Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

Glue up suggestions

Posts

Glue up suggestions

#1

Glue up suggestions

John Lucas

I'm going to start making these fan type segmented mirrors again. Glue up has always been a nightmare. I use to glue them up all at once with a little jig I made with dowels and wedges. Force everything together and then drive in wedges between the dowels. It was always a nightmare, mostly because everything is wedge shaped and slippery with glue.

Last night I glued these up in pairs using the same sort of dowels with wedges and some clamps. Less hectic but very slow since I had 3 seperate glue ups.

I'd like to come up with a better way. If anyone has any ideas or techniques they've used for something like this I would appreciate seeing it.

I'm leaning toward making a jig with angle iron as a sort of frame. I'll put bolts through the angle iron so once I get all the parts inside with glue I can sort of tighten each bolt until it pushes the parts into alignment and forces them together so the glue joint is tight.

Re: Glue up suggestions

#2

Re: Glue up suggestions

charlie belden

You want to control the perimeter of the glue up for clamping. By having your inlayed strips extend out past the perimeter of the body of the blank you lose that perimeter control. If you were to trim the length of each inlay to remain inside the blank's perimeter, BEFORE the glue up, you could control the perimeter of the blank. You'd slightly reduce the "turnable to round part" of the resulting blank, but save yourself some glue up time - and frustration.

Re: Glue up suggestions

#3

Re: Glue up suggestions

John Lucas

Charlie It's very difficult to control those pieces because they slide so easily. It's also hard to cut them to length because your trying to flex them into a curve and measure.

ONe other problem is because I make a single thin cut through the body the edges never come out perfectly flat and square because I make the veneer different sizes than the kerf. I have done them similar to Celtic knot where the saw cut is the same width as the veneer but that severely limits by my veneer thickeness. I use the scroll saw instead of the bandsaw but either one only gives me one thickness of kerf.

I was thinking that I could have one bolt per section in each direction. That would give me precise control to push each section in where it needs to be. It would also take the worry out of having the veneer strips longer than the kerf.

Re: Glue up suggestions

#4

Merle clamps?

Dave Staeheli

By no means the silver bullet, but when I make glue ups for my "straight fan" mirror blanks, I've been using those Merle band clamps from MLCS. I expect the same on your "curved fan" you have the same problem that the pieces want to squirt out the large end. Possibly 4 short boards around the blank, wrap in a Merle clamp, then wedges on each individual strip? Advantage is that one glue up for each clamp, so multiple glue ups at once. And they can be moved off the work bench while curing.

Re: Glue up suggestions

#5

Re: Merle clamps? *LINK*

John Lucas

Those might work but they sure are Pricey. I would be concerned that the side pieces would slip out since it clamps from the corners. Of course with straight line fan shapes you could also easily measure the length of the veneer pieces. I used to make the straight ones many many years ago. I was showing someone some photos of my early mirrors and the lines were all straight. I had forgotten.


http://www.mlcswoodworking.com/shopsite_sc/store/html/smarthtml/pages/merle_clamp.html

Re: Glue up suggestions

#6

Keith Tompkins

Re: Glue up suggestions

Keith Tompkins

John, one thing you could do is make the parts out of 8/4 material, then bandsaw down the center to get two mirror blanks.

Re: Glue up suggestions

#7

Re: Glue up suggestions

John Lucas

Good suggestion. I've done that before with other blanks. It's just hard to find good wood that thick and milling the veneer is more difficult. Veneer up to 1" thick I can cut pretty accurately on the table saw. Much thicker and it gets hard to control. I've cut it on the bandsaw of course but then you have to sand it which gets to be a pain.

Re: Glue up suggestions

#8

Extra jaws

Dave Staeheli

Forgot, been awhile since I made these. I have extra sets of jaws (even more pricey!) so I get more pressure points and avoid the corners. Works, but not great. Love to find a better way to do this.

Re: Glue up suggestions

#9

Re: Glue up suggestions

Barry Irby

How would it work to not cut the walnut blank apart, but route 1/8" lines into it about half inch deep and insert maple or holly stringing into them?

Or, cut the walnut blank apart, but then pattern route the pieces so that the gaps are accurate and leave you 1/8" spaces. Then you could make up a sturdy three sided frame, Bottom and two sides, and then lay up the glue up in it, using clamps to pull the top into the frame as if they were wedges.

Re: Glue up suggestions

#10

Re: Glue up suggestions

John Lucas

Barry done that. It's nice but looks a lot cleaner on the outer edges when the contrasting wood goes all the way through.

Re: Glue up suggestions

#11

Re: Glue up suggestions

John Lucas

Here's what I'm thinking might work. I just spent an hour on the phone with Canon getting the scanner to work on my new printer. Screw all the angle iron down to a piece of formica covered wood that I wax real well. I'll have to come up with an easy way to adust the screws. I'm thinking that I'll use Square or hex drive screws and then make some metal pads to go on the ends like C clamps have. Then I could use a power screw driver to speed up screwing them in.


Re: Glue up suggestions

#12

Keith Tompkins

Re: Glue up suggestions

Keith Tompkins

John, when I was doing segmented stuff, I bought my veneer, then added three layers, usually white/black/white. Easy to cut with a knife, and looks great..any width. When I did my "dancing tops", I used home-built clamps of wood and small bolts and nuts to keep everything in alighment, to prevent movement.

Re: Glue up suggestions

#13

Re: Glue up suggestions

John Lucas

Keith I do have a selection of veneer that I use occasionally. I do like to cut my own because it lets me match the species I want.

Re: Glue up suggestions

#14

Keith Tompkins

Re: Glue up suggestions

Keith Tompkins


Re: Glue up suggestions

#15

Toilet seat bolts?

Dave Staeheli

For clamping screws, how about nylon toilet seat bolts? Maybe wouldn't need pads at the ends. Or reversed counter-sunk bolts?

I think Keith's idea has merit, but then couldn't have any veneer sticking out.

I also think the bottom could be fixed without clamping screws or other.

Re: Glue up suggestions

#16

Keith Tompkins

Re: Toilet seat bolts?

Keith Tompkins

Hi Dave, I was thinking that, but there's really no reason for the veneer to stick out....the circle cuts it all away..

Re: Glue up suggestions

#17

Re: Glue up suggestions

Doc Green

John, here's an idea that I would try. But first, let's number the segments, starting clockwise from the lower left corner, which will be segment 1. Then, the segment at the lower right corner will be segment 10.

The idea is to clamp segments 1 and 10 into position so they can't move downward (looking at your picture) or apart horizontally. Then fill in the rest of the segments and veneer strips, with glue, of course.

Now, if you force segments 4, 5, 6, and 7 downward (...your picture), that will automatically put clamping pressure against all the surfaces. This could possibly be done with only one clamp if a piece of wood is made to push against the tops of segments 4, 5, 6, and 7. Something will have to be provided at the bottom for the clamp to work against.

Depending on the slickness of the whole assembly, segments 2 and 9, and segments 3 and 8 may tend to squeeze out of the pack. That is, segment 8 may tend to move toward the upper right. This movement will have to be restrained in some manner, such as by placing another clamp across the pack from segment 3 on the left to segment 8 on the right.

Get the idea? Now all you have to do is come up with a simple way to hold segments 1 and 10 in place, push downward on segments 4, 5, 6, and 7, and keep segments 2, 3, 8, and 9 from squeezing out of the pack. Shouldn't be too hard, but I'll leave the details to you.

Good luck! ~Doc

Re: Glue up suggestions

#18

Re: Glue up suggestions

John Lucas

Doc That's a good idea. I think the jig I described would sort of do that. I could leave the bottom 4 corner screws adjusted more or less permanently and then squeeze the other pieces in as you describe. Of course in reality all my mirror blanks are not exactly 5 1/2" square. Pretty darn close, and maybe the tapered pieces would take up the slack but if I use the bolts then they could be adjusted slightly.

If I was only going to make one or two of these 4 dowels put at the bottom corners and a clamp on top with a piece of scrap wood with notches cut where the veneer might stick though would probably work. Then one more clamp going side to side on the top to keep those corners pulled in tight.

Re: Glue up suggestions

#19

Re: Glue up suggestions

Scott Blundell

I was picturing your bolt idea before I saw it. I would suggest inserting bolts backwards (head to apply pressure) and cutting flat or phillips slots in the ends to tighten. That would simplify it some.

Re: Glue up suggestions

#20

Custom made clamping cauls?

Don Orr

Like you might use to clamp dovetails where the pins & tails are slightly proud of each other. Maybe fixed corner blocks at the bottom 2 corners, shop-made cauls on either side and one across the top. Clamp the sides a little, then pull the top down into the rest a tightten the sides. Clear as mud? Gaps in the caul for the veneer pieces-might need to trim their length a little. Wish I knew how to draw it and post it.

Re: Glue up suggestions

#21

Re: Custom made clamping cauls?

John Lucas

Don I got you perfectly. The dovetail cauls are what made me think of the idea in the first place.

Re: Glue up suggestions

#22

Ellis Walentine

De-Sta-Cos are your friend

Ellis Walentine

I used to make all kinds of furniture and picture frame jigs, John. One of my favorite go-to technologies was De-Sta-Co clamps mounted on a piece of plywood. They cost more than bolts, but they're a lot slicker, and you can quickly vary the pressure to accomodate oddness in your parts.

Ellis

Re: Glue up suggestions

#23

Leo Cuellar

Re: Glue up suggestions

Leo Cuellar

Hi John.

A couple of questions... Are you making the mirrors the same size? If so, are you using the same bend pattern? Do you you plan to make more than a few?

Perhaps, instead of heat bending you could use cold bending to shape the strips before your glue-up. Make some clamp blocks to the specific curves. Soak your wood strips in water & clamp a couple/few strips in each jig over night & move on to the next project while you wait for the bend to set. Thin strips dry out real quick, so you wouldn't lose too much time there.

I haven't used this technique in 35 years, but my nephews literally wore the wheels off their wooden trucks several times over.

With what I've learned on WC, I might consider boiling the strips as the wetting process, to make them dry faster. I would also cut the strips slightly short for each particular detail so they wouldn't stick out & be a hindrance to clamping.

You always post such interesting conundrums! Good luck