Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

those durn sphere turning jigs...

Posts

those durn sphere turning jigs...

#1

those durn sphere turning jigs...

Darrin Hill

yeah.. i know there are ways to turn spheres w/o a jig... but us liberal arts majors need all the help we can get...

and since my birthday is coming up... and i've sold a few bowls and pendants here and there, i was thinking of treating myself...

what do you think about the one at las vegas woodworkers emporium...

or the lindsey sphere turning one.. http://www.lindsaylathetools.com/sphere/specs/

or any others to consider?

lindey takes paypal.. which is easier for me... and cheaper... but im always wary of cheaper..

d

Re: those durn sphere turning jigs...

#2

Jim Barbour

Re: those durn sphere turning jigs... *LINK*

Jim Barbour

You might want to look at the Vermec. It has a screw advance and allows you to set the cutter for a sheer cut. It is a bit more expensive, but not a whole lot. Of course turning a pair of cup centers and learning to do it by hand is the least expensive way out, and likely the most satisfying unless you are doing production spheres or must hit a particular diameter exactly.


http://www.vermec.com/id44.html

Re: those durn sphere turning jigs...

#3

Mike Stafford

Homemade version....

Mike Stafford

This is a picture of a homemade sphere turning jig using a Hunter tool.

I don't have any details or dimensions but it obviously pivots around on a bolt and is adjustable in and out with a stop. The in and out motion is controlled by the big knob on the bottom which enables the fixture to slide toward the piece being cut.

I hope this helps.


Re: those durn sphere turning jigs...

#4

Re: those durn sphere turning jigs...

John Lucas

Darin I've been collecting information on them for years thinking I would build one. I haven't yet. Everytime I need a sphere I just turn it between jigs. That being said now that I'm retired I will probably build one sometime this year.

Of the ones I want to either copy or modify the Vermec is the best. I like the idea of the screw advance. I can't tell what kind of cutter they use.

The home made one Mike made is excellent. Mark St Leger brought a home made one that looks very much like the Lindsey but made out of wood.

I would use the Hunter Hercules as the cutting tool because it will leave a better finish than the scraper versions. The Lindsey looks like it might use a hunter style tool but I can't tell the angle the cutter is tilted. I'm not sure it matters since the tool is captured. Flat would not be good but a forward tilt of at least 15 degrees will work better.

Re: those durn sphere turning jigs...

#5

Alot of $$ to turn a few spheres...:)


Re: those durn sphere turning jigs...

#6

Re: those durn sphere turning jigs...

Fred Holder

I believe that I have all of the commercial ball turning rigs on the market. The two available here in the United States it the one made by Lindsley and the one made by Vermec in Australia and imported by Woodworkers's Emporium in Las Vegas. Both are good tools for making precision balls, such as what I use in making the Chinese Balls. Many years ago, I made one from 3/8 inch plywood and used two ball bearings to ensure the swing was true and smooth. The L shaped swinging part was made by laminating three pieces of plywood with the center piece 3/8 inch short leaving a 3/8 inch open area at the top. I then attached a piece of very hard wood on top and drilled and tapped a hole for the adjustment screw. For a cutting tool, I used a 3/8 inch Bedan. I sold that with the lathe that I had built if for. Either the Lindsley or the Vermec tool will do the job for you.

However, you do not need them if you're only making a few balls and they are not needed to be perfectly round or to a specific size.

Re: those durn sphere turning jigs...

#7

Re: those durn sphere turning jigs...

Darrin Hill

i want the biggest sphere i can make and i was wanting to do production ....

so thats why the jig..

Re: those durn sphere turning jigs...

#8

Where are you going to get the wood

John Lucas

Spheres turned out of green wood will crack like crazy. If that's what you want of course that's a good thing. It's mighty hard to find dry wood any bigger than about 4".

Re: those durn sphere turning jigs...

#9

Re: those durn sphere turning jigs...

Fred Holder

I believe that the Vermec jig will only turn spheres of about 5" maximum. I use it to turn 2-1/2 inch and 65 mm spheres for the Chinese Balls. The Lindsay jig will turn much larger. You will probably have to use laminated material to make larger spheres. The biggest I've made was about 6" out of some very dry wood. To keep them round and true, you will have to use dry wood, which probably means laminating your blanks.

Re: those durn sphere turning jigs...

#10

Re: those durn sphere turning jigs...

Marvin Stoltzfus

I have a brand new jig jig soon to go on the market. The name of the jig is "The Perfect Sphere Jig". The size capability is up to a 14" sphere if you have a 24" swing lathe but this tool can be used on any size lathe up to a 24" swing. This tool has quite a few unique features. The head is removable for when you want to use the tool rest and for set up. It is designed to make the sphere, part it in half, hollow both halves and glue it back together and still have a perfect sphere. The tool is made using bearings for a smooth and tight operation. We use the Hunter Carbide Cutter on the tool. Although my website is not complete it is www.Sphereturning.com and the tool will sell for $329.00 and that is for any size lathe. I have turned baseballs to soccer balls to basketballs.