Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

In the 25 yrs. I've been turning ......

Posts

In the 25 yrs. I've been turning ......

#1

In the 25 yrs. I've been turning ......

JamieDonaldson

...I had not until now attempted a plate/bowl(?) with a wide rim and undercut inner edge like this. My favorite Hunter tool #5 was the ticket for the undercut without any tearout on the end grain, and saved me a ton of sanding. This turned out so well I might try another some day! 11"W Ambrosia Maple

Re: In the 25 yrs. I've been turning ......

#2

Re: In the 25 yrs. I've been turning ......

Mike Brazeau

Nice work Jamie. I agree the Hunter tools are one of the best additions to our arsenal in recent times.

Re: In the 25 yrs. I've been turning ......

#3

Don Leydens

Re: In the 25 yrs. I've been turning ......

Don Leydens

She's a beauty. Classy with nice gentle curves. I love that Hunter tool as well. Killer wood that has a great finish as well. A beautiful piece, Jamie.

Re: In the 25 yrs. I've been turning ......

#4

Re: In the 25 yrs. I've been turning ......

John Lucas

The Hunter #5 and #4 are my favorite tools for doing and undercut edge or rim. I've been meaning to do a video on that. Need to put it on my list so it will get done. I've tried a lot of tools to do an undercut rim either inside or out. The Hunter is by far the best. I start with a bevel rubbing cut and then rotate it into a scraping cut as I work my way out.

I've been able to do very deep rolled over rims using this technique and nothing makes a better candy dish than a bowl with a slightly undercut inner rim. You can scoop the candy or nuts out better.

I think I can demonstrate that on a stationary bowl that's been cut into a slice so they can see the action of the tool and how it's rotated. I can probably glue up a cutout from the scroll saw to keep from ruining a real bowl.

Re: In the 25 yrs. I've been turning ......

#5

Re: In the 25 yrs. I've been turning ......

Mike Foster

Hard to believe that you've never done one of these Jamie. I guess it's because it's not square, but you could even do a square version of a bowl like this. I have't tried a Hunter for a form like this yet, but may have to give it a go just because I too love that #5. Great stuff!

Mike

Re: In the 25 yrs. I've been turning ......

#6

Leo Cuellar

Worth the wait!   


Re: In the 25 yrs. I've been turning ......

#7

Mike Stafford

Re: In the 25 yrs. I've been turning ......

Mike Stafford

Jamie, a great looking platter/bowl and I love the undercut rim.

When I took Frank Penta's platter class at JCCFS one of the things I wanted to learn how to do was undercut the rim. I was finally able to do it with my Hunter tools.

Later I took a workshop with Nick Cook and asked him how he might do the same cut and to my surprise he showed me how to do it with a 1/4" bowl gouge with a swept back long grind. It worked beautifully and as hard as it is to believe I think the finish was superior to the Hunter tool on the ambrosia maple I was turning.

Just goes to show that there are multiple ways to skin a cat and one should not stop learning new methods.

Re: In the 25 yrs. I've been turning ......

#8

Keith Tompkins

Re: In the 25 yrs. I've been turning ......

Keith Tompkins

Great work Jamie!

Re: In the 25 yrs. I've been turning ......

#9

Nice piece Jamie!

Jorge

I do make very similar shape often and my tool of choice for the undercut is a 1/2" bowl gouge from Doug Thompson.

The hunter tool I use mostly in woods with lots of figure, like curly maple, nice tool.

Re: In the 25 yrs. I've been turning ......

#10

Re: In the 25 yrs. I've been turning ......

Jennifer Indy.USA

It turned out very nice Jamie. BTW, what a nice surprise to see you at SOFA!

Jen :)