Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

Dang Chainsaw brake done broke!

Posts

Dang Chainsaw brake done broke!

#1

Steven Antonucci

Dang Chainsaw brake done broke!

Steven Antonucci

I usually set the brake on the chainsaw when I turn it off to not have to think about it when I restart it. Today, as I have done 100 times before, I did it again.

I couldn't get it to unset? It too me a minute to figure out that the bottom of the break had snapped, and hence, could not unlock the brake. Bad words were said...

Two questions...

1.) What will it cost to fix?

2.) How do I unlock it so I can finish cutting before I get it fixed? Is there any non-obvious means of unsetting the brake if I pull it apart?

Steve

P.S. It was just what I needed in 88 degrees, jeans, and 90% humidity...

Re: Dang Chainsaw brake done broke!

#2

Re: Dang Chainsaw brake done broke!

Jeff Rich

You can probably get the part and fix it if you are handy.

Unfortunately, my old saws do not have a brake...so I am always on the look out for parts. There is a chainsaw forum on an arborist site I visit and they are a wealth of information and would probably give you a step by step.

Re: Dang Chainsaw brake done broke!

#3

Re: Dang Chainsaw brake done broke!

John Lucas

What kind of Saw? I have a husky and the brake mechanism is a spring in a housing. I don't know if I could remove it and still use the saw but think it might be possible. Could even be possible to simply release the tension on the spring which would release the brake.

Re: Dang Chainsaw brake done broke!

#4

Re: Dang Chainsaw brake done broke!

D. Hansen

If it is a "Husky" you can generally take the chain bar housing off and reset the brake spring manually. Be careful though. when you replace the housing it takes some doing and careful discussion with the gods.

Re: Dang Chainsaw brake done broke!

#5

Re:  brake done broke!Dont use Warning !!!!

Terry Scott

Steve instead of suggesting how to fix your saw Id like to say the cost of repair or a new saw Is nothing to the cost to you if you have a kick back and have an accident.

No way id even consider using a saw without the brake.

Even if you have to hire one until your saw is fixed .

You may not of had a kick back for years but as soon as you don't have working Murphs law will kick in.

Sorry I have seen first hand what can happen if any machinery is not up to scratch And one of those was a saw break incident

I could post some pictures as a warning but they are quite graphic.

My 2 cents

Cheers

Re: Dang Chainsaw brake done broke!

#6

Steven Antonucci

Running again

Steven Antonucci

So, with the saw not being operational and neding to cut, I took it apart moreso than I ever have in the past... learned a few things.

The brake is a steel band under a lot of tension. It wraps around a metal flywheel until the brake it tripped. The flywheel is the thing right behind the chain sprocket.

No amount of leverage from any angle would let me reset the brake. I had intended to reset it, and just repeat the process if it was tripped. The brake handle was broken in the "pull back direction"... but I am certain that it would have "kicked forward" to trip if I had gotten a kickback. To no avail, it couldn't be reset... so I took out the steel band that wraps the flywheel. The saw now has no brake until I can get it fixed.

I am aware of the cutting risks if you use a chainsaw improperly. Personally, I think the chainsaw is about the easiest and safest tool a woodturner has in his/her arsenal if used properly. The anti kickback pawls keep the saw in the wood, and you are only making one cut. I would not do field work with it without a brake.

Lastly, if you have never pulled the cover off of your saw (behind the bar), you probably should. I didn't even know it was there, but in trying to reset the brake, it partially opened. I took it off and the entire inside was filled with "mud". It was a combination of decayed sawdust, oil and who knows what else... I cleaned it out with a screw driver and some compressed air. I will now check it every time I tune my saw.

Steve

Re: Dang Chainsaw brake done broke!

#7

Re: Running again

Rodney

Steven, you should clean out that gunk ("mud") on a regular basis. At worst case it can even build up and get under the chain brake and interfere with its proper operation. The shavings when you are ripping with the grain can build up in there and cause trouble too. In addition, it is a good idea to turn the bar over at every sharpening of the chain to even out the wear and, from time to time, clean the air filter to keep the saw running well. While it's true that modern saws have anti-kickback features, probably the best anti-kickback is achieved by the technique of the sawyer, be careful how the nose of the bar approaches the wood. Similar to the way technique is important in turning. I've been using chainsaws for over 40 years, even before the days of sprocket noses and chain brakes, I'm happy to still have all my limbs and no scars.

Re: Dang Chainsaw brake done broke!

#8

Ellis Walentine

And a further warning

Ellis Walentine

I know that a lot of turners use electric chainsaws in the shop to adjust the size and shape of bowl blanks and who-knows-what-else. I have not personally used any of the current crop of electric chainsaws, but back in the early 70s, a good friend of mine hit a nail with one and the kickback sliced his nose in half and put a serious gash across one of his eyebrows, narrowly missing his eye. I was the lucky guy who got to take him to the emergency room.

The moral of the story is, don't underestimate how suddenly or violently a chainsaw can ruin your day.

Ellis

Re: Dang Chainsaw brake done broke!

#9

Steven Antonucci

Noted...

Steven Antonucci

I wonder how many people are injured through no fault of their own when using a chainsaw in the proper manner? Your nail story reminder me of a time when I was cutting up some redwood burl, and there was a piece of granite buried in it. The chain hit it, and there was no kickback at all (because the pawls were engaged). There was a second or two of ticking and a spark or so...followed by bad words being said.

Much like a lathe, the chainsaw operator shouldn't stand in the line of fire. In the event of a kickback, the saw will fly into empty space instead of their face. I am always amazed at some of the things I see with people around running chainsaws. I had a guy I know offer to hold something for me while I cut it. It was a surreal moment- and I actually had to stop the saw to think about it.

I can see people getting hurt felling trees or cutting storm damage...but prepping wood for the lathe should be safe.

Steve

Re: Dang Chainsaw brake done broke!

#10

Pawls?

Mark Mandell - Gone Round In New Jersey

What part are you referring to here, Steve? The only anti-kickback part of a saw (aside from a certain type of chain) that I've seen was the roller-nose cover on some older Homelite saws.

m

Re: Dang Chainsaw brake done broke!

#11

Steven Antonucci

The body of the saw has them

Steven Antonucci

On some larger saws, they are metal spikes that are where the bar enters the body of the saw. On my Stihl, they are ABS plastic nubs. Whenever you are cutting, you should have the pawls against the wood to prevent kickbacks.

Most kickback occur from touching the nose of the saw to the wood. I've seen many people cut with the middle of the bar, and even a few "experienced" guys limbing trees with the nose. If you cut with the back end of the bar and the "pawls" (what I am calling them, anyway) touching what you are cutting, the saw is being pulled into the log and there is no kickback. Ever.

Steve

Re: Dang Chainsaw brake done broke!

#12

Steven Antonucci

Picture of pawls on my Stihl

Steven Antonucci


If you cut on this end with these little plastic nubs touching the wood, there is no kickback. If I have a long cut to make on a hot day, I can wipe my brow without stopping. (Don't do this, merely illustrating a point...)

Steve

Re: Dang Chainsaw brake done broke!

#13

Ah, Difference in Terminology

Mark Mandell - Gone Round In New Jersey

I know those to be "bucking spikes", used to secure the body to the wood in order to have the chain cutting in the most efficient manner. As the cutters try to pull the saw through the wood, the spikes hold it in place. While they don't prevent kickbacks (the kickback force will rotate the saw up and around their contact point), they give the operator increased control and a fulcrum to help control the saw and the kickback.

Re: Dang Chainsaw brake done broke!

#14

PS

Mark Mandell - Gone Round In New Jersey

For safety sake, I'd look into retrofitting that saw with a good steel bucking spike set. The old plastic nubs wear and were most always slip-prone.

Might take a bit of drilling and shaping to fit your saw housing, but the steel unit will give you way more control over your saw, even if you loose an inch of cutting diameter.

Re: Dang Chainsaw brake done broke!

#15

Steven Antonucci

My classes start off with a simple assertion:

Steven Antonucci

You can tell whether or not someone is a safe in the shop with a simple limbs and finger check. If they have them all, they've either got some good habits or just a whole lot of luck. I'd like to think that I am past the point of being lucky and have moved into the "pretty safe/smart in the shop" side of the house...

I have little nicks from being around sharp things all of the time, but I have never touched something sharp that was moving under power.

10 fingers in, 10 fingers out...

Steve

Re: Dang Chainsaw brake done broke!

#16

Steven Antonucci

Between the repair and the mods... a new saw 


Re: Dang Chainsaw brake done broke!

#17

Re: Ah, Difference in Terminology

Rodney

I know those as bucking spikes too, and in bigger saws they generally are truly spikes as you describe. Yep, a fulcrum for "bucking" the end off of a log without having to hold up the whole weight of the saw body. Still, if one lets the nose contact a nearby log or sometimes even a branch through inattention, they can also act as a fulcrum for kickback. The nose guard you mention I have also seen, and mostly they were taken off to avoid the loss of cutting length although they would have helped prevent the danger zone of the nose getting into something that could throw it back. With smaller, less powerful saws one can often "muscle" any kickback away from one's body but attention to how the nose of the saw approaches any contact is the safest way to operate.

Re: Dang Chainsaw brake done broke!

#18

Re: My classes start off with a simple assertion:

Rodney

Well Steven, I imagine that you can also make some assumptions based on how much a person insists on safety equipment. For example, if someone would to refuse to do a demo or class if there wasn't all the necessary safety equipment available so as to set a good example. In addition, making sure anyone watching is also protected sufficiently.

However, I thought this thread was about chainsaw maintenance.

I will comment on your question about how many are injured through no fault of their own. I imagine it is about the same as percentage of turners who are injured through no fault of their own, or the number of flat woodworkers. Using equipment and tools properly and some knowledge of how wood reacts is going to be key to doing a job safely. I'm not sure how we should classify a case where someone didn't yet know enough to realise the danger of what they were doing. Almost all "accidents" would be preventable but even the most knowledgeable workers sometimes take shortcuts or let their concentration wander.

Re: Dang Chainsaw brake done broke!

#19

Second Rule

Mark Mandell - Gone Round In New Jersey

"You do not need to look into the kerf during the cut. Doing so makes your face the first point of contact in a kickback." This is, perhaps the hardest thing to teach people. Standing to the left of the cut-line keeps most of the operator's body out of the path the bar will take if it kicks. Helmets and face shields are not to protect you from falling trees ;)

Re: Dang Chainsaw brake done broke!

#20

Re: Second Rule

Rodney

Agreed, that is a good point, it is similar to not standing in the danger zone of spinning wood.

Although, a brain bucket (helmet) could help protect your head from what the old loggers called a "widow maker" (big broken branch hung up in the top or dead top that falls when the tree moves), some don't think to look up carefully before falling a tree or at the falling line for something that could cause a bit to break off and snap back toward the operator. That's a mistake I made once, a heavy top broke off in tension when it hit another tree during the fall and snapped back, landing where I had been standing to make the back cut. I was lucky, and perhaps smart enough, to have walked away (run actually) to a safe distance while the tree fell but I had not considered the event as a possibility. I suppose if I had been injured it would have been an accident but it would have been a preventable one.

This post seems to have morphed into some chainsaw safety tips and hopefully it can pass on some knowledge to those who don't yet have the experience, help them to think about possibilities. I apologise to Steven for somewhat hijacking his thread on maintenance, he is correct, the routine maintenance he mentions should be done on a regular basis. I also think he should consider turning over the bar from time to time for more even wear.

Re: Dang Chainsaw brake done broke!

#21

Steven Antonucci

No bad dialogue when it comes to safety

Steven Antonucci

FYI- I do flip my bar when I change chains, so I am aware of the practice.

I cut a fair amount of "really dead trees", and in some cases, the saw goes through the first 3-4 inches without hesitation... all rot. It is a different situation when your planned hinge is not out the outer edge of the tree, but somewhere in the middle instead. In these cases, the upper sections are usually also pretty rotten, and I keep an eye on the sky to watch for falling limbs. I never cut something that I have doubt about.

Thanks for jumping in.

Steve

Re: Dang Chainsaw brake done broke!

#22

Steven Antonucci

Maintenance is a safety issue.

Steven Antonucci

A poor running saw is an unsafe saw. If you keep your saw running well, it will do what it needs to do the way it was intended. Using proper technique lowers your probability of being hurt.

All we can do is minimize the risks of having an accident. It requires knowledge and practice. Accidents should be truly accidents-acts of randomness instead of bad practices manifesting itself as evidence. I had no idea that the cover could be removed, but it is now part of my regular maintenance. Any dialogue that opens the best practices to the community is worth having.

Steve