Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

New bowl turned with Osprey *LINK*

Posts

New bowl turned with Osprey *LINK*

#1

New bowl turned with Osprey *LINK*

John Lucas

Turned this while working on a video. Interesting tool the Osprey. Works a lot like a bowl gouge but won't take as big of a cut. Although you can use it as a scraper which removes wood fast but not quite as fast a bowl gouge in my hands. However it does leave a good finish when used as a bevel rubbing tool. I started sanding with 220 but had to back down because of 3 small tear out places. 180 by hand got rid of those very quickly.

Finished with Mahoney's walnut oil, 3 coats followed by his wax.

I have also released a new video I did for woodturning fundamentals. This one is on sharpening with a homemade disc sander.


https://www.youtube.com/watch?v=DCS2zUZvIxE

Re: New bowl turned with Osprey *LINK*

#2

Keith Tompkins

Re: New bowl turned with Osprey

Keith Tompkins

Nice one John...I'll have to try that tool!

Re: New bowl turned with Osprey *LINK*

#3

meant to post this video  *LINK*


http://www.youtube.com/watch?v=J_JoR9yLiQc

Re: New bowl turned with Osprey *LINK*

#4

Mike Stafford

Re: meant to post this video

Mike Stafford

You make good videos John. They are always informative and I particularly like the way you demonstrate different techniques with the same tool. Good stuff!

Re: New bowl turned with Osprey *LINK*

#5

Nice video, but maybe....

Dick Coers

not the best tool for pen turning. I know it is not promoted on the video as the best tool for the job. It will be easier for beginners to use the tool, but it will not give them the best lines on the blank with more work. With the small contact area of the Osprey, it will be very difficult to hold a fair curve on the blank. There is no substitute for a long bevel skew that can lay on the blank and take off the high and low spots. Referenced back to hand planning, the Osprey is more like a scrub plane, the skew is like a joiner plane.

Re: New bowl turned with Osprey *LINK*

#6

Re: Nice video, but maybe....

Dale Miner

Agreed, a skew would be my tool of choice.

Re: New bowl turned with Osprey *LINK*

#7

Re: Nice video, but maybe....

John Lucas

I disagree. Respectfully of course because I know you guys know what your doing. I use a very small contact area on my bowl gouges and spindle gouges and don't have any trouble producing a nice curve. It's more about how you control the tool. I use my body and control the tool from the end of the handle so I have very fine control.

I can do the same with the skew or course and I used to feel the same way you guys do. So in reality it might be somewhat easier for a beginner to create fair curve with the skew but they tend to avoid the skew because of the perceived learning curve.

Re: New bowl turned with Osprey *LINK*

#8

Leo Cuellar

Re: meant to post this video

Leo Cuellar

Another great video, John. Thank you for taking the time to make these, they are always informative.

Re: New bowl turned with Osprey *LINK*

#9

Re: Nice video, but maybe....

Dick Coers

Of course we can agree to disagree John, that is what these discussions are all about. I was just going on what I say in the video. As you tapered a curve on the left side of the blank to get to the bushing, it appeared to take extra work to keep constant contact and keep a good curve with that tool. At least that is what I saw. Not an expert of course, I've only been at this for 27 years, and always learning.

Re: New bowl turned with Osprey *LINK*

#10

Re: Nice video, but maybe....

Dale Miner

Hi John.

I wasn't finding fault with the tool. I actually have a Hunter tool, and although not the Osprey, to me the tools with the canelure or chip breaker groove offers more versatility than the straight scraper type. I have one of the flat top scraper types also. I think the carbides have their place, and do use them for some tasks.

I've seen you demo at OVWG and use a skew with proficiency during that demo. With a little practice, no doubt a pen could be turned with a sharpened screwdriver, or a finial with a hatchet (been there, done that). Even though it is possible to use a wide variety or tools to do the same task, some tasks are better performed with certain tools. I think the skew is suited for pens, moreso that the Osprey. Especially if the turner wanted to put small beads or other fine details on the barrel.

It is very likely that most beginners get exposed to woodturning from turning pens. I've seen pen sessions at a local retail outlet where people use everything from 2" roughing gouges through EZ Roughers to beading tools on down to detail gouges. I'm not sure that serious pen turners fall into the catagory of beginner though. Most of the folk I know that have been turning pens for a while use a skew or spindle gouge, unless doing acrylics.

Floating the bevel concept is a tough one for beginners to pick up and especially frustrating when not followed with a skew. Using a Osprey scraper fashion would take the need for that concept out of the picture, but would add a lot of sandpaper time to the equation. Tool control for any tool should be done with the large muscle groups when doing long curves, whether it is a skew or an Osprey. That is another concept that is tough to pick up. The problem for me at least, is that the carbide tools are touted as being easy for beginners to use. While that is true, getting the concept of bevel floating and tool control become less important and often those concepts never do become employed. I think learning to use a spindle gouge for spindle work is the best avenue to learn those concepts. Once the spindle gouge is able to be used with proficiency, learning the skew is worth pursuing.

So, you think I know what I'm doing eh? What do ya know, got at least one person hoodwinked.

We can disagree, no problem. Tell you what, next time we meet, I'll buy you a carbonated beverage of your choice whether it is a diet cola or a barley soda.

Re: New bowl turned with Osprey *LINK*

#11

Mike Stafford

Re: Nice video, but maybe....

Mike Stafford

John and I disagree a little on how to use the Hunter tools. I never use them in scraper mode except for the Hercules and then only when I am initially rounding up the piece. After that riding/gliding on the bevel gives the best cut.

The Osprey really is shaped like a gouge but it has a short flute. The short flute limits the depth of cut on any given cut compared to a gouge. But the sharpness of the tool when used riding/gliding the bevel in a shear cutting mode is amazing to see.

John is a better man than me because I spent two weeks turning bowls inside and out with the Hercules last summer with Mike Hunter. The tool did a fabulous job achieving a fine finish but the excavation was slow compared to a bowl gouge. Removing tearout was much easier with the carbide cutter however because of its ability to remove frog's hair curls.

As I have said many times before I use these tools as problem solvers for particular applications that I run into while turning. I like to use a lot of different tools and I am sure the toolmakers like that.... :b :D

Re: New bowl turned with Osprey *LINK*

#12

Re: Nice video, but maybe....

John Lucas

"The problem for me at least, is that the carbide tools are touted as being easy for beginners to use. While that is true, getting the concept of bevel floating and tool control become less important and often those concepts never do become employed."

Dale I could not agree with you more on this statement. When I talk to professional turners and teachers we have come to one good realization about the carbide tools. If it gets someone interested in woodturning this a good thing. Less frustration is a good thing and scraping with the carbide tools has little if any learning curve.

What I find when I teach is that many people scrape with bowl gouges and spindle gouges. They don't realize it but often are not rubbing the bevel which of course is why they have problems or don't get clean cuts.

I also agree with Mike. I can rough out a bowl many times faster with a bowl gouge than the Hunter tools. Based on Robbo Hippy's style of using scrapers the bowl gouge may not be the fastest but he doesn't use the Hunter tools.

Re: New bowl turned with Osprey *LINK*

#13

Re: meant to post this video

Galen Vetterick

Thanks John for another great video.

Do you get anything for giving the sales pitch to buy an Osprey? :D

Now I'm think'n gee if I buy one for bowls I can even use it to turn pens so it's a good tool to buy. Regardless of if I actually used it for pens!

A question though:

With the Osprey canted carbide cutter and the grind on the supporting steel I wonder if it can be used to cut the inside of a return lip on a bowl. I've tried my home made carbide cutter for this but have had some good catches since I cannot see the transition well from the bowl inside curve to the return top lip curve.

Not sure if I am making this clear.

Re: New bowl turned with Osprey *LINK*

#14

Re: meant to post this video

John Lucas

Galen That's a video I have been wanting to do and keep forgetting about it. The Regular Hunter tools like the #4 or #5 are the best thing I've found for undercutting the lip on a bowl either the inside or outside.

I used to use one of my bent ornament hollowing tools or a vessel hollowing tools. Then one day I figured out a way to do it with the #4 Hunter (which was the only one I had at the time) and the cuts were easy, safe and so much cleaner.

Thanks for reminding me. I will do one shortly. The only problem is I have to destroy the bowl after I turn it to be able to show you how the cutter is positioned. With a thin slice hanging out in space and the lathe off I can show how the cutter is moved to do both inside and outside lips. Oh well it's all for science.

Re: New bowl turned with Osprey *LINK*

#15

My "go to" tool for undercutting...

JamieDonaldson

...a rim is my trusty ol' #5 Hunter, with the 5/8"~3/8" tapered shaft and 3/8" carbide cutter. I can lean on that baby and make it do what I can't accomplish with a bowl gouge, in places that a bowl gouge shouldn't be safely allowed! ;)

Re: New bowl turned with Osprey *LINK*

#16

me too!

GaryG in MD

Was just doing that. Love that tool. ...Gary