Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Playing with Ukibori

Posts

Playing with Ukibori

#1

Playing with Ukibori

John Lucas

I played with this technique a long time ago and never did anything outstanding. Forgot most of what I learned back then so I thought I would start learning again.

This is the second attempt. For those not familiar with the technique, you stamp the wood (in this case I used a heart stamp I made) Then you sand, turn or shear scrape the wood down to where you can just see the stampings. Some will still be there, some will be flush with the surface and some gone. It's hard to get a consistent stamp depth. Then you steam or wet the wood to make the stampings swell up above the surface.

Based on the first 2 mirrors I made with this technique the wood species is going to be important. The first was maple and it was so hard it was difficult to get the stamps below the surface. The texture created by the raised hearts is very subtle. This mirror is made from Sassafras. the wood is much softer. Some places very soft. The stamp went in smoothly in some places, not as smooth in other and some areas went in quite deep and tore the fibers at the edges. You can see the difference in the swelling in the final product. I used a rag over the work with a steam iron to raise the grain.

I'm sure the type of stamp as well as the type of wood affects how well this works. I'll keep playing. I remember I had the depth problem before and made a nail with a washer soldered to it for my punch. The washer limited the depth so they stampings were very consistent. The dots still didn't raise to the same level but when you did the first turning to lower the wood all the dots were recessed to the same depth which helped. I may make one of those this afternoon and try it. I will need to reshape my heart stamp because it's too subtle on these mirrors.






Re: Playing with Ukibori

#2

Re: Playing with Ukibori

Craig Daymon

Hey John, this is a guess and it may be something you have already done, but I would suspect that you should round the edges of your punch as you don't want to cut the fibers when doing this, but simply depress them. Just soften the edges so they won't cut.

I've been meaning to try this as well. I recently had an Alder vase on the lathe that I didn't have tightened down correctly (came back to it couple days after finish sanding outside and it shrunk) and had it bounce off the lathe. I raised the dent out with some distilled water and it is barely noticeable now. It would be more impressive if it was a pattern I wanted.

Just a thought. Good luck and I look forward to seeing what you achieve.

-Craig

P.S. I'm going to try a heart shaped mirror with the little guy with his arms out and heart bursting from his chest like I previously described. My niece, the future recipient, only knows that it's a mirror (and will be pink) but insists that it have her name on it in fancy letters. If I use this technique for her name, she will be more impressed.

Re: Playing with Ukibori

#3

Re: Playing with Ukibori

John Lucas

Craig I did round over the edges of the heart. Might need to do it more. I'll reshape the heart so top is a little deeper. That way maybe it will stand out more in the stamped wood. Then try it on some different wood and see if the edges need to be rounded more.

Re: Playing with Ukibori

#4

Jim Evans

Re: Playing with Ukibori

Jim Evans

John, have you thought about angling the sides of the stamp?

Re: Playing with Ukibori

#5

Steven Antonucci

Is it not more common on end grain?

Steven Antonucci

I always thought it was better suited for end grain work? Wouldn't it be difficult to get consistent results in side grain? I've only tried it once, and gave up because of this...

S

Re: Playing with Ukibori

#6

Pressing instead of stamping?

Dave Staeheli

John, how about pressing instead, maybe with your stamp held in a drill press? Might be easier to get consistant depth or pressure?

Re: Playing with Ukibori

#7

Re: Is it not more common on end grain?

Dick Coers

End grain will not compress, or expand. Well not easily anyway.

Re: Playing with Ukibori

#8

Re: Pressing instead of stamping?

John Lucas

I was discussing that very thing with a friend at lunch. With the drill press I can very the pressure so that I can create the same depth in harder areas as in softer areas. Now of course I don't know what that will do to the raised bumps. I guess I'll find out because I'm going to try it.