Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

Parting tool on large blanks?

Posts

Parting tool on large blanks?

#1

Allan W

Parting tool on large blanks?

Allan W

Today I roughed out a blank that was to large for my band saw to cut and didn't want to waste all of the wood on the end, so I used my parting tool to part off some of the blank. It took awhile to get through to the center, but I got a nice smooth bottom for my bowl and a nice flat top for the next bowl. When it had about an inch left, I stopped the lathe and then used my large screw driver to break the two pieces apart. My only problem was when I got close to the center, the parting tool was jumping quite a bit. I think I need to find one that has a longer blade and handle?

Re: Parting tool on large blanks?

#2

Probably just a longer handle.

John Lucas

Also it's easy to get off the bevel of the tool and start scraping the cut when you get close to the middle. When I"m parting things like this I make 2 cuts so the kerf is just a little wider than the tool. It makes for less work. When I get close I stop and use a little pull saw I got from Woodcraft a bunch of years back. Oh the lathe is stopped when I use the saw. Also remove the tool rest so you don't ruin the saw teeth by making a nice mark in your tool rest. :)

Re: Parting tool on large blanks?

#3

Mike Stafford

Re: Parting tool on large blanks?

Mike Stafford

Sometimes I start the cut with my parting tool going as deeply as I dare and finish it with a handsaw while the blank is on the lathe.

Re: Parting tool on large blanks?

#4

Re: Parting tool on large blanks?

phillip medghalchi

I applied just about the same technique, however, i was working on black walnut and it started burning and boy it stunk, so I had to stop and cut with a Japanese hand saw rest of the way, but I still got a bad burn mark on the top of the box bottom which was going to be hollowed away and bottom of the top of the box which I really wanted to save as much as could to match the lid and the bottom grain. Any advise on this?

Re: Parting tool on large blanks?

#5

Re: Parting tool on large blanks?

John Lucas

Make 2 cuts. This enlarges the kerf so it doesn't rub against the parting tool. To save wood make your first cut straight in. Then use the outer edge as a sort of pivot point. Move the handle left and make a cut while pivoting the tool at the outer edge of the spindle. Then move the handle to the right and make a cut. Keep doing this going deeper and deeper with the tool see sawing around that pivot point. This keeps the cut at the outer edge of the spindle as narrow as you can and enlarges the hole inside so it doesn't rub on the parting tool. Does that make sense? It's hard to explain.

Re: Parting tool on large blanks?

#6

Then you need the quick core tool... *LINK*

Dick Coers

designed by Johannes Michelsen, sold by Robust.


quick core tool pdf

Re: Parting tool on large blanks?

#7

Re: Parting tool on large blanks?

robo hippy

If you are going to part off sections of bowl blanks, the McNaughton coring system straight blade is the best, safest, and most efficient way of doing that. Standard parting tools are not heavy duty enough to reach out safely more than maybe 2 inches.

robo hippy

Re: Parting tool on large blanks?

#8

Mike Stafford

Re: Parting tool on large blanks?

Mike Stafford

Phillip, I hope you were not using the saw to saw the blank with the lathe running. That is very dangerous. If the saw blade were to bind it will become a limb removing whirling dervish.

Only use a saw with the wood stationary.

Re: Parting tool on large blanks?

#9

Allan W

Re: Parting tool on large blanks?

Allan W

Thanks for all the help. :) This is the first time I had cut up a log for turning and made some of the blanks to thick. The next one I hope to be able to cut so that I can use my band saw.

Re: Parting tool on large blanks?

#10

Re: Parting tool on large blanks?

phillip medghalchi

:\ Mike, of course, not. I stopped the lathe and did rest of the way by hand W/O lathe running. I have learned that long time ago with the parting tool pulling in between my little finger and the tool rest and ripped my little pinkie side way. Fortunately, I was lucky that I was at a friend's shop who is physician assistant and he also used to work in the emergency room at the VA hospital here. He immediately took me to his office and actually used the Medical CA glue and glued the ripped part together. That was my lesson early on in my turning to be mindful of the tools when behind the lathe. I have paid my dues to get to this point in my turning hobby, and I am praying that i don't have to pay any more dues and can live to turn many many years. Thanks to all the wonderful friends here on this site and others that help by sharing their experiences with me and the other turners.

Re: Parting tool on large blanks?

#11

Mike Stafford

Re: Parting tool on large blanks?

Mike Stafford

Phillip, I get afraid everytime I hear of someone using a saw on the lathe with it running. I had a student do it and the saw caught in the wood. Fortunately he was able to get out of the way.

Just wanted you and everyone else to be safe.

Re: Parting tool on large blanks?

#12

Re: Parting tool on large blanks?

phillip medghalchi

Mike, I appreciate your concern. Let me correct something here so the readers will know why you do the sawing on the lathe. You notice that you start the cut by parting the piece (well you must have the wood in the chuck or on a face plate, or fixed tightly somehow) so your piece is secured and then you can only go so far before you get burning as a result of sides of the parting tool rubbing in the Cerf or you are running out of the length of the parting tool. Therefore, you STOP the lathe and then proceed as John said with a saw (Japanese preferably) on a backstroke cut and proceed to finish the cut. Echewwwwwwwwwwww, man this came out even longer than the Sunday sermon. Meanwhile, you are building your biceps stronger and now you are ready to go have your iced tea. :D .

Re: Parting tool on large blanks?

#13

Re: Parting tool on large blanks?

JoHannes Michelsen

Dick, Robust was the maker of the QuickCore tool for me but

Has decided to back out. I still have some of those but have

decided to redesign it. Brent's design was too long for shipping

And or travel, the new design is telescopeing and more versatile.

I'll post a pic when I have one done.

Hannes