Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

pulley above lathes?

Posts

pulley above lathes?

#1

pulley above lathes?

darrin hill

thinking of putting a small pulley above my lathe for bigger logs. Just severely squished my fingers trying to hold a log in a chuck and push in the tailstock..

any advice or photos? my ceiling is a metal framed building, but i have plywood as ceiling material. Probably wait till it cools off before venturing into my attic, but i think there are some 2x4s that are holding up the plywood...

maybe could mount something into that..

Re: pulley above lathes?

#2

Re: pulley above lathes?

Scott Crumpton

What ever is up there, be sure to spread your load across at least 4 structural members. I would use a 2x8 on edge and put the pulley anchor point at the center.

---Scott.

Re: pulley above lathes?

#3

Re: pulley above lathes?

Bart Leetch

I think a 4x6 would set a lot better on edge then a 2x8. Yes spread the weight over 4 trusses or rafters.

Re: pulley above lathes?

#4

Re: pulley above lathes?

Stuart Johnson

I would go with an engine hoist rather than a pulley above the lathe.

Re: pulley above lathes?

#5

Re: pulley above lathes?

John Lucas

I once saw an A frame set up on rollers that I thought was wonderful. It had a chain hoist. You could simply lift the log, roll it over the lathe and load it up. Storage might be a problem but if you have room that's a great concept.

Re: pulley above lathes?

#6

Joe Bradshaw

Re: pulley above lathes?

Joe Bradshaw

Darrin, I attached a 2x4 above the center line of my lathe and then bolted on a track for a sliding barn door. I attached the wheels to a small electric hoist and I was good to go. It works great for removing the tailstock.

Re: pulley above lathes?

#7

Re: pulley above lathes?

darrin hill

forgot to add that i have about 7 1/2 - 8 feet from floor to ceiling, or about a foot and a half above my head..

and I'm very tight on space... so i would have no space for an a-frame...

Re: pulley above lathes?

#8

Harry Robinette

Re: pulley above lathes?

Harry Robinette

I put an electric hoist above my Vega 2600 for just that purpose. I hear some guys use a deer hoist (rope and pulleys) over their lathes.

Re: pulley above lathes?

#9

Dennis in Southern Oregon

Re: pulley above lathes?

Dennis in Southern Oregon

Surprisingly, if you do the beam deflection calculations you will find that the 2x8 (approx 1.5x7.5 actual) is about 9% stronger than the 4x6 (approx 3.5x5.5 actual). However the latter would give 2 inches more head room if placed below the ceiling. As a practical matter, even a 2x6 laid across joists on 24-inch centers should support much more load than you can lift with a simple pulley. I would put the cross piece on top of the joists and drop a 5/8" or larger all-thread rod through the ceiling to carry the load. A long u-bolt upside down over the cross piece attached to small steel plate bored to take the u-bolt ends and the all-thread can be used to make the connection.

Dennis

Re: pulley above lathes?

#10

Lyle Jamieson

Re: pulley above lathes?

Lyle Jamieson

Joe has the right idea. You need a track or rail to move the hoist up and down the bed. It will never balance from one hook on the ceiling. I use an engine hoist but I have a big shop.

Re: pulley above lathes?

#11

Re: pulley above lathes? *LINK*

ihmserv

darrin,

a track over the center ofthe lathe is probably the best bet.

I have been thinking about putting one over my own lathe.

the style in the link is what I was thinking or something similar.

IAN


http://www.harderwoods.com/hoisttrack.html

Re: pulley above lathes?

#12

Re: pulley above lathes?

darrin hill

see the 10 inch saw blade on the back wall? my ceiling is about that high from the floor..

might have to figure out something smaller scale..

Re: pulley above lathes?

#13

Re: pulley above lathes?

Terry Scott

I have an engine lifter that I not only use to lift my lathe onto the trailer (a 1000 stuby )

But use to lift in bigger blocks

I brought one of these years ago for a engineering business I owned cost me thousands.

The one I have now lifts 1.5 tonne and cost me $250

I can also get on my trailer by myself then use to off load things the other end.Or pick up trunks.

Only thing against it is I have to have a big clean up each time in my workshop when I use it

Having a fixed point above the lathe is not user friendly and has its limitations . A mate has a slide rail that a chain block slides on

but he tends to borrow my lifer as its

more versatile.I can back the trailer right up to my shop pick up a block and take it to the lathe.

When I have a woodturning event on I take in then lifter and eveyone unloads their lathes with it. The wide foot prind means you can pick up my stubby and move it all around the building

Re: pulley above lathes?

#14

Re: pulley above lathes?

Josh Bowman

Darrin,

We debated this over a Saw Mill Creek Forum for Steve Schlumph's new American Beauty lathe and below is the simple cheap solution. It's a dear hoist.