Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Curse you Doug Thompson! (kidding)

Posts

Curse you Doug Thompson! (kidding)

#1

Curse you Doug Thompson!  (kidding)

Craig Daymon

Down in the shop trying to turn a multi-axis piece on the mini lathe, with the lathe tied down with rope to a workmate. My 5/8" Doug Thompson detail gouge (great tool) slid off the workmate and went point first right into an extension cord. There went the power, tripped the fuse, and trashed the extension cord. (Hence my curse upon Doug, no fault of his.)

I don't know who came up with this crazy idea of using sharp tools to turn. This never would have happened with a dull tool. :D

Re: Curse you Doug Thompson! (kidding)

#2

Better the cord than your foot!!


Re: Curse you Doug Thompson! (kidding)

#3

So did the sizzle and sparks do .....

JamieDonaldson

... any damage to the steel of the tool? ;)

Re: Curse you Doug Thompson! (kidding)

#4

Re: So did the sizzle and sparks do .....

Craig Daymon

Like it could have!

Made it about half way through the cord. Enough to cut the wires and short it. I also had the cord of my carving tool drooping in the same area. Glad it missed that. Extension cords are cheap and easy to find.

Re: Curse you Doug Thompson! (kidding)

#5

Re: Curse you Doug Thompson!  (kidding)

John Lucas

Craig I did the same thing about 8 or 9 years ago. What are the odds. I dropped some tool and it fell point down on the power cord for the lathe and cut some wires and shorted it out.

I've also had a skew fall off the lathe and stick point first in the arch of my foot. That was not fun.

Re: Curse you Doug Thompson! (kidding)

#6

Safety Issue?

Bill Howatt

I find this interesting especially since it has never happened to me. Over the years there have been posts on turning safety in various forums and I don't recall seeing anything written about the hazards of tools falling onto feet let alone power cords.

When you think about it laying sharp tools on the relatively narrow bed of a vibrating lathe or any other insecure area should be a no-no.

Bill

Re: Curse you Doug Thompson! (kidding)

#7

Re: Safety Issue?

Craig Daymon

Yes it is a safety issue. I usually try to park my tools in the holes located in the workmate, just didn't do it this time. Unfortunately, that doesn't work for skews, roughing gouges and hollowing tools. I have been wearing safety shoes in the shop lately with reinforced toes (2 pair, one steel, one composite), though more because they are close and not usually for safety.

That being said, the shoes would not protect my arch, like in John's skew accident and I'd hate to lose the use of my prehensile toes by cutting a tendon (kidding).

The other thing to consider is that the incident could have caused a spark and a fire in that very few of us have a clean floor around our lathes.

Might be good to invest in some of those cord strips, the ones that look like mini rubber speed bumps with a groove on the under side for the cord? They look to run about $2 per foot and sold in 5 and 15 foot lengths at the big box stores. "Wiremold" appears to be the brand at the orange and the blue boxes.

Also would be good to keep you from stepping on/running over the cords.

Might be cheaper from McMaster or Grainger, maybe even offering some heavier duty.

Re: Curse you Doug Thompson! (kidding)

#8

Re: Safety Issue?

Guy Bratt

I really dislike cords on the floor. To reduce that situation the cord for my PM hangs from the cieling. Also a 120v cord in the middle of the shop and one for the table saw. Most of my cords are throw aways from construction sites over the years. When I replace the cord caps I add a mesh grip to hang the cord from a screw eye.