Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

Burl bowl

Posts

Burl bowl

#1

Burl bowl

John Lucas

A friend gave me this burl many years ago. It had a huge defect in the middle that went pretty deep. I had waxed the upper surface and put it up until I could figure out what to do with it. Then it finally hit me. I wanted to turn a bowl and leave the outside completely natural. I figured out how to mount it using hot glued wedges. I think this is Oak burl but not sure.



Re: Burl bowl

#2

Allan W

Re: Burl bowl

Allan W

Nice bowl. Thanks for the mounting idea.

Re: Burl bowl

#3

Steven Antonucci

Like the solution for mounting

Steven Antonucci

I think I'll be able to do something like that with a burl cap I have sitting around.

S

Re: Burl bowl

#4

Re: Burl bowl

Terry Scott

So John the Hot melt wedged glue trick

Yes it works amazingly well Ive held on some Very Large pieces this way.

Leaving as mother nature mad it sure is tactile.

Nice finish that complements the timber well

very nice work as always

Cheers

Re: Burl bowl

#5

Re: Burl bowl

Hugh Widdup

how did you remove the wedges and glue from the bark? i have a couple of these and have been stumped with how to do this.

Re: Burl bowl

#6

Allan W

Hot Glue Mount?

Allan W

I am new to turning and would like to know how you remove the bowl from the wedges when you are done. Do you use a special kind of hot glue?

Thank you

Al

Re: Burl bowl

#7

Re: Burl bowl

Don Thur

John, Nice job; it doesn't look like Oak in my opinion; it has all the characteristics of Yellow Birch burl(as we know it here in Canada). It looks like the bark is flakey and also has a yellow/goldish tinge.

Don Thur

www.knotsburls.com

Re: Burl bowl

#8

Re: Burl bowl

john Veerkamp

looks like white oak burl to me. I've done several dozen similar pieces. Instead of wedges, I usually mount between centers and turn a 2"-3" flat on the bottom and then glue on a waste block. a tenon on the waste block holds the piece for turning the face/bowl.

I really like working with irregular burls like this. Nice job.

Re: Burl bowl

#9

Re: Burl bowl

John Lucas

I just hit them with a hammer. On smooth bowls I use a piece of thin guitar wire on handles. I pull the wire through the glue joint with a sort of sawing motion.

well I should say the first thing I do is try to peel the glue off. Sometimes it comes off some good hard tugging. When that fails I go with the wire. In this case I didn't think the wire would work and actually thought I would damage the bark anyway and have to go to plan B. Howevever the hammer worked quite well and actually left very little glue on the bark. Relieved a lot of stress while I was at it. Nothing like beating on something with a hammer to relieve stress. I think Thor the god of Thunder was actually the Psychologist of the gods.

Re: Burl bowl

#10

Alan-see above


Re: Burl bowl

#11

Dale Jablonski

Re: Burl bowl

Dale Jablonski

Beautiful piece John. Thanks for the tip on using the wedges and hot glue. You are correct, nothing takes the aggression out like beating something with a hammer!

Re: Burl bowl

#12

terry Scott uses a heat gun

Darryl

I've been watching Terry Scott's videos. He uses a heat gun one his winged turnings to soften the glue it seems to come off easily.

Re: Burl bowl

#13

Jim Barbour

Re: Burl bowl

Jim Barbour

If the piece is small enough I pop it in the microwave for 30 seconds or so. The glue softens up and comes right off. Of course for a big piece a hammer may be preferred -- depending on how the day is going ;)

Re: Burl bowl

#14

Brad Vietje

Re: Burl bowl

Brad Vietje

Cool mounting method, John.

Only thing I'd be concerned about is how well the bark adheres to the burl. One could always peel the bark off if it looked like it might tear away.

Nice looking bowl, and sure looks like one of the Oaks from the photos.

Safe spinning,

Brad Vietje

Newbury, VY

Re: Burl bowl

#15

Re: Burl bowl

John Lucas

Brad I worried about that and of course stayed out of the line of fire. However it's being from all directions. The hot glue holding the wedges to the board are more or less holding the bowl from flying sideways. The glue to bark is doing that as well as keeping it from popping out.

nnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmm My dog typed this. She just has to stand on my keyboard for attention.

Re: Burl bowl

#16

Re: terry Scott uses a heat gun yes I do

Terry Scott

Doesnt take much, heat gun on low heat enough to soften the glue

On a burl you can have on full blast as the heat wont hurt the wood

If you want to place a large piece on the lathe with hot melt glue place on all the connection points on the holding mount .By the time you have done them all some of the glue will have hardened.Get out the hot air gun and heat all the glue so it is at a even melt .Them push the work piece into the glue.

When removing scrap off any residue when still melted then with Turps soak the glue left on the work.

If a burl you can place in the freezer and the glue just picks off

Re: Burl bowl

#17

Have been told DNA will take hot glue off

Jim H

Have been told DNA will take hot glue off. I have not had the need to try it as of yet.

Re: Burl bowl

#18

Re: Have been told DNA will take hot glue off

John Lucas

It does. That is what I use when I have to glue to a finished piece. I use the wire garret method to remove the wooden wedges, then some glue will easily peel off. the rest I remove with Alcohol.