Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

Morning lamp report

Posts

Morning lamp report

#1

Morning lamp report

John Lucas

Starting the big glue ups this morning. I got all the rings glued up yersterday and will start flattening them this morning after I go vote. Well I might take a good hilly bicycle ride first and give the big glue up time to set so I can figure out how to glue the 3rd panel in place.

Then I have to figure out how to temporarily attach the door so I can turn the whole thing. I may use a paper joint but need to do a test. I would have to separate the paper joint using something like a guitar string pulled down through it. I usually drive a knife down and the joint pops apart. I don't think there will be enough flex to do that so I'll run a test on the guitar string method. If it doesn't mess up the wood that should work and would be much more stable for turning.

Re: Morning lamp report

#2

Re: Morning lamp report

Stuart Johnson

John, what about using hide glue for the door joints? After turning I think you could lay some warm wet strips of rag along the joint and then pop them apart. Another possible way is to use a heat gun or hair dryer to soften the glue.

Re: Morning lamp report

#3

Steven Antonucci

Why glue it?

Steven Antonucci

If you are worried about getting it back apart, why glue it in the first place?

You have plenty of length to place a few band clamps and turn between them, and then readjust them after you have finished an area to finish under them.

Steve

Re: Morning lamp report

#4

Alternative

Mark Mandell - Gone Round In New Jersey

On Steve's good premise:

Seal the joint faces well with shellac, then a bit of paste wax. Apply a half dozen pieces of thin double-face tape along the length, then wrap at 4 points with strapping tape (with the fiber strands). Turn. Remove the strapping and rewrap in alternate spots to finish the turning.

This way you won't have extraneous cord or straps coming loose and the temp joints will have some measure of stability against shifting but stile come apart easily.

If you don't already have one, I'd also suggest you make up a full-length tool rest that you can set once and then leave in place. Maintaining that long taper line without slight bellies or coves will be much harder if you have to keep inching a 12" tool rest along the bed.

Final note: If you're going to use concealed Soss hinges, it'll be easier to cut the mortices in the facing pieces if you do them before the glue-up.

Re: Morning lamp report

#5

Re: Alternative

John Lucas

It's tapered so band clamps would not work. You would have to glue on some kind of stop blocks to hold the clamps in place.

Strapping tape is a possibility.

Since I have to put some sort of disc on both ends to center the lamp I thought about just putting screws in. The downside of that is I would have to fill the holes in the backside of the door from the screws.

I glued up a test paper joint this morning while gluing up the rings. I'll give that test piece a try. If it works, problem solved If not, plan B.

Mark I 'm not going to use hinges. I was originally but decided just putting the panel in and sliding the rings over will be enough to hold the door shut.

Re: Morning lamp report

#6

Re: Alternative

Keith Newton

You are probably better at spindle turning than me, but like Mark suggested, I made a full length tool rest. Then I ran my big Makita power-plane down it askew, with the infeed bed removed, to give more cutting depth.

Instead of a paper joint, I could just saw down any of the glue-lines with a circular saw, or use my long sled on the TS. I have one 8' long which I made for cutting stacks of veneers, but also comes in handy when it is needed for odd projects like this.

I'm not sure why you are reluctant to just screw on plywood end-plates to mount it, but that is what I would do.

Re: Morning lamp report

#7

Re: Alternative

John Lucas

Keith Wouldn't that leave an a kerf that would have to be filled. With the Paper joint all I have to do is clean off the glue and paper using White vinegar and the joint should close up. I'll let you know because I think that's the way I'm going to go. I tried a test today and my knife that I drive through the paper only flexes the wood about 1/16 or less. I think it can handle that.

I thought about planing the wood but it has some squirly grain and I'm a much better turner than I am at planing. :)

Re: Morning lamp report

#8

Steven Antonucci

Band clamps with wedges?

Steven Antonucci

If you cut a couple of wedges and slide them in, it shold resolve any holding issues you think you'd have. No glue, just the band holding them.

I would also hazard a guess that the clamp would hold on a taper, since it isn't really all that tapered along the 1" width of the strap...

Keepin' it simple.

S