Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

More advice for new turners

Posts

More advice for new turners

#1

Steven Antonucci

More advice for new turners

steven antonucci

We have a great thread going on about safety, but I wanted to post some more practical advice that I try to offer in my classes.

1.) Don't buy wood. Odds are that you have a less than 50% chance of getting it off the lathe, and almost 100% chance that it won't be very good, so don't buy wood. You will be a lot less likely to try to "save" a piece that cracked in flight if it was free.

2.) Bears repeating. Start small.

3.) Avoid exotics and burls. Even if you get them for free, they pose different problems that beginners simply cannot overcome until they have some tool skills. Favor local, straight grained woods and do not be afraid to take wood off to get a better form.

4.) While you are learning to turn, buy a chainsaw (if you don't own one). One of the single best things you can do to increase your ability is to gather your own wood. When you do, you stop thinking about all of the cost and the money you are "putting on the floor". Even if it is only a little electric saw, it will pay for itself in a year.

5.) Cut more than you need, burn the stuff that doesn't dry right. My clubs have some "occasional turners", and if we have a "cutting party", I will see guys who only take one or two pieces. When I ask them why, they usually answer "well, I don't turn that much" or "I don't have any way to cut it smaller" (see #4). These are the same guys who likely fit #1, and need as much free as they can carry.

6.) PRACTICE. When I was learning, there were days that I would go out to the lathe, and just turn beads. Or pick up a skew. I used the time to practice tool control, and not make a bowl/thing/whatever. When you stop worrying about having to finish something, you can build skills.

I am sure there are other things. What do you guys have?

Steve

Re: More advice for new turners

#2

Re: More advice for new turners

John Lucas

Steve your last one is the best advice. Just turn. Practice practice practice. If you put a piece of wood on the lathe that you know you are going to throw away it lets you play with different cuts.

That's the big advantage of free wood. It doesn't have to be a piece of pretty wood. Just grab some poplar or maple, cut it into a small chuck and then practice what you want to learn. Rough out the outside and then turn a series of beads. Who cares if they look good, just practice.

If your trying to learn to turn bowls make practice cuts on the inside with a scrap. Try changing the angle of the tool, practice moving the handle to guide the tool, slow down, speed up, see what works for you.

Start small. You can turn a 4" practice bowl in minutes and it's small enough to not be dangerous if something bad happens.

Re: More advice for new turners

#3

Re: More advice for new turners

darrin hill

Learn how to put a finish on... im still working on that..

white diamond, triploi, wipe on poly, carnuba, tung oil, ca, beeswax, waterlox, dyes, etc... too many choices...

when to use which sandpaper, different types of sandpaper, why steel wool, etc....

hard to decide which for which..

Re: More advice for new turners

#4

Re: More advice for new turners

robo hippy

From an old black and white Hollywood movie, where the master swordsman is teaching a newbie (I actually heard a guest on Roy Underhill's program use this for hand saw technique), "Hold it (the tool) like you would a bird. Too tight and you kill it, too loose and it will fly away." One teaching image that will stick in their minds, though some are slow to learn to apply it.

robo hippy

Re: More advice for new turners

#5

snatch this carbide tip from my hand Grasshoper 


Re: More advice for new turners

#6

Re: snatch this carbide tip from my hand Grasshope

Paul Vechart

Great advice everyone. I don't have access to much wood and it always seems to be oak or willow which are not the best to turn so once in awhile I will buy some bowl blanks on the internet from a very good supplier. This is one way to get woods like cherry, ambroisa maple, and mulberry although I will still be on the look out for the free stuff.

Re: More advice for new turners

#7

Dale Jablonski

Re: snatch this carbide tip from my hand Grasshope

Dale Jablonski

Develop a routine and stick with it. Use as a Go/No Go checklist

Am I ready to turn? Am I loosened up? Stretch?

PPE on? (Personal Protective Equipment)

Tools Sharp?

Is the blank secure?

Out of the line of fire?

Now focus

I am sure there are others but the point is develop your routine, stick with it and it will more than likely help keep your safe.

Re: More advice for new turners

#8

Re: More advice for new turners

Bill Jacksonville, NC

Unfortunately, too many new & old woodturners worry more about tools & equipment than wood. Whether woodturners buy or harvest their own wood, need a discussion about moisture content, splitting, sealing, and storing. Without that, conversation folks will end up with lots of kindling. Learning about wood, we turn a lifelong proposition.

When talking chain saws there is a benefit of having both an electric and gas model chain saw. If can only afford one your personal circumstance or prefence make decision easy. Having or borrowing a vehicle capable of hauling all the found wood essential too!

How can you have conversation about chain saws and not one about band saws? I own one and still take a blank from chain saw to lathe, but basic 14” bandsaw nice to have item too!

Re: More advice for new turners

#9

Learn to sharpen well.

Don Orr

And do it with cheaper tools before you destroy the expensive ones.

I think a lot of problems may be caused by forcing dull tools into spinning wood.

Develop good habits early on-bad ones are hard to break later.

Understand wood grain. Know what "downhill" and "with the grain" really mean.

Use a light touch. It's way more important than being able to hog off wood.

Read-Watch-Listen-Learn. Go to every demo you can, read every book you can, watch every video you can, listen to more experienced turners, ask questions.

Re: More advice for new turners

#10

Dale Jablonski

Re: More advice for new turners

Dale Jablonski

Not to be forgotten but maintenance of your tools and shop...is also something that need regular attention. It's not just about turning, it's also about keeping things running smooth and rust/fire prevention.

Re: More advice for new turners

#11

Re: More advice for new turners

Wayne Kuhn

Practice, Practice, Practice. I tell every new woodturner I meet. "we all started in the same place" Every cut I take, I consider a practice cut.

Re: More advice for new turners

#12

Re: Learn to sharpen well.

vamatt

I'm a newbie. Thanks for the advice!

Matt