Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Not the appropriate use of a skew

Posts

Not the appropriate use of a skew

#1

Not the appropriate use of a skew

Mike Foster

I had a new turner stop by my studio today and I happened to be in the shop. He was interested in turning and was obviously a rank beginner. He has been turning using information he has picked up off the web, and little else. He has a smaller older craftsman lathe and has been turning some rolling pins and small bowls.

After talking a bit he showed me his forehead and told me this had happened just recently. What you see in this picture is only the shiner that went along with the laceration under the bandage that took 20 stitches to repair.

This was just scary. He went to my tool rack and picked out a skew, and said that this is what he was hollowing the bowl with when it happened (didn't know what it was called or what it was intended for). He said the skew snapped off at the shank, and he hasn't found the part that went flying. Did I mention, no face shield? Well I showed him a little turning the right way, but really, really, really pushed him to join a club. He lives in Tewksbury, MA which is close to the last NE symposium site, and I would guess there are a couple of clubs near him. I gave him an AAW magazine and a Packard catalog and told him to join a club again.

I don't think he has a clue how lucky he is. That skew could have done far worse damage.

BTW, his wife went out and bought him 2 face shields after the incident. I told him that wearing it should become a religion.

So this is a much different story than the video that John shared below. At least that turner was wearing a shield and was standing out of the line of fire using an appropriate tool. I just hope this turner gets a little more education before something else happens.

Re: Not the appropriate use of a skew

#2

Re: Not the appropriate use of a skew

John Lucas

Mike I had a new turner on another newsgroup describe the tools he was using to hollow a bowl and he said he used a skew. He was using it as a scraper. I warned him about the dangers and sent him links to some of my videos. I really really need to get a bowl turning video done.

Re: Not the appropriate use of a skew

#3

Re: Not the appropriate use of a skew

ihmserv

mike

don't know if you have this guys contact info. but if you do his local chapter is

A.R.T. - american revolutionary turners.

based in woburn mass.

there web site is for more info is:

http://www.revolutionary-turners.com/

IAN

Re: Not the appropriate use of a skew

#4

Steven Antonucci

Unsafe at Any Speed

Steven Antonucci

I use a skew as a negative rake scraper on a bowl. I don't think his issue was the wrong tool. I'm guessing that his issue is that he shouldn't be standing at a lathe at all (until he gets some help).

You have to basically be doing everything wrong to break a tool. Speed to fast. Toolrest too far away. Long overhang of the tool. Face too close to danger.

It pains me to see the efforts that some people post to YouTube. I understand their enthusiasm and that they don't know what they don't know, but you never see the results of people have viewed their videos and assumed that they were watching an expert. Before undertaking any new skill, I watch 3-4 videos to make sure that I have seen a cross section of wasy to do something. If the person looks like he's fighting to get it done, it usually means you should move to the next video.

If it looks easy, the person demonstrating probably knows what they are doing. I caution people that it looks easy because they haven't seen the 10,000 hours that preceded it.

Glad that he will survive. Hope you can get him some help.

Steve

Re: Not the appropriate use of a skew

#5

Alan Zenreich

Re: Unsafe at Any Speed

Alan Zenreich

And of course, there's always some guy trying to hand hold a camera while demonstrating lathe techniques...

< ducking >

Re: Not the appropriate use of a skew

#6

Steven Antonucci

and a guy in body armor turning pendants 


Re: Not the appropriate use of a skew

#7

Alan Zenreich

Re: and a guy in body armor turning pendants

Alan Zenreich

I haven't seen that on Youtube.... yet

Re: Not the appropriate use of a skew

#8

Steven Antonucci

'cause there is no evid. that you actually turn 


Re: Not the appropriate use of a skew

#9

now, boys, play nice!


Re: Not the appropriate use of a skew

#10

Monty Python

Mark Mandell - Gone Round In New Jersey

Here we come! [er, go, um . . . stay still?]

Re: Not the appropriate use of a skew

#11

Steven Antonucci

Inside joke

Steven Antonucci

Alan knows that I have seen him turn once before, so he no longer has to prove it. I've been in his shop and seen both lathes. Granted, I have more sawdust in my underwear at this writing than he has ever created on the lathe ;)

Steve

Re: Not the appropriate use of a skew

#12

Re: Inside joke

Mark Mandell - Gone Round In New Jersey

Would that be inside his shop or inside your underwear?

:D :D

Re: Not the appropriate use of a skew

#13

Steven Antonucci

I'm not wearing any


Re: Not the appropriate use of a skew

#14

Alan Zenreich

Re: Inside joke

Alan Zenreich

Hey, there are 4 lathes in that shop room. How soon they forget.

When I said I hadn't seen that on YouTube yet, I was referring to the fact that I haven't appear in armor on YouTube yet... images of me are quite rare, you know.

Re: Not the appropriate use of a skew

#15

Alan Zenreich

Re: Inside joke

Alan Zenreich

Is that like shooting an elephant in your pajamas?

Re: Not the appropriate use of a skew

#16

Re: Monty Python

Don in Central Illinois

As Grouch would sat, "How did the rkephant get into you pajamas?"

Re: Not the appropriate use of a skew

#17

Steven Antonucci

I can attest to the difficulty of shooting...

Steven Antonucci

while turning. Hence the rarity of images of you in body armor, I suppose?

P.S. You should plan on heading up to Peters Valley on Aug 31. Keith Tompkins will be teaching that weekend, and WGW snagged him for our Friday night meeting.