Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Opinion Poll: Which is more important?

Posts

Opinion Poll: Which is more important?

#1

Steven Antonucci

Opinion Poll: Which is more important?

steven antonucci

Riding the bevel or a sharp tool?

Steve

Re: Opinion Poll: Which is more important?

#2

Re: Opinion Poll: Which is more important?

Bill Turpin in WNC mouintains

Riding the bevel is a technique. Sharpness is absolutely necessary. It is possible to turn without riding the bevel.

Re: Opinion Poll: Which is more important?

#3

Steven Antonucci

Can't vote for both, Bill

steven antonucci

I agree that both are important, but I am asking which do you think has a more profound effect on the results...

A Sharp tool off bevel vs. a dull tool on bevel...to be clearer.

Steve

Re: Opinion Poll: Which is more important?

#4

Re: Opinion Poll: Which is more important?

Barry L Elder

Yes! :D

Re: Opinion Poll: Which is more important?

#5

Lyle Jamieson

Re: Opinion Poll: Which is more important? *LINK*

Lyle Jamieson

What’s the consequences??

Don’t have bevel support?? There is no direction or control to the depth of the cut. It will likely get a catch. Best case scenario is there will be tool marks and a rough surface behind. With the bevel you are in complete control of the depth and direction of the cut.

Using dull tools also causes problems. But it is on a sliding scale from

* sharp.

* used, but still sharp enough to do some things.

* dull, but usable with force and excessive sanding required.

* dull to the point where it is dangerous to use.

What is the consequence of forcing a dull tool to cut?? Result, hard work, torn out grain, and poor surface behind that needs excessive sanding.

Conclusion: using a tool improperly without bevel support can lead to more severe problems then sanding.

I just posted/loaded 40 YouTube clips. These are not sales oriented but snips from my demonstrations and teaching.

One shows how to line the bevel up prior to every cut.

http://youtu.be/HV9C7O0wUjU I hope this works, I don’t know how to post a link.


Bevel supported cuts

Re: Opinion Poll: Which is more important?

#6

Leo Cuellar

Depends on

Leo Cuellar

the tool, you don't need to ride the bevel with a scraper :D

Re: Opinion Poll: Which is more important?

#7

Re: Opinion Poll: Which is more important?

John Lucas

Kind of ambiguous question. You can turn without rubbing the bevel. The cut won't be as clean and you don't have the control to give a good shape. A sharp tool will help some in this case. so if your comparing a really dull tool rubbing the bevel vs sharp tool not rubbing the bevel then your going to get tearout with either.

Why not just sharpen the tool and rub the bevel. :)

Re: Opinion Poll: Which is more important?

#8

thanks Lyle - helpful YouTube links


Re: Opinion Poll: Which is more important?

#9

Lyle Jamieson

Re: thanks Lyle - helpful YouTube links

Lyle Jamieson

Thanks Henry,

I have had a ton of great comments on the videos. For those unfamiliar with the way YouTube works. I'm still learning. Go to YouTube home page, search for Lyle Jamieson. If you want to subscribe to my channel click on one of my clips (Not Craft Supplies, or others posting about me). You can see the entire listing of topics from my channel.

Re: Opinion Poll: Which is more important?

#10

Denis Putland

Re: Opinion Poll: And the point is ????

Denis Putland

??????? I wonder what uses we can put the results of a poll such as this to use doing. or not doing???

Just curious ????

You do not happen to work for the goverment do you :):):):)

Denis

PS; By the way I rate both as a ten in a score from 1 to 10.

Re: Opinion Poll: Which is more important?

#11

Steven Antonucci

The point is to spur conversation

steven antonucci

and I suppose my question back to you is "why are the both 10 out of 10?"

It's pretty common for people to repeat what other people say, but repeating it doesn't mean that you understand it. People throw around words like bevel and sharp, and having an intimate knowledge of the relationship these things have to a clean surface is not as common as you think.

If you still own 80 grit sandpaper, you don't understand.

Steve

Re: Opinion Poll: Which is more important?

#12

Re: Depends on

Coyne

I just flew (commercial) home with my whole family from Oregon to Florida. I am glad that we did not have an inflight discussion as to which was more important to the success of the flight--the engine or the wings.

Coyne

Re: Opinion Poll: Which is more important?

#13

Re: The point is to spur conversation

Jim Breeden

60 grit - just in case :D

Re: Opinion Poll: Which is more important?

#14

Re: Depends on

Jim Breeden

No wings - no lift. :)

Re: Opinion Poll: Which is more important?

#15

Re: Opinion Poll: Which is more important?

Paul Vechart

I turn bowls all the time without riding the bevel. The David Ellsworth's technique for turning bowls does not have you riding the bevel at all. I can see that riding the bevel on the inside would give a better finish and require less sanding. Of course you have to have a sharp tool.

Re: Opinion Poll: Which is more important?

#16

I did NOT vote for both!

Bill Turpin in WNC mouintains

Turning with dull tools is always bad. Good turning is possible without the use of the bevel (but not always). So Sharpening is more important. Let's spread the poll: DO YOU HONE FOR A BETTER EDGE?

Re: Opinion Poll: Which is more important?

#17

Rubbing the bevel but it has to be sharp

Terry Scott

If it has a bevel I can turn with it '

And Ive used some strange things

2 weeks ago I did a demo were I turned with a claw hammer and a nail

Had to be sharp or I wouldn't have gotten any shavings coming off.

In the old days they never rubbed the bevel everything was done with a file scraping but Id say I can get a finish 20 times better rubbing the bevel.

Oh and I never hone waste of time as I always roll over the edge and make it worse

Re: Opinion Poll: Which is more important?

#18

Re: Opinion Poll: Which is more important?

robo hippy

Well, you can't cut with a dull tool. So pretty important.

After watching Stuart Batty on Thursday evening, it reinforced the idea that 'riding the bevel' is a difficult concept to get into our heads. Mostly, you barely kiss the bevel, not ride or rub, and most of us use WAY TOO MUCH PRESSURE which leads to all sorts of minor cutting errors, and/or deviations from the intended path.

robo hippy

Re: Opinion Poll: Which is more important?

#19

Re: Opinion Poll: Which is more important?

George Guadiane

A while back, I stopped "riding" the bevel and started "resting" the bevel as I turned. "Riding" suggests pressure and could end up crushing the grain. By "resting" I mean like when I wash my feet in the shower... I lean on the wall JUST ENOUGH to keep from falling over. Light pressure as a guide rather than heavy pressure like a crutch

And OF COURSE, with a sharp tool.

Re: Opinion Poll: Which is more important?

#20

Re: Opinion Poll: Which is more important?

Dale Miner

This is an apples or oarnges situation.

I like apple pie better.

You can't cut rubbing the bevel it the edge isn't sharp. In order to make a dull edge cut, it must be lifted ever so slightly off the bevel to make the edge penetrate. Or another way of looking at it, the bevel on a dull tool becomes increasingly extremly small, and the original bevel becomes secondary.

So... If forced to vote for an apple or an oarnge, I will vote for sharp.

Re: Opinion Poll: Which is more important?

#21

Steven Antonucci

My take on the topic

steven antonucci

First and foremost, both are important and critical to getting the best finished surface. Given the choice of turning with dull tools or finding another hobby, I would probably take up knitting.

I am a very average carver, and I belong to a carving club. By carving standards, all turning tools are butter knives. We consider a grinder edge as "sharp", but any average carver would throw away that tool because you wouldn't be able to cut with it at all.

I was at a club meeting with a new carver and she had no practical understanding of wood, sharp, bevels... any of it. I lent her a small, kind of sharp, palm gouge because she wanted to cut a channel in a small pine block. The difference of a few degrees in her presentation changed her cut from being ragged to polished.

I will submit that given the opportunity to present the tool with the bevel in proper contact has a greater effect in final surface quality than the quality of the edge. I am not suggesting that we all stop sharpening, but I have used a lot of tools in demonstrating at craft fairs that are beyond a useful edge, and you can still get a serviceable result if you've got good bevel contact.

Steve

Re: Opinion Poll: Which is more important?

#22

Both but...

Don Orr

...I also agree with you last paragraph Steve. I have changed to describing my approach as "bevel support" instead of riding or rubbing which causes bruising as has been mentioned. And you don't need a long bevel either. A small primary bevel with a relieved secondary bevel seems to work well for me, especially with hollow ground tools. Allowing the wood to cut at it's own pace and not forcing the tool into it makes a big difference. (Even with less-than-optimally-sharp tools)But we all know that already. I actually turn with a crazy-sharp carving tool when I need to cut something off cleanly without pulling fibers out for a nice finish-mostly on spindle-oriented projects.

Another good topic for thoughful discussion!

Re: Opinion Poll: Which is more important?

#23

Steven Antonucci

Do I hone?  You know I do

steven antonucci

but that is a completely different set of topics...

Steve

Re: Opinion Poll: Which is more important?

#24

Re: Opinion Poll: Which is more important?

robo hippy

Well, the interesting thing is you can turn an entire bowl without touching a bevel, and get a good surface. Most of us will shear scrape, both with gouges and scrapers, which is not a bevel rubbing cut. You can cut very deep with scrapers, and I have never had one that would self feed. It only cuts when I push on it, and I can rough as fast as any one I have ever seen. Of course the finish from a roughing cut is rough because it is a roughing cut. You can cut very shallow without rubbing the bevel, and they can be very delicate and controlled cuts. Just depends on how you present the cutting edge to the wood. I am sure some of you have at least heard of Michael Mouse on the AAW site and Woodnet. He is rather opinionated about cutting with a continental style (another form of SRG) gouge with a flute shaped like this ). His finish cut is with a high shear angle, and not rubbing the bevel, more like a shear cut. IT works for him.

robo hippy