Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

avoiding accidents

Posts

avoiding accidents

#1

Keith Tompkins

avoiding accidents

Keith Tompkins

In all the previous "faceshield" threads, I mentioned prevention as the best way to avoid getting hurt; imho, the face shield, which I agree should be worn, is the last resort. Here are scenario's that happen in real life that are completely preventable:

1. The turner is hollowing the inside of a bowl, the toolrest is angled to keep it close to the interior being cut. As he cuts to the center, the gouge slides off the end of the toolrest, the tool drops, contacting the wood. It is carried by the rotation of the blank,arcing around, contacting the tool rest in a dramatic fashion..crushing the turners fingers. I've seen toolrests broken (oneway) during a demo this way! Solution: Cut in the center of the toolrest whenever possible, move the toolrest so there is no chance of running off the end.

2. The turner mounts the new blank between centers, applys face shield, starts the lathe. He never checked the speed. He never knew what hit him until he woke up in the emergency room. Happens all the time. Solution: Bore a hole in the blank that partially buries the drive center. Avoid off-balance pieces if possible. Always check your speed before starting the lathe. Never stand in the line of fire. Use a faceplate for large, awkward pieces.

3. Turner mounts a blank to the lathe. He likes the grain, and the bark inclusion adds interest. As he cuts, a pleasing form is developing...until the blank explodes without warning. Solution: If the turner had studied the blank, he would have discovered the bark inclusion ran through the center of the blank, making it extremely weak. Always examine each piece before mounting on the lathe. Learn to read each piece of wood, and understand how cracks, inclusions, ring shake, etc. affect the stability of the blank. Throw away questionable wood. Like John J. says!

Can you think of a few more!?

3.

Re: avoiding accidents

#2

Don't turn bowls

John Lucas

virtually all the accidents we hear about are bowls exploding. So it would appear if you don't turn bowls then you don't have a problem. Oh sure the occasional hollow vessel or segmented vessel blows up but I don't know of anyone who has been hurt turning an ornament. And of course turning micro goblets is by far the safest.

Re: avoiding accidents

#3

Re: avoiding accidents

Henry (Raleigh NC)

Well Keith as I recall the incident described in the post that started a recent faceshield discussion was the scenario of grabbing a tool and having it come in contact with a spinning workpiece. Sharp end goes down (or thrown up?} and handle is forced up, potentially into a place no one needs it.

Ironically after I read that initial thread - and wondered if that could ever happen to me?!??! - it did just a day later! The new tool I grabbed slipped from my hand! Thankfully the sharp end hit the upward spinning portion of the workpiece and the chisel fell away harmlessly. I had my faceshield on (AND in position!).

So that's another (obvious one since this is where the discussion started?).

Henry

Re: avoiding accidents

#4

Re: avoiding accidents

Eric

Great idea, boring a hole to receive the drive center. I often countersink to receive the live center of my tailstock, but haven't done so for the drive center. I'll give that a try. I often turn pieces that are a bit large for my lathe, and because I have not yet built a newer and better stand, my lathe is a bit wobbly at times, making it susceptible to being rocked by out of balance stock. Which brings me to my point:

If the lathe isn't bolted to a solid, heavy stand, you might consider building one for it. Any wobble in the stand will be exacerbated (word of the day) by an out of balance workpiece. That wobble, of course, will not only ruin your turning, but also reach the point of throwing the stock off the lathe if allowed to continue. The more solid the bench/lathe combination, the easier it is to retain the grip on the piece.

Re: avoiding accidents

#5

you have the answer john!!!!!


Re: avoiding accidents

#6

Brad Vietje

Re: avoiding accidents

Brad Vietje

Good Point, Eric.

It is usually a simple matter to bolt the lathe down, or to add dead weight, Bags of sand and cinder blocks are common, but sand dampens vibration better.

My old Jet 1236 has a pretty light set of legs, so I added a piece of 3/4" plywood, 4 cinder blocks and 2 bags of sand, which must have added at least 200 pounds to the base. My Powermatic 3520B is much heavier to start with, and sits on a concrete pad, but not currently bolted down. I turn a lot of heavy, green wood, so I added a shelf of four 2x6's, topped with three 80# bags of sand at the headstock end, plus 4 cinder blocks at the tailstock end, taking it from a svelte 685 pounds to over 1000 pounds. When I get it installed in my new shop, I'll bolt it down and go to all sand weights.

I'm convinced that more mass is better, and that's one of the reasons I often tell up & coming turners to go find an older lathe with a heavy cast iron base, instead of a lighter but brand-new machine. Old bearings can usually be replaced, but there's no substitute for 800 pounds of cast iron.

Safe spinning,

Brad Vietje

Newbury, VT