Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Can you help an electrical dufus out?

Posts

Can you help an electrical dufus out?

#1

Can you help an electrical dufus out?

Molly Winton


Good heavens, help me. I feel like such a dufus. I want to connect my power cord to my new engine (that will power my new belt sander!!). How do I do it??? Do I use the red connector and sandwich it under the nut? OR do I use the blue connector and slip it onto the prongy-thingy? I assume the green wire is connected to the green screw for grounding...right? And which wire goes on which connector to get it to rotate counterclockwise (is the white wire supposed to be the 'red' one)?

Go ahead, laugh at my incompetence, but then HELP me....please.

Re: Can you help an electrical dufus out?

#2

Re: Can you help an electrical dufus out?

Galen Vetterick

The motor is already set up for counterclockwise rotation with the Red wire on tab 4 and the Black on tab 2 running inside the motor.

Your power cord green does go under the green grounding screw.

The black wire on cord is connected to the tab just to the right of the #4 lettering this is also L1, not sure why I do not see that marking.

The white wire add a female spade connector and put it on the tab just above the L2 marking.

If you ever need clockwise rotation just switch only the motor red and black wires making Red 2 and Black 4

Re: Can you help an electrical dufus out?

#3

Re: Can you help an electrical dufus out?

Bill Turpin in WNC mountains

No way are you a dufus!

Re: Can you help an electrical dufus out?

#4

TA DAAAAA!!

Molly Winton


I received a very helpful phone call from Clifford, and he walked me through it, which was reinforced by your response Galen. Thank you both SO much!

Funny thing, even though the label notes the factory positioned connections should have it running counter-clockwise, it ran clockwise. I switched the two, and now it runs the way I want.

Bill, you are very gracious, but when it comes to electrical stuff, 'dufus' is an apt moniker. I am now one step away from the label though, thanks to Clifford and Galen.

I am now a happy girl, with a new toy that works!

Re: Can you help an electrical dufus out?

#5

I don't call married women 

Re: Can you help an electrical dufus out?

#6

Re: TA DAAAAA!!

Bill Turpin in WNC mountains

Molly, I worked with industrial maintenance technicians for forty years. They asked the same questions as you did. Congratulations , you asked for help!

Re: Can you help an electrical dufus out?

#7

Rob Wallace

Is that the Lee Valley Belt Sander?

Rob Wallace

Hi Molly!

I am glad you have gotten your new toy together OK and have it play nicely with you! (I suppose I'd not hesitate to take advice from Galen - he lives here in Ames and is an active member of our club!) It looks like the "you finish building it" belt sander from Lee Valley - is that correct?

I have looked into getting one of these, given that I have at least half a dozen or more spare motors around here. Looks like a good deal....?!?!

Once you have given it a bit of a workout, could you please post how you like the machine in general? Will you be using it primarily for sharpening, or will it be mostly for use on wood?

"Inquiring minds want to know!"

Thanks,

Rob

Re: Can you help an electrical dufus out?

#8

Rob Wallace

Forgot to add.....

Rob Wallace

.... that the motor does not appear to be a TEFC type, and thus, you should try to fit it up with something (shield, vacuum port, etc.) to reduce dust and particle infiltration into the motor itself while in use. Build up of wood or metal dust, and perhaps worse, abrasive grit particles, can do some serious damage to the motor's innards.

Just something to think about.

(Don't forget to protect your eyes and lungs while using it too!!)

Rob

Re: Can you help an electrical dufus out?

#9

Re: Is that the Lee Valley Belt Sander?

Molly Winton

Hi Rob,

Yes, it's the Lee Valley sander.

I will be primarily using it for sharpening. When I taught up at the Lee Valley store this past year, they had three of them to use in the classroom. Part of my class was making miniature hollowing tools out of allen wrenches, and these sanders were slicker than snot to use. One of the things I liked so much was the ease in changing the sanding belts. In seconds I could go from an aggressive 60 grit, to a polishing 220 (and can go much finer). Right now I intend to use it for all my tools that aren't gouges. I still use my Wolverine for them, and like the consistency I get.

I'll try to remember to let you know how I like it after having it in my shop, but if I forget (dang short-term memory), remind me.

Thanks for the advice on shielding it from dust. I'll see what I can rig up.