo hippy

In an earlier thread, Johannes did say he was going to get a video of that up. I have to see it just to figure out if I can grind it on the platform. From his explanation, it sounds like you remove most of the bevel, and the outside/wing bevel is so small, that by the time you roll it far enough over to cut with, you are past the point where it will dig in, and to the point where it makes a scraping cut. Need to check it out in person. This is speculation on my part.

robo hippy

Re: Johannes jig

#4

Re: Johannes jig

bob elliott

Johannes also uses a 2 3/8" exposed length on his Vector instead of the 1 3/4"-2" commonly used on the Oneway Varigrind.

Re: Johannes jig

#5

Re: Johannes jig

JoHannes Michelsen

John,, It is not considered OK for you to

rip off anything weather it be a product or artwork!

I worked long and hard to derive what actually can produce

The grind that I did freehand for 35years your quickly rip off

Doesn't work because you clearly don't under stand all the

Dinamics involved.

You are absolutely wrong in your claims about how it produces

A high functioning grind, the real thing truly works to perfection

So say 300 plus happy customers!!

If you only made the pivot plate then you are sorely missing

The point! The vari-grind just doesn't do it.

This thing is much broader and deeper thAn you are Apparently

Capable of perceiving.

If you really want to try my grind it seems you will need some

Instruction and the real deal Vector Grind Fixture and

A health dose of scruples.

Hannes

Re: Johannes jig

#6

Steven Antonucci

I still don't understand why you need a jig...

steven antonucci

to grind the heel off of the gouge? Maybe I'm missing something?

I have gotten this grind out of my Tormek for years using their standard jigs. I knock the heel off on a cheap bench grinder because it is faster and it doesn't really matter (it doesn't cut, and I just need to remove steel quickly). I lay the tool with the heel against the wheel and just rotate it. You can't do it wrong, and there are no points for "pretty heels"...

S

Re: Johannes jig

#7

Re: I still don't understand why you need a jig...

John Lucas

the point of this jig is not about grinding the heel. That's a secondary consideration. The point of this jig is to somewhat duplicate Johannes radiused gouge. It doesn't put a true radius on the but does round over or angle the wings in more than the Wolverine jig place in just the center hole.

Imagine placing a diamond hone on the primary bevel of the tool. The lift it off the bevel on the bottom so it's only cutting the edge. Now make a few passes. This is kind of like a micro bevel on a carving tool that has a slightly blunter angle. That's what you get with this jig. I thought it would be fun to see if I could tell any difference between that and my other gouge that has the traditional grind. I do grind my bottom bevels off on that tool also.

Re: Johannes jig

#8

Steven Antonucci

Six of one, half dozen of the other?

steven antonucci

The edge is created with the two "offset" holes on the wings. The middle holes grind away the heel.

If I use a conventional grinding fixture to grind the whole bevel, and then cut away the heel, all that is left is the micro bevel? Granted, it gives me more control to do it with the jig, but in the end, I am left with a small bevel and no heel?

I've watched the video a couple of times, and that's all it looks like to me? I still don't see it...

S

Re: Johannes jig

#9

Re: Six of one, half dozen of the other?

Dick Coers

The gouge is extended further from the pivot, and the pivots are further out than anything else out there. The grind has different angles around the flute. It does work differently than any other jig.

Re: Johannes jig

#10

Steven Antonucci

three variables.of grinding jigs

Steven Antonucci

1. How much the tool projects from the fixture. There is nothing that any jig does to control this. The user sets it to whatever the want. Hannes jig has a part that sets the distance. I have a line on my grinder bench.

2. The distance of the pivot pint to the wheel. The is also something that can be set easily. I lied about the line on my bench, because I bought the Tormek TTS jig. It has three set disrances for #1, and 2 distances for setting #2. It is basically a board with a hole in it, but I paid $30 for it because my board was getting wet and warping.

3. The rotation about the axis/pivot point sets the angle and the wing shapes. Rotating about this point is why we make jigs, since it's hard to control the shape otherwise. I don't see that moving the point at the bottom of a Varigrind out one inch off center on either side does anything but change the geometry of the first two measurements?

If I move my Tormek jig out of centerline, I get the same grind as if I line it up on the center of my stone. It just makes my stone wear more evenly. Perhaps it is that this jig replicates what Tormek has had available for 10 years?

Steve

Re: Johannes jig

#11

Re: three variables.of grinding jigs

JoHannes Michelsen

First we need to understand that there is. Jig for grinding Woodturning

Tools!

A jig by definition is a device that one clamps a work piece in and moves

thru a defined motion and the jig replicates a pre-determined shape. The

devices we clamp our tools in for grinding require our participation!

First thing we need to know is what shape grind we want be ause we must

By the nature of the beast be part of the process creating the shape as we grind

So the right name for these devices is "Fixture", they help us but they don't

determine anything.

For my grind one must use way more projection to get the tool to roll over more

so the angle on the front of the gouge wraps around to both side consistently.

That is the key to a hi-functioning grind. All of the geometry of the set up must be

correct that's why just making a pivot plate and useinga vari-grind doesn't work!

My depth guide is not really about the depth that can be done with a line on the

bench or a hole in a board like Steve said. It is all about indexing the flute up out front

unlike other fixtures which do it in the tool hold device which makes it impossible to

grind all the flute length--not good!!!