Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

On the subject of shop accidents:

Posts

On the subject of shop accidents:

#1

Steven Antonucci

On the subject of shop accidents:

Steven Antonucci

From time to time, it probably makes sense to recant our own personal tales of woe. There are plenty of obvious dangers standing at the lathe, such as being struck by the workpiece, but I thought I'd share three of my personal experiences.

First, I have a Nova 3000, and I have a handwheel on the lathe that is great for many things. Over time, I have used it as a braking mechanism when I am in a hurry. I have learned two situations where patience is a virtue. First, when your lathe is spinning at 3000 rpm, it will create enough friction through a glove to burn you. The blister serves as a reminder for a couple of days about your indescretion.

Secondly, when the lathe is in a lower speed, it is usually because there is a large spinning mass mounted. There is something called inertia, and it means that the large spinning mass will spin until it is darn well ready to stop. When the lower speeds are used, the handwheel is aproximately a finger thickness from the motor body. I say approximately, meaning slightly smaller. I know this because I have had my fingers pulled through this slightly smaller opening. It is the mechanical equivalent of hitting your thumb with a hammer. The effect is about the same duration as the blister.

Also, note that a Oneway lathe will stop when it is ready to stop, and the handwheel will gladly dislocate something for you if you try to disprove that fact.

Next, my personal experiences with CA glue. I shudder every time I see someone flooding a crack with CA glue, as it may not cure all of the way through. I did this, and then cut through the cured top while turning. The spinning piece threw uncured CA into my eye (yes, I should have had eye protection, but admit it, we all skip it here and there). It is safe to say that the chemical burn in my eye cause more pain that I can describe, and I would sooner use the handwheel every day as a brake in low gear before taking a micro dot of CA glue in the eye.

Lastly, I have been cut by attempting to catch a falling skew. It might seem obvious, but resharpening takes about as long as it does to stop the bleeding, and without the mess.

Let's hear about your not so obvious shop warnings.

Steve

Re: On the subject of shop accidents:

#2

Re: On the subject of shop accidents:

Don Orr

I guess I've been lucky so far. I've been cut by a sharp edge on a spinning piece but not badly. I've been cut when reaching for a tool in my rack-(yes they are point-up.) Again, not badly. I've had CA glue slung at me by cutting through the cured surface, but I wear prescription glasses which protected me. I've had pieces fly off but have never been hit-yet. I understand that my lathe has a slow down time to stop (electronic braking) and don't use the hand wheel to try and override it-can't be done anyway without burning your hand. Worst chainsaw accident was when it wasn't even running-brushed the back of my hand against the chain.

I do try to be careful and safe as much as possible. If anything doesn't seem right I force myself to stop and think. I'm in my shop alone and my wife is mostly oblivious and preoccupied in her own world. I would hope that if I don't show up sooner or later she might come and check on me. I did manage to train her to not startle me by walking in behind me and talking to me. She stops at the door and waits for me to take my tool off the wood and then announces herself.

Br careful out there.

Re: On the subject of shop accidents:

#3

Re: On the subject of shop accidents:

Bill Howatt

I've been pretty lucky. A couple of flying bowls when I started turning missed me completely. My worst experience was having too long a spindle being held in a chuck without tailstock support. There was a Beal wheel at the unsupported end and it obviously pulled out of the chuck, hit the ceiling and came down hitting my head. Didn't do any damage to my head IIRC. Hmmm, maybe the IIRC is a clue that it might have! :)

A fellow on a Cdn WW site posted a comment that I think is worth remembering, something like:

If you do an unsafe action 5000 times without incident, it is still an unsafe action.

Bill

Re: On the subject of shop accidents:

#4

Re: On the subject of shop accidents:

Adam Baum

I haven't had any lathe accidents, yet, but I do have a nicely jointed index finger. About 9 yrs ago, a friend walked into my shop and startled me while I was jointing a board. I wasn't any push sticks/hold downs and my hand slipped off the back of the board. Needless to say,I got an ouchie. To this day, I can still see the blood spray in slow motion. It's like watching something get hit with a propeller or run through a wood chipper in slow-mo.

Adam

Re: On the subject of shop accidents:

#5

Re: On the subject of shop accidents:

Carole Valentine

All of my friends know not to enter my shop until I have stopped doing whatever I am doing if it involves power tools. Of course I have a window in the front door so they can see. The UPS people are another story. Usually if I am expecting a delivery, I leave my dog on the front porch and she will warn me if anyone is approaching.

I was taught by my original woodworking mentor to stop and listen for a few seconds at a shop door for any sound of machinery, if there is none then knock and wait for for a "Come in"

The only time I have had a mishap was in my old shop. I was using the grinder and spotted a snake on the floor out of the corner of my eye...I was sharpening a SRG and the edge caught when I moved my hands from the startle reflex upon seeing the snake. My new shop is snake-proof. :)

Re: On the subject of shop accidents:

#6

Mike Stafford

Do not.....

Mike Stafford

try to prevent the pointy sharp end of any tool from hitting the floor with your foot while wearing a pair of Crocs.

sharpen a tool on the grinder without first checking to see if the Wolverine slide arm is locked in place.

turn in reverse with a chuck that cannot be locked on the spindle.

turn with the chuck jaws extending beyond the chuck body any appreciable distance.

try to slow down the work piece by applying pressure with your hand to the spinning chuck. (I know Jimmy Clewes does it in his videos but I don't do it any more.)

use steel wool to smooth out a finish on a spinning piece unless you are absolutely sure that there are no round areas that can catch the steel fibers and pull you into the spinning piece of wood.

try to cut on the wrong side of the workpiece. I actually caught myself one day trying to cut on the upswinging side of the inside of a bowl and could not figure out why the bowl gouge was not cutting. DOH!

forget to remove the chuck wrench before turning on the lathe.

Re: On the subject of shop accidents:

#7

Re: Do not..... Um

Mark Mandell - Gone Round In New Jersey

That's quite a list, Mike.

You been putting in quality time learning from experience?

[Glad you're OK :D ]

Re: On the subject of shop accidents:

#8

Steven Antonucci

Add this one:

Steven Antonucci

Do not attempt to show you kids how flammable a wax coated rag is in the middle of your driveway (it's really flammable!)

I do the chuck thing, but I always make my tenons the right way, so the jaws never protrude. I have experience the corner of the jaw removing a small chunk of my palm, so I started making the tenons right and solved that problem.

S

Re: On the subject of shop accidents:

#9

Steven Antonucci

Impossible with 4 kids

Steven Antonucci

If you remember Seinfeld and how Kramer used to bust into Jerry's apartment, you know what it is like to have young kids in the shop.

Here are the rules I set early on:

If you don't know what it is, don't touch it.

No running in the shop. (it's amazing how the corner of everything is perfectly aligned with the forehead of a toddler...)

No in or out if there is anything running. Stay put until I turn it off.

And the best one: if I have let you use it in the past, you can use it without asking me. ("Daddy, can I drive the screws in your workbench?" they've been in and out so many times, you can drive them by hand...)

So, not only have I never been seriously hurt, but I have 4 kids who are all in and out of the shop with me all day long, and never a mark on them...

Keep them coming.

Steve

Re: On the subject of shop accidents:

#10

Simply Stated

Tom in Alaska

Simply stated when working on a Lathe: Stupid Happens Quick

I know because I have done many a stupid thing, and have scars, but then again I have all my fingers and both eyes. small wonders ...

Let me add to the list: Use a glove on your left hand as chips from dry wood are hot and if the wood you are working on splinters, chances are it will enter your left hand between your little finger and wrist. I use fingerless gloves with "renewable" duct tape on the wear areas :-) .

Re: On the subject of shop accidents:

#11

Dick Hines

Re: Simply Stated

Dick Hines

I am not even going to list the things that accounted for blood loss in my shop. I have learned in my "old age" to slow down and think before I do anything.

I call it the rail road crossing method . Stop, Look and Listen.

Re: On the subject of shop accidents:

#12

Mike Stafford

Re: Do not..... Um

Mike Stafford

Unfortunately I am an honor graduate of the school of hard knocks...... :\

Re: On the subject of shop accidents:

#13

Re: On the subject of shop accidents:

Ray - Middletown, in

When sanding a winged object, don't reach out to feel how smooth it might be until you turn the lathe off and it comes to a stop.

Ray

Re: On the subject of shop accidents:

#14

Jesper, Denmark

Re: Very interesting commonality....

Jesper, Denmark

Have you noticed that all of these posts relate to the most important safety aspect in your shop?

Use what you have between your ears.

No amount of safety equipment will prevent an acident if you do not use your head.

Re: On the subject of shop accidents:

#15

Re: Shop Accidents

Karen F.

I have to remind myself when I start thinking should I really do this....it's probably a better idea not to do it. I had a piece of maple burl that I was cutting on the band-saw and it was an awkward angle. I thought I probably shouldn't try this but it's "just one more cut" and bang it kicked back and smashed my little finger. I was very lucky it didn't cut it off.

Another time, I was using my Wolverine System to sharpen a gouge, while I held onto the knob on top. The gouge slipped off the edge of the wheel and the same pinky finger went right onto the stone. Again I was lucky it didn't take my fingernail off. Now I have a great scar and a fingernail that grows a little crooked.

The grinder is another machine that is taken for granted. We had a class in my shop and I kept having people leave my grinder running while there were people working around it. I would turn it off whenever I saw it but my friend literary had her shirt ripped in half by the grinder when she walked by it that day when someone left it running and she didn't hear or see it. It could have easily sliced her hand, side or anything else it touched.

I'm extremely careful around the lathe, band-saw and the grinder. I like having all my digits.

Re: On the subject of shop accidents:

#16

Re: Shop Accidents

Barry L Elder

I purchased a Jet 1236 in 2003. In 2004 we had two hurricanes back to back and I spent 15 months salvaging wood. Afterward, I was practicing turning for 6 to 8 hours a day for months and months. Many months later, not being knowledgeable about machinery types, I had a piece of dry pistachio mounted to turn a bowl. The wood was very hard and I took a break for lunch. Hit the off switch, the lathe stopped and I was off to eat. When I came back, I decided to do a little cleanup of the lathe and floor with the shopvac. Had just finished when I leaned against the lathe with my arm near the headstock and the lathe started with the switch in the off position. My arm was instantly a bloody mess from the spinning wood. I wrapped my arm with paper towels and headed for the first aid kit. After washing all the damaged area, mostly hanging skin, and treating, I went back to the shop and the lathe and killed the power. I took the switch off the lathe and it was almost completely plugged with shavings accumulated inside the switch. KEEP the ON/OFF SWITCH CLEANED OUT! I have "modern art" scars on my arm as a constant reminder!

Re: On the subject of shop accidents:

#17

Re: Simply Stated

Bill Neddow

Tom, about a week ago, I found fantastic fingerless gloves for the type of heavy-duty turning you are talking about. They are solid leather -- which means you get excellent coverage of the area between your little finger and your wrist. Normally, the leather on the palm is sewn to some very thing flexible material here -- and only half of this area is adequately protected.

These gloves are sold in the Honda motorcycle accessory shops. They are not only fingerless but also skin tight.

Please do not use loose gloves with full fingers around a lathe.

Re: On the subject of shop accidents:

#18

Re: Simply Stated

Tom in Alaska

Bill - thanks for the tip. I'll check out the motorcycle shops here to see if I can find any. Do you have issues with your hands getting too hot in tight leather gloves?

I like the open mesh fabric on the gloves I use. I suppose I could sew on a leather side, but then I wouldn't have that "classy" look that only Duct Tape can give... :-)

Re: On the subject of shop accidents:

#19

Re: On the subject of shop accidents:

Roger

Back in the mid 60's our industrial arts teacher said growing up he and his brother worked as a team of carpenters. He told us that one would do the measuring and sawing and one would do the nailing. Well this teacher was/is missing his left thumb and most of his index and middle finger on his right hand. I've always hoped he was the one doing the sawing and that he didn't lose his fingers and thumb to a hammer,OUCH!! He would take the nubs of his index and middle finger and grab those who were misbehaving or not paying attention by the ear and take them all the way to the office for discipline. The office was about as far away from the ind. arts shop as possible. This teacher was 6'9" so he would keep you on your tiptoes the whole way. Nowadays he is one of the oldest and most respected turners in our club. Needless to say, when he does a demo. I pay attention. My ears are too old to take much pinching.

Re: On the subject of shop accidents:

#20

Re: Simply Stated

Bill Neddow

Hi Tom.

I have never had an issue with heat in the all leather gloves. I would prefer a mesh -- but I get speared with big slivers when I am using a mesh-backed glove.

I have tried getting a shoemaker to sew a bit of very flexible leather on the back of mesh-backed gloved in the years when I could not find the all-leather gloves. This works well. But, as you say, it does not have the "classy" look of good duct tape. :D

Bill

Re: On the subject of shop accidents:

#21

Jesper, Denmark

Re: Simply Stated

Jesper, Denmark

Bicycle and sailing gloves without the fingertips are excellent too.