Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

More Demo prep

Posts

More Demo prep

#1

More Demo prep

John Lucas

I always try to go through my demos if I can so I can remember all I want to tell the people. In this case it's also so I won't forget any tools or stuff. I turned a threaded gift ornament. Unfortunately this piece of wood was crappy. The bottom of the finial had a hidden crack and broke and had to be shortened. There was also a defect in the top right where the threads go so I had to shorten it which made the grain not match.

I also had a problem I've never had before. When screwed together to finish turning I could not get it apart. I guess the pressure from turning this hard wood and perfect fit of the mating surfaces caused it. I tried all the usual methods of various friction devices. I finally took a strip of 220 grit sandpaper and wrapped it around it. This gave me enough friction to break it free.

The other project is turning a platter with Hunter tools so I can show how they are used. This was a piece of old growth pine that I had. It came out great.






Re: More Demo prep

#2

Re: More Demo prep

Doug Adams

John

At times I have good luck with that rubberized shelf liner with square 3/8 holes rather than sandpaper and it has worked well.

Doug

Re: More Demo prep

#3

Re: More Demo prep

John Lucas

Doug I tried the rubber shelf stuff first. then some gloves I got from TEK that have high friction dots all over them. I wrapped some extension cord with high friction rubber around it. That has always worked to get stuck filters off cameras. My strap wrench wouldn't fit and I didn't want to try my vice grip chain wrench. Heck I even cursed at it. That always worked before, not this time.

Re: More Demo prep

#4

Mike Stafford

Use a bigger hammer.....

Mike Stafford

Hammers might not be the appropriate tool in this instance.

I was wondering about the origin of that blue streak I saw in the sky to the west of me. Now I know it was John Lucas trying to free up his stuck turning. :b

Nice ornament and a great job on the platter. Pine is not one of my favorite woods to turn.

Re: More Demo prep

#5

Re: Use a bigger hammer.....

John Lucas

I have a love hate relationship with pine. You do need sharp tools and good technique but it polishes up great and people like the look. Especially when you tell them it's just a 2x4 or scrap left over from building a house. The downsides, it dent's if you look at wrong and I really hate the knots with sap. Deep ones I seal with shellace, shallow ones I use thin CA.

Re: More Demo prep

#6

Re: Use a bigger hammer.....

Don Orr

I really like that platter John. I turn softwoods on occaision and have the normal hard time getting truly clean cuts. Does the Hunter cutter do this nice a job when properly used? Great surface there.

Re: More Demo prep

#7

Strap Wrench?

Craig Daymon

I've used one to free up a stuck chuck and some larger items. Not sure if I've used it on anything that small.

I have 2 (because they were cheap and I'd probably lose one...eventually both) and the ones I have have plastic handles and black rubber straps. They very useful tools to have around the lathe.


The plastic handled ones with the rubber straps are fairly non-marring, which is another plus for working with turnings. Also makes them the cheapest version.

-Craig

Re: More Demo prep

#8

Re: Use a bigger hammer.....

John Lucas

Don I used the Osprey for the final cuts and the only reason I had to use 220 grit were a few places where I didn't control the tool well enough. I'll call these tool marks, not torn grain or anything like that. I think If I had spun the wood faster these would have been gone. For some cuts in soft wood the tool cuts so easily it's too easy to push the tool and you get those tiny spiral lines that are easily sanded out. I also had an area out near the rim where chatter was evident. The rim was really flexible. I got rid of it by using the Osprey as a shear scraper. This may have been sanded out by 400 grit but since I already had the 220 for the middle of the platter I hit it with that first.

Used purely as a scraper with the cutter flat (I used the Hercules for this but the Osprey does the same thing) the center flat portion was very good with only very minor tearout. Would have easily sanded out with 180 grit. I went ahead and took another cut with the Osprey in bevel rubbing mode and cleaned it up.

Re: More Demo prep

#9

The problematic part of turning .......

JamieDonaldson

...pine, preferably when dry and not too sappy, is the sanding. It doesn't take much to sand away the soft early wood between the growth rings, and then the surface feels like corduroy! This platter of John's looks like he "done good!"

Re: More Demo prep

#10

Re: Strap Wrench? *LINK*

John Lucas

Craig I had 2 of those. Broke the small one the first time I used it. I guess it was worth what I paid for it. It was a harbour freight. I needed one smaller.

Here's what you need if you really get something stuck.


http://hand-tools.hardwarestore.com/67-396-locking-pliers/vise-grip-chain-wrench-600077.aspx?utm_source=PLA&utm_medium=cpc&utm_term=&utm_campaign=rkg

Re: More Demo prep

#11

Brad Vietje

Re: More Demo prep

Brad Vietje

Both are nice pieces, John. I gotta say, I'm not a big fan of turned Pine, but that platter sure looks great!

Have fun at your demo -- I'm sure they will get a lot out of it.

Safe spinning,

Brad Vietje

Newbury, VT

Re: More Demo prep

#12

Mike Stafford

All the strap wrenches you'll ever need.... *LINK*

Mike Stafford

Here is a link to Sears and all the different strap wrenches that they offer. I use the 2 piece strap wrench set in my box class. Sometimes when turning small cross grain boxes on screw centers the box body can be difficult to remove. The larger wrench will usually do the trick.


Strap wrenches

Re: More Demo prep

#13

Re: All the strap wrenches you'll ever need....

bill Crommett

We have two strap wrenches in the kitchen. I got them at an auto parts store . They are called "Oil filter wrenches" and for old folks they make removing glass can lids possible.

Re: More Demo prep

#14

Re: Strap Wrench?

Don in Central Illinois

That might mar your pine.

Re: More Demo prep

#15

Re: The problematic part of turning .......

John Lucas

That's why you use the Hunter tools so you can start sanding fine enough to not have a problem with the summer winter growth.