Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Turners equivelent to ice cream headache

Posts

Turners equivelent to ice cream headache

#1

Turners equivelent to ice cream headache

John Lucas

You take a big bite out of an icecream cone and you know up front your going to pay for it but you do it anyway. Then WHAM, that headache hits you.

Well to a turner it's sanding large pieces with fine sandpaper under power. You know at some point your going to burn your fingers but you do it anyway. Your going along nicely thinking man I'm good, and then WHAM it burns a red spot on your finger faster than you can say Ouch (or something like that)

Re: Turners equivelent to ice cream headache

#2

Re: Turners equivelent to ice cream headache

Galen Vetterick

I just don't understand why the signal from your finger has to travel to your brain and then send a signal to your mouth to generate an auditory report BEFORE your hand is given the signal to pull your finger away from the surface. :(

Re: Turners equivelent to ice cream headache

#3

Mike Stafford

Re: Turners equivelent to ice cream headache

Mike Stafford

Mr. Lucas, I learned a long time ago to prevent this particular condition by backing my sandpaper with pieces or strips of white 3M pads. Not only did I no longer burn my fingers I also did not tire my fingers as quickly.

It does hurt though doesn't it..... :b

Re: Turners equivelent to ice cream headache

#4

Re: Turners equivelent to ice cream headache

John Lucas

Mike I've learned that you can fold the paper a certain way, you can back it with Duct Tape, you can wear gloves, etc. Somehow I just never do and usually get away with it. Well 95% of the time anyway. It's that other 5 that gets me. Usually 600 grit or higher and often within the first second you hit the wood. :)

Re: Turners equivelent to ice cream headache

#5

Harry Robinette

Re: Turners equivelent to ice cream headache

Harry Robinette

I believe we've all done it and yes it's fast and hot. I keep cut-up pieces of Styrofoam coffee cups to back my hand sanding, no more burns.

Re: Turners equivelent to ice cream headache

#6

Re: Turners equivelent to ice cream headache

robo hippy

Well, I have blistered my fingers with a card scraper a number of times, but don't think I have done it with hand sanding. I will admit that 99% of my sanding is with a power sander though. One advantage to plain and simple.

robo hippy

Re: Turners equivelent to ice cream headache

#7

Lyle Jamieson

A different sanding method

Lyle Jamieson

I have a different take on this. I have found that I need to slow down...and use sharp sandpaper. Dull sand paper and fast speed will heat up. I dont want to heat up, period. If it is hot enough to burn your fingers what is it doing to the wood?? It is damaging and burning and burnishing the wood and likely starting cracking and heat checks. Wonder why you get a blotchy clouded area and the torn out grain still evident after sanding?? Dull sandpaper!!

So I need to slow the wood down as slow as possible 50-100 RPM or slower for larger diameter pieces. I do not want to use gloves or padding. I need, want the "heat sensor" of my bare fingers, they are an indicator that my sandpaper is dull and the need to move on to sharp paper. I want to feel the heat, but not hot.

When using power sanding disks I only use them for coarser grits. Think of a 400 or 600 grit disk spinning at 1800 RPM of a drill. As soon as it touches the wood, immediately it is dull and from the first second on you are damaging the wood with hot dull sandpaper. Wonder why you melt the velcro?? Dull sandpaper again!! Wonder why you burn your fingers taking the old sanding disk off the disk?? Dull sand paper going way too fast. Again, if you get that much heat, what's it doing to the wood surface, not a pretty picture. I use power sanding for 150, 180, 220 only. Then I switch to hand held 320, 400, 600, with the lathe running very slow or if there are natural egges or voids I sand off the lathe by hand.

More work?? Yes, but the results are worth it if you want to take your work to the next level. Use more sandpaper. Not really!! I only sand once. I sand with the coarsest grit I need to get and tool marks off or correct any torn out grain. After the first sanding is done from then out Im not really sanding but just going through the grits taking the sandpaper scratches from the previous grits. With sharp sandpaper and slow speeds it is quick and easy to go through the grits. I always stop at each grit for close observation. Did I find a flaw from the previous grit?? Go back a couple grits coarser and get it early in the sanding sequence.

Re: Turners equivelent to ice cream headache

#8

Re: A different sanding method

John Lucas

Lyle is right of course but here's the problems I run into. When sanding platters for example, the middle is running really really slow if you turn the speed down to sand the outside rim. Now I like to power sand these and if I do that then it isn't a problem.

However some pieces have details that simply have to be hand sanded and I don't turn the speed of the lathe up and down when changing from middle to outer edge when sanding these details. Generally light pressure is all that's needed because like Lyle said I take care of all the problem areas with the first 2 grits. It's just that when you get to 600 grit all it takes is teensie tiny hair more pressure than you were using for the middle and it will burn you.

I don't have that problem often but we all do it every now and then and even though we know better it still happens. Darn Where's that ice cream I need some more torture.

Going to have some bloodwork done today so can't eat until 3:30. I'm going to die, Where's my donut. I'm putting vinegar on the paper joint this morning to clean it up and it will smell like a salad which will make me even hungrier. Don't know why I'm doing this, there's nothing wrong with me. she's probably going to write down he looks like a greek god but my friends all think when your only 1 month away from 63 you should be visiting a doctor and getting physicals. Oh well it can't hurt, but I could eat a horse right now and still have 8 hours to go.

Re: Turners equivelent to ice cream headache

#9

Lyle Jamieson

Re: A different sanding method

Lyle Jamieson

You are absolutely right John. Its not the RPM but the speed the wood is moving. I do change lathe speeds as I sand from the rim in, I speed up SLIGHTLY and from the middle out, I reduce the speed. Once you get used to changing speeds often through the turning and sanding process its second nature. Your focus is on the speed of the wood not speed of the lathe.

Have I ever burned my fingers?? Yes, but not often. When I do it, I hit myself in the forehead with the palm of my hand and say "STUPID" out loud, or something unprintable. Not cause my finger hurt but I know better and I did not want to have to go back and repair the burnished wood. That's a big waste of time and energy.

Re: Turners equivelent to ice cream headache

#10

Re: A different sanding method

Don in Central Illinois

I, too, have the body of a god, unfortunately, it's Budda.

Re: Turners equivelent to ice cream headache

#11

Harry Robinette

Re: A different sanding method

Harry Robinette

Lyle

don't know if you have seen or heard about Bill Neddow he sands with a angle grinder at 4000 rpm and IT WORKS.Go to Bill Neddow woodturner Canada.

Re: Turners equivelent to ice cream headache

#12

Lyle Jamieson

Re: A different sanding method

Lyle Jamieson

Im not going to convince you and you are not going to change my method. Try it side-by-side. I have found the easiest way I know to sand and get the surface I want left behind on the wood.

Re: Turners equivelent to ice cream headache

#13

Bill Blasic

Re: A different sanding method

Bill Blasic

When it comes to sanding Bill Neddow is the person I would choose to teach me about it. his sanding demo is as good as it gets.

Bill