Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Gun lamp progress

Posts

Gun lamp progress

#1

Gun lamp progress

John Lucas

I had to take a break. Roughing this thing out is kind of tiring. As I noted before it's about 1/4" out of round. Turning it faster would make it easier but I've never turned a segmented item this large (46" and 32lbs) so I'm keeping the speed down. I'm more nervous about the hot glued insert inside that I mounted the faceplate too than I am about the lamp coming apart.

I've been playing back and forth with a large Crown roughing gouge and the Hunter Hercules. The roughing gouge leaves a smoother finish but is a little wearing on the hands. The Hercules with a big weighted handle is much more relaxing but I have to take smaller bites and it doesn't leave as good a finish. Probably because the grain in the wood is sometimes running in stubborn directions. With the roughing gouge I'm holding it at an angle that gives a slicing cut.

Because of some knots and swirly grain I'm getting the best final cuts with a 5/8" bowl gouge with swept back grind and doing a pull cut. The wings on this are narrow so they care quite sharp and cut very cleanly. I'm checking for high spots with a ruler and trimming them down as I go. I'll probably use the John Jordan shear scraper to do the final truing up.



The base and the rings are done except for final sanding. I'll be attaching the lamp to the base with screws in slotted openings in the base. I'll drill those later when I fit the thing together.

Re: Gun lamp progress

#2

Re: Gun lamp progress

Tony - Memphis

Looking good! Thanks for the updates. I've enjoyed watching. I've thought about doing something like this on a much much smaller scale. My wife is an artist and I thought about making her some brush holders using something along these lines. I'm not much of a turner though. Good luck with the rest of this project.

Tony

Re: Gun lamp progress

#3

Mike Stafford

Re: Gun lamp progress

Mike Stafford

Looks great John. I have never turned an assembly that large either so your caution is probably the correct thing to do.

You can get a smoother finish with the Hercules by angling/tilting it just as you would any other cutting tool. The limitation of course is the relatively small bite of the carbide cutter.

Have you tried a wide spindle gouge? I bought a 1 3/4" wide spindle gouge that is great for large spindle work and your project certainly qualifies as spindle work. Perhaps the sharper bevel might solve some of your problems.

Re: Gun lamp progress

#4

Re: Gun lamp progress

John Lucas

Mike I tried my Hunter Hercules and a #5 Hunter tool in bevel rubbing mode. Cuts clean but is really hard to get a perfectly straight cut. Using one of the wings of my Henry taylor spindle roughing gouge worked to a point but was also hard to control.

I finally went to my big gun. It's a 3" spindle gouge. Don't remember the brand. Since I was running this thing quite slow it took a long time and lots of patience to clean up this whole cylinder. It's ever so slightly convex over the whole length but no one will know but me.

Between the big spindle gouge and my John Jordan shear scraper I was able to clean it up. I still have a little clean up in a couple of areas and will probably have to use a cabinet scraper to get the tearout in a couple of spots. It will have to wait until tomorrow. I'm tired. Well not that tired. I am going for a long bicycle ride. I promised myself I'd do a down the mountain ride today which of course means I have to come back up the mountain. The ride I have planned I think it about 34 miles. Hope I've got the legs to do that.

Re: Gun lamp progress

#5

Mike Stafford

Re: Gun lamp progress

Mike Stafford

Well, a 3" gouge should do the job. I think I have gouge envy.......

Re: Gun lamp progress

#6

DANG John, where did you find.........

JamieDonaldson

...that beast??? Is it a forged continental gouge like was popular back in the old days?

Re: Gun lamp progress

#7

Re: DANG John, where did you find.........

Josh Bowman

John, that is really looking great. Can't wait to see the finished product. Your son will be pleased.

Re: Gun lamp progress

#8

Re: DANG John, where did you find.........

John Lucas

Jamie Always wanted something like this ever since I saw Rude use one. I was in Atlanta and found one at a tool sale for $10 so naturally I jumped on it. I think I need to grind it at a slightly sharper angle.

Re: Gun lamp progress

#9

Progress indeed!

Don Orr

This is really coming together nicely John. Thanks for letting us follow along. Very impressive project. Looking forward to the finished piece.

Hope you had a good ride.