Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

Gun Lamp Progress

Posts

Gun Lamp Progress

#1

Gun Lamp Progress

John Lucas

Well it's slowly getting there. I'm working on the locking ring and locking mechanism for the top. I decided it needed little decoration so I added a split ring. What I did was glue up a ring. Then flattened it and hot glued it to a waste block. Turn the inside round. Then I sawed it in half with my scroll saw.

Turned a groove for the ring and then fit it in and clamped it in place.

This ring will fit over the door and keep it locked in place. There will be 2 brass pins and this ring will fit over those and then turn the ring to lock it in place. To keep this ring from rotating there is a locking lever that will fit into a slot so it will all be locked together. I should finish these as soon as the glue dries. Then it's on to finishing and figuring how to mount the rifles.






Re: Gun Lamp Progress

#2

Mike Stafford

Re: Gun Lamp Progress

Mike Stafford

Very ingenious, John. This is quite the project and you are doing a fine job.

Re: Gun Lamp Progress

#3

Don Leydens

Re: Gun Lamp Progress

Don Leydens

Nice seeing the progress of this piece, John. Thanks for sharing, it is sure coming along nicely!

Re: Gun Lamp Progress

#4

Re: Gun Lamp Progress

Don Orr

This is very interesting. What a great project. Ingenious solutions.

Must be a wild sight turning with all those clamps in place. :D ;) :O

Re: Gun Lamp Progress

#5

All parts finished.

John Lucas

OK well not all the parts. I'm down to figuring how to support the guns. I did make some custom metal pins for the bottom of the door this morning. I took 5/16 bolts and turned the ends down to 1/4". Then tapped the holes in the base and screwed them in. The door will sit on these and lock in place. Then the top locking ring will hold the top in place.

I did finish the top locking ring and got the grooves cut out to make it work. Also cut the locking slot for the key lock mechanism. Funny story but typical of me. I had cut the two slots for the brass pins that will lock the rotating ring in place. I was cutting the horizontal slots and didn't really have the right tool to do it but I was getting there. I simply could not make the thing rotate so I would cut the slots a little deeper. Didn't have a good way to measure this or the right tool to do it (so I thought). Anyway after many tries I finally notices that one of the slots was going the wrong direction. No wonder it wouldn't rotate. So now one of the slots is T shaped instead of L shaped. I'll leave it like that so My son will know I'm not perfect. He's heard me cuss over stupid things like this before.

Then it was on to hand sanding this entire thing to 400 grit. Man my arms are tired. I had previously sprayed the inside with gray stoneflek paint. I applied the first coat of finish. While it's drying I'll figure out how I want to mount the guns and then go a bike ride and think on it some more just in case any ingenius solutions come to mind.

I have to check all my lamp parts and see if I have everything I need. I may need to buy some more wire and possibly a different size harp but should have everything else.


Re: Gun Lamp Progress

#6

Re: All parts finished.

Galen Vetterick

You've got a lot done John. Who would guess it will hide guns, except for a few thousand WoodCentral friends. :D

Is that a wood covered socket and center pipe to run wiring laying at the back of the bench?

Had you thought about cutting recesses in the base for the stock butts to help postion the rifles and cant them in?

Is the base cross bored or a channel cut for the cord if it sets on a hardwood floor?

It does look a little tight to try and do the lazy susan especially if just for two long guns.

I'm beginning to see the light to your project!

Great project!

Re: Gun Lamp Progress

#7

Re: All parts finished.

John Lucas

That thing in the back is my version of the EZ vacuum adaptor. I'm doing a vacuum chuck demo on the club lathe and had to build an adaptor for it.

I'm going to add 3 or 4 real flat feet to the bottom to let the cord go where it will.

I am going to build a cradle for the butt of the guns. I thought about the lazy suzan but the scoped rifles will be too deep and will extend over center so I guess I'm stuck with 3 or 4 guns. I'll know later tonight. I have to finish the other adaptor for a shop vac for the demo before I can play with the lamp some more.

Re: Gun Lamp Progress

#8

Re: All parts finished.

Stuart Johnson

John, when you are completely finished you might want to try and combine your posts or write an article covering the project.

I would be a bit concerned about the the lock on top. If the purpose is to have the guns in a locked cabinet it is fine but I think it might call attention if there is a break in especially if they turn on the light. I have no idea how to conceal it and still have it accessible.