Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

Softening epoxy to realign

Posts

Softening epoxy to realign

#1

Softening epoxy to realign

Craig Daymon

I turned a prayer wheel recently. Unfortunately, I epoxied in the steel shaft and failed to insure it was perpendicular to the lid into which it was glued. I'm wondering if I can somehow temporarily soften the epoxy so it can be realigned.


I'm considering a short coil of nichrome wire around the shaft, heated using my woodburner (for which I have a handle that will take wire).


I should have closed the box, which would have insured alignment without impacting the curing.


There is a rare earth magnet in the handle below the bronze bearing that holds the shaft in place when it is all together. Getting this aligned would allow the lid to close properly.

Woods are Irkok(maybe), Masur Birch and Ebony, maybe African Blackwood.

Thanks for any help,

Craig

Re: Softening epoxy to realign

#2

Re: Softening epoxy to realign

Galen Vetterick

Before you try the heat put the piece in the freezer. The epoxy will become brittle and the shaft will shrink at a different rate so with a little force you should be able to break the bond. Since the piece looks finished I don't think I would try acetone as it would need to soak in well. Actually make the fibers soft to remove the steel/epoxy.

Re: Softening epoxy to realign

#3

Re: Softening epoxy to realign

John Lucas

Heat works just fine and it doesn't take very much. I used to install and remove inserts in recurve bows. The were glued in with epoxy. I would simply screw in a short bolt, heat the end of the bolt with a propane torch while pulling on the bolt with pliers. It would pop right out with very little heat and no damage to the wood.

Re: Softening epoxy to realign

#4

Re: Softening epoxy to realign

Craig Daymon

I tried the freezer, but it didn't work. Possibly because I was apprehensive about using too much pressure and where the cracking would result. I did hear some, minor, cracking, but I wasn't confident whether it was the wood or the epoxy.

I'll try the heat using the nichrome wire like I mentioned earlier. That should let me apply the heat without the need for a flame. (My shop is not all that safe for turning, let alone open flames.)

I'll post the results.

Thanks

Re: Softening epoxy to realign

#5

Re: Softening epoxy to realign

John Lucas

The internet is so funny. I did a search for softening epoxy and found lots of answers that say heat won't work. Most of these were from Forum's and were obviously just opinions from "experts". As mentioned above I do this all the time and it works.

I found this PDF from a commercial site. I don't know how to download the whole PDF so I just copied the important data.

A major advantage of using an epoxy is that it provides a very strong, permanent bond in adhesive applications. This perma- nence can also act as a limitation when needing to rework, remove or “decapsu- late” the cured epoxy. This document lists several techniques which have shown to be effective tools in removing cured epoxy from substrates.

1. Chlorinated solvent is the most aggres- sive way to attack cured epoxy. Methylene chloride (dichloromethane) has shown the most success but does require the material to be soaked for several hours. Stripping Agent MS-111 (which contains approxi- mately 85% methylene chloride) from

the Miller- Stephenson Chemical Co. in Danbury, CT is a product that works very well. Dynaloy LLC also has several epoxy solvents and removers based on which type of epoxy hardener is used in a product.

2. A warm solution of sulfuric acid will dissolve the cured epoxy. This, like the chlorinated solvents, also requires a good soaking. An effective technique that some customers have used is repeatedly dropping the acid on the top surface of the epoxy to facilitate the removal.

3. Other chemicals which have shown to be effective: toluene, NMP (n-methly- pyrollidone) and MEK (methyl-ethyl- ketone).

4. Combination of heat and pressure. Since epoxies are thermosetting resins, they have a softening point called the glass tran- sition temperature (Tg). Heating above the Tg will soften the material slightly and allow the epoxy to be pried away more

easily. The tip of a soldering iron can be used as the heating mechanism and can be applied directly on the epoxy or at the bond line. When the adhesive becomes soft and “gummy”, de-bonding can occur. Heating of the substrate using a hot plate is another common technique, as well as using a conventional box oven.

5. Degradation temperature of the epoxy. Most epoxies will decompose and turn to carbon ash at temperatures of 400°C and above. By heating the unit above the deg- radation temperature (found on the data sheet), the epoxy adhesive simply burns away.

6. Boiling water. Epoxies, when exposed to boiling water for an hour or so, will lift away from any surfaces in most cases. Some prying action may be needed and this technique can vary widely depending on epoxy and bonding surfaces.

7. Thermal shock. Large differences in thermal expansion rates between a sub- strate, adhesive or component can stress the epoxy and create joint separation as well as bond line lift. Thus, by impos- ing severe thermal fatigue on the adhesive joint, de-bonding can be accomplished simply by the thermal-mechanical differ- ences of adhesive and substrate.

Several of the techniques listed are destruc- tive in nature and can be suicidal in terms of re-usable parts for manufacturing. This document makes no attempt to suggest how manufactured parts can be saved

or reclaimed. Its intention is to provide means of solving erroneously placed epoxy or components, and failure analysis.

Re: Softening epoxy to realign

#6

Re: Softening epoxy to realign

Emmett Manley, Lakeland, TN

Anyone who has changed the shafts in their golf clubs knows that an epoxy bond can be softened by a little heat from a small torch. This allows separation of the club head from the shaft or minor realignment of the club head. As John said, it does not take much heat.

Re: Softening epoxy to realign

#7

Re: Softening epoxy to realign

John Lucas

Emmett I changed my golf clubs to a bow. I can actually hit something with a bow. :) Well now that I think about I'm pretty good at hitting sandtraps and water hazards. I can also hit the only tree in the fairway, 200 yards away and it's only 8" in diameter. I guess I am a pretty good shot with a golf club after all.