Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

nova dvr xp

Posts

nova dvr xp

#1

nova dvr xp

Darrin Hill

WHen you turn on your nova, there is an auto default speed of 500...

Is there any way to change that? I read the manual and the latin is greek to me... (liberal arts major)..

I started a piece of elm today and it seemed that the torque was a little soft, cause my piece was cut with a chainsaw and had corners, and when it hit a corner it seemed to want to slow and not hit as hard... usually when i hit a corner it hits with a certain amount of 'whack'.. tonight it was more of a dull thud.. and i usually start at around 100-125 rpms just to rough out the corners..

it also took its time slowing down whenever it did catch.. i'm not sure how it works, but if you get a dig you can somemtimes stop the spindle and when you let go all that pent up force has to go somewhere... so it can go from a speed of 100 to 400 as it unwinds, but it slows back down to the 100... not sure how or why that works, but...

but when i did catch, it went up to 400 and took its time slowing back down to normal. It might have been because the piece is out of balance, but im a photographer, not an engineer..

so i unplugged, and took off the control cover and blew a bunch of dust out... i put it back on, plugged it in and turned it on and the auto speed was now 110 instead of the 500.. i might have accidentally changed it if its possible to do so because i was wondering if there was a mode for changing the amount of torque,.. so i pushed mode ... i think that was all i pushed...

and the manual said if you pushed mode while running it would do a diagnostic... and mine didnt do anything..

so then i came in and tried to read the manual online and it didn't seem to cover my issue.. i went back outside.. increased speed to about 250 and everything seems happy now... forgot to check the default speed after i turned it off...

just wondering..

i'd call teknatool but its saturday and they have the worst customer service anyway... so I'm just going 'hmmm'....

Re: nova dvr xp

#2

Re: Removing the corners ... *LINK*

Doc Green

Hey Darrin,

I don't know anything about the DVR, but I would suggest a different approach to removing the corners from the blank. Any time you hear whack, whack, whack, or thud, thud, thud, that is bad, bad, Bad! That puts a big strain on everything . . . the tool, tool rest, the lathe, the mounting system, and You!

Don't approach them head on. Work at them from the side. Initially, set the tool rest at 45 degrees near the tips of the corners on the tailstock side. Then nibble away at the corners with very light cuts to get started.

As you progress, work more toward the tail center (using tailstock support, of course) until you get an area that is round. Then, as you deepen this area, you can work more toward the headstock and around the side of the blank, removing the corners a bit at a time, from the side. This way, the corners present much less of a problem.

You can see pictures of this in the article at

http://www.docgreenwoodturner.com/gouges6.html

A similar technique is described on a practice blank in the article that comes before this.

Good luck, and be careful. Approaching the corners head on is very dangerous, in my opinion.

~Doc


Article on Doc's website.

Re: nova dvr xp

#3

Re: nova dvr xp

Jeff Willaford

Listen to what Doc said. I think you'll find it a much easier process than whacking away at the corners.

The power up setting will always default to 500 rpm according to the manual. I don't know what you are seeing that is 110. And yes, there is a way to change the torque settings but most DVR owners I know of, including myself, use the factory defaults without an issues. The manual (page 18 in my copy) is pretty clear on how to change between factory settings but I've not found a need for other than Normal with my turning.

1. SOFT: For light work at speeds lower than 500 rpm

2. NORMAL: Suitable for most work and is the default setting

3. HARD: For heavy and/or ‘out-of-balance’ work at speeds lower than 500 rpm

Re: nova dvr xp

#4

Re: nova dvr xp

Ralph Lindberg

Darrin

Trouble-shooting via a post is tough but the following occur to me

*If this is a change in performance there may be an issue in your control electronics.

*Cleaning your electronics of dust is a good idea, all people that own electronic controlled lathes should do this periodically (hobby turners once a year)

*When you talk about removing the electronics, did you remove the controller or open the lathe up and remove the mother-board?

*Are you certain you got the ribbon cable(s) back, exactly right, with no broken pins

*It is possible to change the power-on default, but I don't recall the procedure right now and suggest that the 500 is really a good "default" speed, it has saved me a couple times now

*Are you a member of either Teknatool user groups (Yahoo-Groups or MyFamily), if you are on Facebook, have you "liked" their posting there. It is possible to get assistance from other owners on all three areas.

Given your issues, and assuming you got the electronics re-assembled correctly, my guess is you might have an issue with the electronics.

Last, Tektnatool this week announced they were looking for two "turners" for part-time employment at their Florida facility. Duties would revolve around answering customer inquiries.

With the DVR motor now being used on the Shopsmith Mark-VI, I would not be surprised their customer base is growing.

Personally I have had good responses from Teknatool, including calls from the factory in NZ.

Re: nova dvr xp

#5

Jim Barbour

Re: nova dvr xp

Jim Barbour

Hi Darrin ~

First off let me second (or third, or whatever) Doc's admonition to NOT come at the corners square. That's a quick way to damage your lathe and hurt yourself.

The XP speed will start wherever you left it, if you don't switch off the toggle. It also has five pre-set speeds, four of which you can set. As you go "up" from speed one the second is no more than 500 and it is not selectable upwards (it can be set slower, I think). The other four can be anything you wish, and are pretty easy to set - see the manual, page 29 (the salient part is copied below). I currently have mine set to 3500, 500, 1000, 1700, 2500 for spindle work. When I am turning 50 or so small acorns I turn at 3500, texture and sand at 500 so having those next to one another is handy. When I am doing larger work or bowls I set it to 250, 500, 800, 1200, 1700 or some such.

From the Manual:

==============

Programming the Favourate Speeds

29 115-0701-001

Press the "Mode M" key , hold it and press UP or DOWN RPM in order to go from one preset speed number to the next one.

Pick a preset number you would like to change. IMPORTANT Note: The default speed (#2D) can not be set at more than 500 rpm and the saved preset speed values will work also after Hard Reset Function.

Press the "SELECTOR E" key in order to make the request for saving the new value of pre-selected speed in the EEPROM (memory). It will display the symbol ‘?’ at the end of LCD line.

Change to the speed you require by using the UP and DOWN arrows.

Press the key PROGRAM P to store the new value. There will be the symbol ‘*’ instead the symbol ‘?’.

Your new setting is now stored.

===============

If you want to talk through it, send me a private note and we'll set up a phone call.

Re: nova dvr xp

#6

Re: nova dvr xp

Ralph Lindberg

PS

At speeds below 250 the available power drops way off. I usually don't "turn" below 250

Re: nova dvr xp

#7

Re: nova dvr xp

walta

First I start your cut near the tail stocks center, make a make a ring to work from.

I have found that if you stall or nearly stall a DVR you can confuse it brain and will need to reboot it.

Next with most motors 120 to 240 volt conversion will not change it horse power at all. The DVR is an exception I do not recall the numbers its about 20% mostly in the low end torque and well worth the effort.

Walta

Re: nova dvr xp

#8

Re: nova dvr xp

Ralph Lindberg

The problem with converting the DVR-XP to 220 is now you should get a 220V surge system. I have to say I am the only person I know that has one (built into the main breaker panel)

Any one that runs any digital controlled lathe, with out surge/spike protection is running a very expensive risk.

About 20 years ago we had, well a MASSIVE spike/surge during a storm, to the point where a couple light bulbs blew up. I lost radios, tvs, etc. This was with a couple surge arrestor strips. Over and above that, during the regular winter power outages I would lose "something" every winter.

I then added the main-panel surge system and bought new strips. I haven't lost a major item since.

Re: nova dvr xp

#9

Re: nova dvr xp

Darrin Hill

sorry.. for some reason i hate reading manuals..

they, especially this one, doesnt make sense to me...

I litterally need to be shown how things work by another person.... Some people think it's the ADHD.. i have several members in my family who do the same thing.

It's why i ask so many basic questions here,

Like.. that part on page 18 does not (as far as i know) ever mention the word 'torque', and if it doesnt mention it, it has nothing to do with it. I cant make generalizations.

I dont like watching videos cause i can't ask questions, get them to stop, and show me what they're talking about..

yeah.. i know.. people think i make this up.

Re: nova dvr xp

#10

Re: nova dvr xp

Darrin Hill

i just took off the outer cover and the aluminum plate... didnt unplug anything..

on the speed control input panel thingy.

it took me 3 weeks of back and forth phone calls and emailing corporate offices and talking to their US manager to get them to send me a part. Most of the phone calls and ALL of the emails were ignored. I had to call woodcraft to get in touch with whoever buys stuff from teknatool to call them to telll them how mad i was gettting, because teknatool ignored me.

Re: nova dvr xp

#11

Re: nova dvr xp

Mark ravensdale

I often turn on my dvrxp in the rpm range of 200-300 with no problems, however I only really drop below 200rpm if I am applying a finish of some sort, I too never mess with the torque settings as I have found the pre-set one to work just fine, also remember that the lathe is able to alter some of its setting by somehow knowing if you have an out of balance work piece mounted on it (I know this by first mounting a nice true blank starting the machine for a few seconds then stopping and checking the settings then mounting a badly out of balance blank starting for a few seconds then stopping and checking the settings again and low and behold they had altered, how it does it I don't know but it does!!!)

Re: nova dvr xp

#12

Re: nova dvr xp

Mark ravensdale

Maybe that's why I can turn in the rpm range of 200-300 with no problems, I remember reading somewhere that the dvr motor puts out more power (20%???) when using 220-240 volts,

I must admit that I have never managed to scramble the computer by stalling the motor though, having said that I think I have only ever stalled it 2 or 3 times in the whole time I've had it (2-3 years) and that was because I was trying to take a monster cut with a 3/4 inch gauge, overall I have found torque to be VERY good and bearing in mind most of my work is done belowe 1000rpm

Re: nova dvr xp

#13

Re: nova dvr xp

Mark ravensdale

I live in the UK and I run ALL my equipment off surge protectors, I learned an expensive lesson several years ago when I lost 3-4 thousand pounds worth of computer equipment to a surge!

Re: nova dvr xp

#14

Re: nova dvr xp

Jim Breeden

Speaking of XP's. Does anybody else have a "growl" at less that 500rpm? I've been to all kinds of Nova sites, listened to their XP's and, they seem to also growl.

Re: nova dvr xp

#15

Re: nova dvr xp

Darrin Hill

whenever i have a piece with corners, i always start at 100 just to knock off the edges... however i will next time try from the tailstock... my problem is if the bark side is on the tail stock the surface is usually as uneven as the corners... cause of bark, voids, etc..

This piece was a bit more pointy in it's corners... and not very balanced ...so it MIGHT have been auto-torquing..

but it does start at a default of 110.. i will TRY to email teknatool and see if they think it was acting weird because of the shape..

and i cant hear mine growl cause i have a radio blasting out classic rock..

Re: nova dvr xp

#16

Re: nova dvr xp

Mark ravensdale

Not heard a growl as such but sometimes can get a slight noise when the lathe is trying to keep spindle speed while freewheeling (no load applied/no cut being taken) is this what you mean ???

When I first got my dvrxp I was very surprised how quiet the motor ran as compaired to the other lathes I had used previously, also I was very impressed with how the lathe increased/fed in power as a big deep cut was being taken, it was seamless (no steps)

Re: nova dvr xp

#17

Re: nova dvr xp

Jim Breeden

It does make noise when freewheeling, primarily at low speeds >500. Kinda like (don't laugh everybody :D ), r-r-r-r-r-r-r, knowing it's difficult to describe without sound. I wonder if this is common with motors of this type. Emailed Teknatool twice, never received a response, Fl and NZ both. Watched as many videos as I could find with the XP, turned up the sound, could "almost" hear some kind of sound but, couldn't determine if it was the same. Other than this little annoyance, I wouldn't trade my XP for anything.

Re: nova dvr xp

#18

Re: nova dvr xp

Mark ravensdale

I think what the other posters are trying to say is to try and avoid those cuts that cause that heavy bumping/banging of the tool, it's much better to come at it from the side (or 45degrees) kind of hard to explain what I/they mean but once you try it you will think "why didn't I do this before" having said that there will no doubt be occasions when you have to do it the harsh way

Also, your not alone when it comes to having difficulty understanding/picking things up, I too am a little bit like that, when I first started turning I got myself several turning books, but learned very little from them, then I got some woodturning videos and learnt more from one video than I had learnt from ten books

Keep at it, practice is the key!!!

Re: nova dvr xp

#19

Re: nova dvr xp

Jeff Willaford

I've had my XP growl but it only happens IF I have an out of balance piece between centers AND the drive spur has lost it's bite on the wood. The growl goes away when the drive spur is well seated. I've also switched to a much larger spur with a better grip. That solved the growling for me.

Re: nova dvr xp

#20

Bark side

Bill Howatt

Even if it is uneven, bark is very soft compared to corners especially corners that are causing you to cut off end-grain. Just approach it carefully near the center and in a couple of cuts you will have a nice smooth reference to proceed up the bowl.

It is well worth your time to make some effort, and it won't be very much, learning this technique and overcoming your aversion to it. Whacking corners is hard on the machinery, your body and you run a risk of breaking cast-iron tool rests if you hit the blank's corner when the tool isn't firmly sitting on the rest.

Incidently, this technique also makes turning the bowl faster because you are shaping at the same time as you are removing corners.

Bill