Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

Tool rest tightening handle?

Posts

Tool rest tightening handle?

#1

JL

Tool rest tightening handle?

JL

First - what the heck do y'all call it?

Next - do y'all have a particular side where you like to have it?

I decided to swap sides on mine as it was rubbing against the tailstock when I was using my chuck. I had plenty of room on the chuck side (headstock side) when I use my larger tool rest, but none on my tailstock side. Seeing how the hole was already tapped, I figured that's what it was there for.

It's taken awhile to get used to it, but I'm managing. The big Jet banjos also have a tapped hole on the outside of the tool rest post. So it got me wondering - if anyone had a preference for where the handle went.

Re: Tool rest tightening handle?

#2

Re: Tool rest tightening handle?

John Lucas

My 3520A has 2 holes for the tool rest locking handle. It comes with 2 handles. I rarely lock more than one of them and have on rare occasions removed the one facing the tailstock for the reason you mention. Most of the time however I an simply extend the tailstock quill just a little further which moves the tailstock far enough away that i can still use this knob.

Re: Tool rest tightening handle?

#3

Steven Antonucci

Convenience vs. utility

steven antonucci

Because I cut with my handles low most of the time, I often find my handles bumping into the tightening bits on the banjo and the toolrest. I'm actually debating replacing them with a nut and leaving a wrench on the lathe.

Steve

Re: Tool rest tightening handle?

#4

Dick Hines

Re: Convenience vs. utility

Dick Hines

My 3520 came with two handles. There are 3 holes in the banjo. I only use the handle on the right I guess because I am right handed. One will hold the tool rest

so I can't see using both.

Re: Tool rest tightening handle?

#5

Re: Tool rest tightening handle?

Galen Vetterick

One of few benefits for a laft handed turner? Often wonder if there are any left handed turners who run a lathe in reverse and stand on the "back side" to turn? I'm not sure I can turn a bowl left handed, or right handed too sometimes.

Re: Tool rest tightening handle?

#6

Re: Tool rest tightening handle?

John Lucas

Galen I heard this weekend about a turner who had a Oneway specially built for left hand turning. He didn't tell me what the guy did however. At the time when I was thinking about it thought on the ONway all you had to do was run the lathe in reverse, turn the banjo around and possibly remount the swinging remote control so it was on the other side of the lathe. Then other than the spindle lock being a little awkward and the tailstock lock being on the inboard side it really wouldn't be much different. Would not work as easily on my Powermatic

Re: Tool rest tightening handle?

#7

Re: Tool rest tightening handle?

robo hippy

Those tightening handles are really set screws. I had one of the early PM3520A models, and it had only one set screw hole in it. The tool rest would constantly sink and pivot as I turned. I stripped the first handle (soft pot metal handle, not the screw) very shortly, and they sent me another. Same thing happened. I had a friend make me a T handle for it, and the cross bar of the T was in a slightly over sized hole so it would always drop down to be out of the way. I could really ratchet it up tight, but still had the same problem. Some use stop collars on their posts to keep it vibrating down. I never seem to be at the same height twice. I like it higher some times for when I hold the tools level, and lower some times for when I drop the handle. I do like the wedged banjo tightening system, which has small wedges on either side of the post when I tighten. With the 2 wedges, there is virtually no movement. Seems like the Oneway lathes did some thing different, like the set screw pushing a piece of metal into the post rather than just the set screw for a better hold. I don't think this part of the lathe is generally designed well.

robo hippy

Re: Tool rest tightening handle?

#8

Re: Tool rest tightening handle?

Galen Vetterick

I'm not sure I would really like my tool post locked any more than it is. I'm no expert turner so there has been a few time I got into trouble and a catch forced my tool rest down and hopefully brought the tool out of the way of the piece. I hate to think where the lathe tool may have went if the tool rest did not give first or maybe it could have been my arm first.

I have not looked at the contact end of the locking screw to see what shape it is in. I could see depending on it's style you might eventually damage a point or cup end and it would not hold as well if you force it too many times. Guess I will go look now just to see what shape it is. It does not seem to mar the tool post steel.

Re: Tool rest tightening handle?

#9

Re: Tool rest tightening handle?

Lloyd in Mississauga

My banjo had 3 holes for the adjustment handle; tail stock side, head stock side and then on the outside, near the lock down handle. Like Reed, I strip out a couple of handles under warrantee. I then replaced them with a third party option and I managed to strip out the threads in the banjo itself. Then moved the handle to another hole and off we went.

It was a bit awkward at first, but since the handle had a spring loaded locking mechanism, I could adjust that out of the way as needed.

Lloyd