Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

Spindle adapter - 1"x8tpi to 3/4"x10tpi - ????

Posts

Spindle adapter - 1"x8tpi to 3/4"x10tpi - ????

#1

Spindle adapter - 1"x8tpi to 3/4"x10tpi - ????

Craig Daymon

I have a Oneway live center with its 3/4"x10tpi threads and a JET mini with 1"x8tpi.

I want to be able to cut those threads into a block of wood, then thread it onto the headstock of my JET mini and cut the shape I want (for example, half of a cup chuck). With it, I could make whatever custom shape I want for the live center. (I already have the tap.)

Penn State has an adapter to go the other way, 3/4"x10tpi to 1"x8tpi, but I'm looking for the opposite. Does anyone make one of these?

Thanks,

Craig

Re: Spindle adapter - 1"x8tpi to 3/4"x10tpi - ????

#2

Joe Bradshaw

Re: Spindle adapter - 1"x8tpi to 3/4"x10tpi - ????

Joe Bradshaw

Go to your local hardware or big box and buy a 3/4 x 10 tap. Thread it onto your live center. stick a nail or some type of pin in the hole used to lock the center. Wrap some tape around the pin and put the live center in your headstock and turn away. You may need a drawbolt to hold the center in the headstock.

Re: Spindle adapter - 1"x8tpi to 3/4"x10tpi - ????

#3

Re: Spindle adapter - 1"x8tpi to 3/4"x10tpi - ????

Galen Vetterick

I purchase 3/4-10 nylon lock nuts and epoxy them into the block of wood I want to turn. I first chuck the nut up and turn out the nylon insert so that it will seat proper on my Jet 1220 spindle as it needs that recess created by turning out the nylon just enough to clear the back of the spindle.

I put a pin in the live center to lock it from turning and just put it in the headstock and mount the block. Keep the tailstock up against the block till you have all your rough cutting done. Then make light cuts to shape your new wood center cone. The live center probably does not have threads to put in a draw bolt but if you are just making light cuts the live center will not slip in the morse taper.

Re: Spindle adapter - 1"x8tpi to 3/4"x10tpi - ????

#4

Re: Add a tenon ...

Doc Green

Craig, what I sometimes do is cut a small tenon (with shoulder) on the end of the blank that will be threaded, then, after the threads are cut, install the piece in a scroll chuck to cut the profile I want on the other side.

At other times, I will install the live center in the headstock spindle, use a pin to lock it, and then cut the profile.

I've also found that it's not always necessary to thread the fixture. Simply bore a 3/4" hole in the blank so that it will slip over the threads and seat against the bearing surface to the rear of the threads.

Re: Spindle adapter - 1"x8tpi to 3/4"x10tpi - ????

#5

Re: Spindle adapter - 1"x8tpi to 3/4"x10tpi - ????

John Lucas

Simply screw the wood you want on your live center. Then insert a nail or cotter pin through the hole in the live center that keeps it from rotating. Then put this into the morse taper of your headstock and turn it. Simple.

Re: Spindle adapter - 1"x8tpi to 3/4"x10tpi - ????

#6

I should have read the other replies, great minds


Re: Spindle adapter - 1"x8tpi to 3/4"x10tpi - ????

#7

Leo Cuellar

Re: Spindle adapter - 1"x8tpi to 3/4"x10tpi - ???? *LINK*

Leo Cuellar

I found one for you, Craig. Kind'o pricey though! I'm pretty sure these used to be more plentiful a year or so ago and way cheaper as well.


Spindle adaptor

Re: Spindle adapter - 1"x8tpi to 3/4"x10tpi - ????

#8

Re: Spindle adapter - 1"x8tpi to 3/4"x10tpi - ????

Craig Daymon

Not sure I'd trust the nail, but I like the cotter pin idea.

Thanks.

Re: Spindle adapter - 1"x8tpi to 3/4"x10tpi - ????

#9

Re: Spindle adapter - 1"x8tpi to 3/4"x10tpi - ????

Craig Daymon

Thanks.

That's actually in line with most of the spindle adapters out there. Best Wood Tools has a huge selection, which unfortunately does not include the size I want, and their "sale" price is $5 more than the one you linked to. Penn State's are quite reasonable at $17 to $20, again not in the size I want. They do have 3/4"x10TPI to 1"x8TPI. If they had the right size, I'd probably order it up just for this purpose. As is, I'll pick up a couple cotter pins as John Lucas suggested.

-Craig

P.S. I don't think I'll be buying a Ring Master, but I marked the site.