Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

Alcohol resistant finish for chalice.

Posts

Alcohol resistant finish for chalice.

#1

Alcohol resistant finish for chalice.

Jorge

The other day at the market a fellow got transfixed at the sight of a goblet on the table, to the left, the taller.

He is a bishop and wants a chalice and matching plate, same & shape size or close with a finish that will allow to wipe it clean after each use and keep the wood clean, no red wine stains on it.

I have no experience at all with alcohol proof finishes, any suggestions will be much appreciated.


It is not a good picture, but will give you the idea.

3" across 10" high with a captive ring. The wood will be maple. same as this one.

Thank you!

Re: Alcohol resistant finish for chalice.

#2

Re: Alcohol resistant finish for chalice.

Bruce Pratt

Try Behlen Topcoat Laquer (B103-102).

Re: Alcohol resistant finish for chalice.

#3

Re: Alcohol resistant finish for chalice.

Jorge

Thanks Bruce

Re: Alcohol resistant finish for chalice.

#4

JL

Re: Alcohol resistant finish for chalice.

JL

Your biggest problem is staining - they don't use white wine for communion. I've had reasonable luck with 2-part epoxy finishes. I had some left over from a bar top. I figured if it would work for a bar, it would work for a goblet.

It wasn't cheap - but I had it on hand for the bar top.

Re: Alcohol resistant finish for chalice.

#5

Re: Alcohol resistant finish for chalice.

Jorge

Thanks JL,

Epoxy is harder than lacquer, that sounds good to me,

do you remember the brand?

Thanks anew

Re: Alcohol resistant finish for chalice.

#6

Re: Alcohol resistant finish for chalice.

Barry L Elder

Usually available at a nearby boatyard.

Re: Alcohol resistant finish for chalice.

#7

JL

Re: Alcohol resistant finish for chalice.

JL

System Three Mirror Coat - available at Woodcraft. At the time, it was something like $40. I used a lot on the bar top and I had some left over, so I did several goblets.

It was a PITA to apply to the inside. I put some of the liquid in the bottom of the cup portion and gently "spun" it out. I had a box surrounding the goblet on the lathe as well as newspaper shielding the ways.

Re: Alcohol resistant finish for chalice.

#8

Re: Alcohol resistant finish for chalice.

John Lucas

I did what JL did but simply rotated the goblet by hand to cover all areas and then dumped the rest out. Mix it up in a cup and let it start to cook. By that I mean it will start the reaction process and get quite warm. This makes it more viscous. Then I poured it in and swished it around until it cover all the area. Then poured it out.

Unfortunately it was a gift for a friend of a friend and I've never seen it again. Don't know how it held up. I've used the System 3 mirror coat on other projects for various reasons and it's always held up well. Just don't know about the wine staining but it basically plastic when it's cured. It must be more flexible than other epoxies because I've never had a problem with it cracking on my mirror projects and they are 5 1/" wide where a goblet is only 3" or so.

Re: Alcohol resistant finish for chalice.

#9

Staining

Bill Howatt

What about staining (or dyeing) the interior of the chalice with a dark color so red wine stains aren't obvious?

Bill

Re: Alcohol resistant finish for chalice.

#10

Re: Alcohol resistant finish for chalice.

Jorge

Thanks JL,

What I did in that goblet was first apply some thin CA to the end grain in the bottom and then some medium and sanded smooth when it set, then a coat of sanding sealer, let it dry and sand and then several coats of lacquer from a spray can spinning it at the lowest my lathe goes, 48rpm. after each spray. Without the CA first, the end grain in the bottom always did look bad.

Re: Alcohol resistant finish for chalice.

#11

Re: Alcohol resistant finish for chalice.

Jorge

Thanks John,

Good tip.

I will have to experiment in another piece before attempting the final one.

I went to a bar and the bar top has a very shiny top, asking the bar tender he said Kleer Kot or something close to that. He mentioned to be really expensive.

It looked good in the bar top but it is very thick, it must be at least 1/8" that would not look good in a goblet.

Re: Alcohol resistant finish for chalice.

#12

Good idea Bill

Jorge

I'll bounce it with the fellow.

Thank you.

Re: Alcohol resistant finish for chalice.

#13

JL

Re: Alcohol resistant finish for chalice.

JL

When I "spun" mine out, it was less that 1/16" - probably on the order of 1/32". You can make the coating as thick as you want. If it is too thick, just sand some off. When I did the bar top, I wet sanded it to 1500 grit when I was feathering the edge.

Re: Alcohol resistant finish for chalice.

#14

Re: Alcohol resistant finish for chalice.

Ray - Middletown, in

Hobby Lobby has a product by Alumilite that is a clear two part epoxy that is apparently similar to other similar products. Cost was about $20 for a quart of it.

Ray

Re: Alcohol resistant finish for chalice.

#15

Re: Alcohol resistant finish for chalice. *LINK*

William Duffield

Clear Coat is also a System 3 epoxy product, and is also available at Woodcraft.


Clear Coat

Re: Alcohol resistant finish for chalice.

#16

Thank you Ray!.

Jorge

That is very reasonable price.

Re: Alcohol resistant finish for chalice.

#17

Re: Thanks William.

Jorge

Much appreciated

Re: Alcohol resistant finish for chalice.

#18

Re: Alcohol resistant finish for chalice.

Barbara Dill

I've used CA glue for years to seal the grain of all the various woods I've used to make goblets, cups and bowls. I use the thin CA.

Re: Alcohol resistant finish for chalice.

#19

Thanks Barbara