Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

Drying Pepper Mill Blanks

Posts

Drying Pepper Mill Blanks

#1

Drying Pepper Mill Blanks

Tom Henderson, Gulf Breeze, FL

I have acquired some short logs that I am milling into pepper mill blanks, 3"x3"x12". I will coat the ends with Anchorseal. Should I rough turn the blanks round to reduce the size and drying time? Drill the center out? Or just leave them square?

Re: Drying Pepper Mill Blanks

#2

Re: Drying Pepper Mill Blanks

David Walser

Tom - Rounding the blanks will speed the drying process. So, too, will drilling the blanks. If you do drill the blanks, I suggest you drill them with an undersized bit. The hole is apt to go a tad oval as the blanks dry. DAMHIKT.

Still, unless you're pressed for time, leaving the blanks square works well. There's more "fudge factor" available in mounting a square blank than one that's been rounded and drilled.

Good luck!

Re: Drying Pepper Mill Blanks

#3

Mike Stafford

Re: Drying Pepper Mill Blanks

Mike Stafford

Usually one should allow 1 year per inch of thickness plus a year for air drying wood. If you need 12" then I would cut my blank 14" to allow for some end grain splitting that is more than likely to occur. I have never tried drilling out the center for peppermill blanks but that should expedite the process. Like David said I would use an undersized bit to allow for the distortion that is certainly to occur.

Re: Drying Pepper Mill Blanks

#4

Steven Antonucci

so how do you redrill an accurate hole later? 


Re: Drying Pepper Mill Blanks

#5

Re: so how do you redrill an accurate hole later?

Don in Central Illinois

Very carefully!

Re: Drying Pepper Mill Blanks

#6

Re: so how do you redrill an accurate hole later?

Dale Miner

Unless your needs require getting the blank dry enough as soon as possible, I would leave the blank undrilled. If there is figure in the wood, and the blank drys with a curve or kink, when redrilling, the bit will follow the previous no longer straight hole. If the blank is straight grained, then drilling to speed up the process is OK.

Depending on the wood, two years is generally enough for a pepper mill blank. There will be perhaps another 1% shrinkage after the the blank is turned, but for practical purposes, it will not matter. Just make sure to fit the knob tennon on the loose side with wood that is less than completly seasoned. Woods that fall into the 2 year class are maple, walnut, and cherry. Oak, hickory, hedge, and locust need a longer drying period. I've never predrilled, but have pre rounded. My guess is that predrilling would cut the drying time in half.

Re: Drying Pepper Mill Blanks

#7

Re: Drying Pepper Mill Blanks

Dick Coers

I was going to give you my hint for free drying, but I see you are in Florida. For everyone north, I put my blanks on top of the main furnace trunk line. Figured woods start at the far end, easy drying woods can start up by the furnace. It's a real gentle dry since the wood heats up and cools with every furnace cycle. It doesn't get hot enough to kill bugs, but the wood dries very quickly. Rotate the stock through the winter so everything ends up getting the most heat by the furnace. Raffan drills out the center to quickly dry box blanks. It will dramatically decrease drying times and stress movement. The attic is a good place in the summer. It does get hot enough up there to kill bugs.

Re: Drying Pepper Mill Blanks

#8

Steven Antonucci

I am waiting for someone to say a reamer. 


Re: Drying Pepper Mill Blanks

#9

Re: Drying Pepper Mill Blanks

Tom Henderson, Gulf Breeze, FL

The attic! Didn't think about that, our attic stays warm most of the winter.

Re: Drying Pepper Mill Blanks

#10

Re: I am waiting for someone to say a reamer.

Dale Miner

While at first glance the long length of a reamer sounds like it would clean up an out of round and non straight hole, the ability of a reamer to remove stock is very limited. The flutes would rapidly plug.

Re: Drying Pepper Mill Blanks

#11

Steven Antonucci

Or does the hole need to be centered?

Steven Antonucci

It's a peppermill. Does it matter?

S

Re: Drying Pepper Mill Blanks

#12

Re: Or does the hole need to be centered?

Dale Miner

Steve,

You brought up use of a reamer, so my comment related to the difficulty of trying to use a reamer to clean up a predrilled hole.

As far as centered, my method of final turning involves mounting the mill body between centers on the hole in the body, so the hole ends up centered. If the hole were not centered, the tennon on the knob would cause the knob to be off center. Most mill designs would suffer in appearance if the knob was not centered on the body.

If the hole was not fairly round, then that method would be dififcult as the mounting could shift about while being turned, causing the OD to runout if shifting occurred during turning. If the hole in the body is not square, then the knob to body joint will have a poorly fitting faces with a visible gap on one side. If the hole was not fairly straight, then the shaft would cause the ginding mechanism to either bind or run an an angle and not grind as efficiently.

Re: Drying Pepper Mill Blanks

#13

Re: Drying Pepper Mill Blanks

Joe Herrmann

I asked Paul Chilton from Utah this same question. He told me to cut the blanks a bit longer than necessary and then turn them round and coat them with Anchorseal. I did that with a bunch of blanks several years ago and have had no splitting. I figure that once you start getting a bit of stock built up you don't have to worry about drilling them out beforehand so I didn't.

Re: Drying Pepper Mill Blanks

#14

Re: Drying Pepper Mill Blanks

John Lucas

Tom I've found the year per inch is far off here in Tennessee. That is if the wood is already cut into something like a pepper mill. I don't turn pepper mills but do save a lot of stock that size for boxes and spindle blanks. I've also been experimenting with saving thick platter blanks.

I coat the ends with Parrafin wax. I use an old electric skillet to melt the wax set at a temperature just barely warm enough to melt the wax. WAx has a flashpoint of 480 degrees so you don't want it anywhere near an open flame. It melts at about 160 so your plenty safe. Still a good idea to do this outside and keep the metal lid handy.

2 good thick coats of Anchorsel seem to work almost as good. I start them out on the floor of my shop and after a month or so move them to high shelves. Within 6 months or so a 3" square blank is down to about 13% which in Tennessee is pretty much dry. I do sometimes get some wood movement so I usually leave them longer for boxes.

turning them round does speed up the process but not a whole lot. turning them round and then boring them really speeds the process. To recenter and drill mount the wood between centers using a cone inserted in the hole on the tailtock and a drive center. turn a tenon on the drive end for your chuck or simply true up the one that was there. Mount it in a chuck and then you can redrill the hole. I would use a mandrel to turn the outside after that because the drill may not run perfectly true.

Re: Drying Pepper Mill Blanks

#15

Re: Drying Pepper Mill Blanks

Tom Henderson, Gulf Breeze, FL

Thanks John, and to all that responded. I did not originally mention that the log sections are from an standing oak that was dead, and are partially spalted. I don't have a moisture meter, but the wood seems to be drier (lighter) than freshly cut green oak.

I am still considering placing some in the attic, but I will also have some in the shop.