Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

tips on not getting hit- kind long but important

Posts

tips on not getting hit- kind long but important

#1

tips on not getting hit- kind long but important

John Lucas

We are having some very good discussion on faceshields and along with that some good tips. I thought I would try and throw some out there. I've never been hit in the face with anything other than some bark. I have only had a few pieces come off the lathe or blow up and didn't get hit by those. Maybe I was lucky and these discussions prompted me to buy a face shield and hopefully I will wear it more. Anyway off to the tips to avoid getting hurt.

First of all turn good wood. Keiths tips on cutting around the cracks is excellent. I do that. If necessary I'll simply turn that log into pieces as small as ornament balls. The thing is, you don't have to turn a big bowl out of every log. If it's starting to crack, make it smaller. Better to use a small piece of wood for a box than get hit trying to turn a bowl.

Look very very hard for cracks or defects. After I cut the cracked end off log I will cut another 3/4" slice. Then I try to break it. If it breaks easily there was still a crack I couldn't see. I cut more thin slices until it's solid. Then I cut my bowl blank.

We all love to turn crotch pieces but they often have voids or bark inclusions. Be extremely careful with these, wear protection and stay out of the line of fire.

I started turning with faceplates and drilled extra holes in them on advice from the experts. I used big long screws. That may be why I didn't get hurt early on because my lathe would not go down to slow speeds and my technique sucked. A faceplate with a bunch of good screws will win over a chuck every time. Screws going into endgrain may be the exception but there are ways around that and it's still probably better than a chuck.

When using a chuck, make the tenon fit the jaws. Make a square shoulder on the tenon so the wood sits on top of the jaws as well as inside. This prevents rocking which loosens the jaws and the piece flies. Stop periodically and re-tighten the jaws. The vibrations from turning cause the fibers to crush and the wood gets sloppy in the chuck until it flies off. If you expand the jaws into a mortise, make sure there is plenty of wood outside the jaws. Check to see if the grain runs out, that's an area of possible failure, and make the opening fit the profile of your jaws. Also on expansion or contraction try to make the tenon close to the size of the jaws so they contact the wood as much as possible . On 2" jaws for example make the tenon about 2 1/8 or 2 1/4. If you make the tenon 3" you only touch the wood at 8 small points. These crush the wood more easily and will loosen quicker.

Pay attention. Many injuries happen when applying the tool or pulling the tool back out. You inadvertently touch the wood with the tool while it's not supported on the tool rest and BAM, you know the rest. I did just that during a demo the other day. I was talking instead of paying attention to what I was doing and touched the rim of a platter. I was lucky, nothing bad happened but it sure could have.

Use proper cutting techniques. Learn what causes catches. Most of the time it's getting an unsupported edge into the wood. Lyle Jamieson wrote a great article in American Woodturner a while back on this issue. If your an AAW member you have access to all the previous Journals. Look it up.

Don't extend the tool over the tool rest any further than necessary. It gets hard to control the tool when you have 3 or 4" hanging over the tool rest. Stop and readjust the tool rest.

Watch the speed. Always turn the speed down before you turn the lathe on. This is especially true when first starting up. You may have been turning a spindle at 2400 rpm on your last project. You start a 16" bowl at that speed and you better run for cover.

Stay out of the line of fire. This is impossible to do 100% of the time. By line of fire we mean the direction a piece of bowl might fly if it blows up and comes off the lathe. This is usually perpendicular to the bed of the lathe. I can do that most of the time until I need to really see the form of the bowl. Then I'm forced to lean in a little. That's the dangerous time. Make sure your tools are sharp, you aren't forcing the cut, you have good control of the tool and hopefully you have a face shield on.

OK this is getting long but hopefully I've helped. There are other preventative measures and I'm sure someone will post those.

Re: tips on not getting hit- kind long but important

#2

Re: tips on not getting hit- kind long but importa

phillip medghalchi

John, to add to this ALWAYS wear face shield even when applying glue (to be specific CA)or sanding. I had to replace my lenses not too long ago, since I forgot that I just applied the CA glue with a syringe into a crack and didn't apply accelerator to it to prevent the foaming and the white cloud and it was kind of dry I thought and forgot that the darn thing was still runny inside the crack little deeper than surface and when I started the lathe to do final cut there it goes CA flinging to my eyeglasses. I was lucky and I had glasses on, but it cost me $200 to replace the lenses.

Now, why did I mentioned sanding, because I had pieces very thin that came off the little vase when I was sanding and not shaping and I was lucky that I had my face shield on. Yes, it didn't harm me, but it could have flown into my eyes and well.......

I thought I mention this, since it costs much lesser to replace a $23 UVEX bionic face shield ( I bought it on sale on Amazon) than paying lot lot more at ER for treatment.

Re: tips on not getting hit- kind long but important

#3

Re: tips on not getting hit- kind long but importa

phillip medghalchi

I forgot to add that face shield is not just for when you are turning at the lathe. we all need to wear it when working at the band saw or GRINDER specially (flying metal grinds) those darn things can cause some serious eye injuries. In general any time we are working around any spinning motor for any reasons.

Re: tips on not getting hit- kind long but important

#4

Keith Tompkins

Re: tips on not getting hit- kind long but importa

Keith Tompkins

Hey John, good stuff! One other thought. I almost always use a chuck in the compression mode...remember, if you use it in the expansion mode, the chuck is trying to push the wood apart...turn the wood too thin, pressure too great...WHAM!

Re: tips on not getting hit- kind long but important

#5

Re: tips on not getting hit- kind long but importa

charlie belden

If possible, get the lathe's On/Off switch and speed control, if it's a variable speed, on the tail stock end of the lathe. Why there are still wood lathes with the On/Off switch and speed control on the headstock end - right in the line of fire - is a mystery. A few more feet of wires can't cost THAT much. Seems like a No Brainer, but higher end lathes have this feature, lower end lathes don't seem to.

Re: tips on not getting hit- kind long but important

#6

Re: tips on not getting hit- kind long but importa

phillip medghalchi

Charlie very good point, because it makes me nervous when I am roughing out to reach to the other side of the spinng out of balance piece of wood and turn the switch off. However, I tackled this by buying a foot pedal switch from HF that I bring it out to the right of the timber,on the tail stock side while I am roughing out that way as soon as I feel any thing is wrong I can let my foot off the switch and lathe will turn off. Of course, I noticed that when the blank is about 13" or more and 4"+ high the lathe doesn't stop on the spot and the weight of the blank still makes the head stock to spin, at least not at the original RPM when the motor running, but it is little safer (kind of) but I know that the lathe is going to stop soon.

Re: tips on not getting hit- kind long but important

#7

Re: tips on not getting hit- kind long but importa

Ed Larson

John, thanks for thoughts on preventing wood form coming off the lathe. This certainly is the first line of protection. Face shields are a secondary but necessary line of protection and as seen below they do prevent injuries.

Re: tips on not getting hit- kind long but important

#8

Re: tips on not getting hit- kind long but importa

charlie belden

I turned with a wedge shaped foot switch / dead man's switch, but sawdust and chips would get in it and it'd stop working. Even putting it in a ziplok bag didn't keep things out of the switch. Blowing it out with compressed air sometimes worked - and sometimes didn't. Got tired of having to take it apart to clean it out.

WHY DON'T THE MANUFACTURERS MOVE THE ON/OFF SWITCH & VS CONTROL ON THE RIGHT END OF THE LATHE?

Re: tips on not getting hit- kind long but important

#9

Re: tips on not getting hit- kind long but importa

John Lucas

Charlie I could not agree more. The last time my Powermatic switch quit working I went out and purchased and industrial grade switch. I haven't had time to wire it up because I'm also moving the speed control to the same box. I have all the wiring and switches just haven't take the time to do it yet.

Re: tips on not getting hit- kind long but important

#10

Steven Antonucci

Cheap solution

steven antonucci


I bought the switch on the lower right to solve this problem. It came from Woodcraft, and maybe it was $30? I plug the lathe into it and I can move the switch where I need it. It also creates a two switch situation which is helpful with kids and little fingers in the shop. I get into the habit of turning it off 2x when I am done for the night.

Steve

Re: tips on not getting hit- kind long but important

#11

Re: Cheap solution

Henry (Raleigh, NC)

Steven:

I have the same lathe, with a similar solution. I simply have the lathe plugged into a power bar that has a switch. That power bar is mounted on the lower right and allows me to control lathe power without moving or reaching across the line of fire.

I realize that electrically the switch in the power bar may not be rated for the types of electrical loads that a lathe motor has (I don't know whether it is or not), but if or when the power bar fails I can easily replace it or move to a rated switch as you have.

Henry

Re: tips on not getting hit- kind long but important

#12

Re: tips on not getting hit- kind long but importa

Pete in Holland MI

3 things to add:

1) Listen. A couple turnings that came apart on me developed a crack while turning. During this, the tone of the bowl changed seconds before. The first one, I kept turning and I ended up at the doctors. The second one, I heard the same change in tone, and shut the lathe down before it totally let go.

2) A remote e-stop button on the right side of the machine is very helpfull. Install one on your lathe (found the necessary used parts at work for a cheap price). Recruit the help of an industrial electrician if you need assistance.

3) Do not use a portable on/off switch system like I have seen on some lathes. The second it takes to remember where you put the system during this turning may critical. A stationary location on the right side of the lathe is important. You need to instinctively reach for the stop button, not look, then reach.

Pete

Re: tips on not getting hit- kind long but important

#13

Re: tips on not getting hit- kind long but importa

John Lucas

Good point Pete. Install my magnetic switch in the same place every time if at all possible. That way I know where it is. I actually had thought of attaching a metal strip to my belt so I could in effect wear the darn thing. When I have my powermatic headstock at the end of the lathe there isn't a good place to put the remote which is why I had considered that option. Haven't done it yet because I don't turn that much off the end. I figure if I use the magnet when I walk away and forget that it's on my belt it will simply pop off.

Re: tips on not getting hit- kind long but important

#14

Tape measure holder?

Stuart Johnson

John, Try one of those tape measure holders that clip on your belt?

Re: tips on not getting hit- kind long but important

#15

Steven Antonucci

I disagree on the "same place every time" thought

steven antonucci

My remote switch goes to the place that is most accessible and likely to be needed when I turn.

If I am turning something long, I can turn off the lathe at the headstock with my left hand or my right knee if the switch is there. I have a short bed lathe most days (unless the extension is on it), and I hollow off the end. For these operations, I will actually move the switch either to the end to be knee kicked or to the right or left depending upon the size of the opening and where I am standing during the operation. In the event of a failure, it is probably going to require you to keep both hands on the tool to prevent more wood from being thrown around, and the knee kick allows you to "hold your ground" without having to move to a fixed switch location.

Ideally, all lathes would have big switches on long pendants with strong magnets holding them on. Mine slides if it is dusty, and it is always dusty...

Steve

Re: tips on not getting hit- kind long but important

#16

Re: I disagree on the "same place every time" thou

Guy Brattt

Here's another thought if one has the cash. A teather cord similar to those on boats or /atv's. Attach it to your belt or somewhere out of the way. If shtf you step away and it all shuts off.