Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

New steady rest idea - Any good? And a 2nd idea.

Posts

New steady rest idea - Any good? And a 2nd idea.

#1

New steady rest idea - Any good?  And a 2nd idea.

Craig Daymon

I was thinking about UHMW, since I just bought some to make center end caps from. (Cup centers, cones, etc.)

I started thinking of using it at the ends of the arms of a steady rest instead of skate wheels. Thought it might add an extra inch or more of diameter to the maximum piece usable with the rest. The UHMW is non-marring, slick, but not oily and long wearing. It doesn't absorb vibration as much as the urethane of the wheels, but then a steady rest is suppose to insure that the piece does not vibrate.

Also, for a non-jig, project idea, I was looking at David Springett's, "Woodturning Full-Circle", book and looking at the chapter on "Turning Square Holes" and, in particular, page 171, image 9. It would be possible to glue the 2 V-shaped sections together to create a square shaped, half circle. If before gluing them together, you epoxied in a very small strip of UHMW into the bottom half, you could then turn another square shaped piece to fit the curve and create a box with a drawer in a very interesting shape. It would require a very minor bit of flat work to make a door for the drawer.

The UHMW isn't essential, but it would help in smooth operation of the drawer. Might even help to use 3 strips, one on the bottom, one on the inside corner of the outer wall and one on the inside corner of the inner wall.

Might be a big project for my mini, but still doable.

Thoughts? Comments?

Re: New steady rest idea - Any good? And a 2nd idea.

#2

Re: New steady rest idea - Any good?  And a 2nd id

David Walser

Your steady rest idea should work fine. One of the first spindle steady rests I saw, made by Delta IIRC, did not have wheels. It just had cast iron or steel arms that has been machined smooth on one end to serve as bearing surfaces. Step one was to turn a smooth, flat spot for the steady rest. Step two was to apply paraffin. And step three was to install the steady rest and adjust the arms so they barely touched the spindle as it turned. Seemed to work well. Using UHMW should be an improvement on this old design.

Let us know how it works.

Re: New steady rest idea - Any good? And a 2nd idea.

#3

Re: New steady rest idea - Any good?  And a 2nd id

Roger Chandler

Your idea may work.......but for my use, I would prefer a wheel with a bearing center that rotates.........I have used UHMW just recently and made a rotating vacuum adapter........that stuff machines nicely, but I would much rather have a contact by a rotating wheel........just me personally.

Re: New steady rest idea - Any good? And a 2nd idea.

#4

Re: New steady rest idea - Any good?  And a 2nd id

Dale Miner

Give it a try, but I think the friction between the UHMW and the wood will eventually burn the wood and or melt the UHMW. Delrin is a harder material and would be my choice for giving it a try.

Re: New steady rest idea - Any good? And a 2nd idea.

#5

Re: New steady rest idea - Any good?  And a 2nd id

John Lucas

I agree with Dale. The stuff turns easily so just make a hole for a bearing and you can have wheels.

Re: New steady rest idea - Any good? And a 2nd idea.

#6

Re: New steady rest idea - Any good?  And a 2nd id

Joe Meirhaeghe

If your using it to turn wet wood it will bruise the wood where it rubs. When you rough turn your piece let dry then re turn it the bruise will probably be to deep to turn out of it.

On dry wood I'd think that you'll still have enough friction to either burnish or crush he woods fibers that it will stand out where they rub after finishing.

Re: New steady rest idea - Any good? And a 2nd idea.

#7

Re: New steady rest idea - Any good?  And a 2nd id

Dick Coers

Steve Sinner is an advocate for hard material wheels to reduce vibration in large vessels. But, it still is wheels for the contact. Look at his steady, lots of contact area with the wood.

Idea two; "If before gluing them together, you epoxied in a very small strip of UHMW into the bottom half"

Nothing sticks to UHMW (well nothing I know of), you need a mechanical fastener.

Re: New steady rest idea - Any good? And a 2nd idea.

#8

Re: New steady rest idea - Any good?  And a 2nd id

Craig Daymon

A mechanical fastener is achieved by cutting shallow grooves in the UHMW plastic that would fill with epoxy when gluing. The epoxy hardens and forms the mechanical fastener. Probably only need to be a little more than deep scratches. Or some variation of that idea where the epoxy forms the fastener, maybe around a metal or wooden pin or screw.

Re: New steady rest idea - Any good? And a 2nd idea.

#9

Re: New steady rest idea - Any good?  And a 2nd id

Dick Coers

How about dovetail grooves in the UHMW?

Re: New steady rest idea - Any good? And a 2nd idea.

#10

Leo Cuellar

Any good? Yes, John's...

Leo Cuellar

recommendation works very well, this is a little steady I made to run in an extra banjo that I have.

Re: New steady rest idea - Any good? And a 2nd idea.

#11

Re: New steady rest idea - Any good?  And a 2nd id

2B6

Craig are you trying to reinvent the wheel? :D What is there to gain from using it over the wheels?

I can't think of anywhere UHMW is used in a place where fiction would cause heat. Its melting point is between 266 & 277 F degrees.

Dick you can get thin UHMW w/ adhesive on the back to put on your rip fence or router fence. Apparently something sticks to it. ;)

Re: New steady rest idea - Any good? And a 2nd idea.

#12

Re: New steady rest idea - Any good?  And a 2nd id

Craig Daymon

The idea was that skate wheels, as good as they are for the job, have 2 issues that I thought UHMW might conquer. First is their size. Using UHMW, you could make relatively small contacts (as in minimizing distance from mounting point) that it would allow more room inside the steady rest ring. Second would be that UHMW has less give than urethane wheels, thereby providing less flex/more steadying than the wheel under the vibration of turning.

You could make UHMW contacts smaller than the bearings in the wheels that would suffice, though creating UHMW wheels, maybe about 1" in size might be the best solution. Then they could spin and be more rigid. No need for a bearing as the UHMW running on the axis is bearing enough.

Re: New steady rest idea - Any good? And a 2nd idea.

#13

UHMW rubbing vs wheels

Jim Bodin

UHMW either wears or melts - I've tried it. Wheels of some sort are the answer.