Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

Spalted Pecan Bowl

Posts

Spalted Pecan Bowl

#1

Don Leydens

Spalted Pecan Bowl

Don Leydens

This piece of spalted pecan came real close to being firewood (or pens). Key word being spalted. Kept on going anyway and this is what it turned into. 11" x 2.5" tall. My main objective was to make the sloping bowl bottom look like it was coming straight through the top. You can kind of see it in the very bad photo below.

Thanks for looking and all comments are more than welcome, Don


Re: Spalted Pecan Bowl

#2

Lovely

Mark Mandell - Gone Round In New Jersey

Finish does much for the grain.

Re: Spalted Pecan Bowl

#3

Mike Stafford

Re: Spalted Pecan Bowl

Mike Stafford

Very nicely done, Don. The finish is lovely. With this much spalting did you have to deal with much punky wood?

Normally people complain about how hard pecan is but spalted woods can be much more difficult to turn.

Re: Spalted Pecan Bowl

#4

Don Leydens

Re: Spalted Pecan Bowl

Don Leydens

Thanks Mark!

You nailed it Mike! Between the hard pecan, spalt lines and all the punky parts (many), getting an even cut (not to mention sanding) was a challenge. It was a good teaching piece though. I think I learned a lot by continuing with it.

Thanks for the comments,

Don

Re: Spalted Pecan Bowl

#5

Yo, Punk!

Mark Mandell - Gone Round In New Jersey

An application of thin epoxy can make punky wood behave, if you're so inclined. I use either System Three Mirror Coat or Park's Glaze Coat which are thinner resins. For infusing into rotten wood, you can also thin it further with a little DN Ethanol; "little" as in not more than 5 percent. You can't do this however, if you're filling holes where the resin will set in a block because the reaction heat will boil the alcohol and you'll wind up with epoxy foam that's a mess to dig out and redo. DAMHIKT ;)

Re: Spalted Pecan Bowl

#6

Don Leydens

Re: Yo, Punk!

Don Leydens

Thanks for the tip, Mark. I was reading about that (maybe by you) earlier this morning and I printed out the info. Worth trying on the next punky piece. Shellac and/or CA glue just didn't cut it on this one.

Don

Re: Spalted Pecan Bowl

#7

George Taylor

Very cool Don

George Taylor

I am always pleasantly surprised with whatever you come up with ... very nice piece.

George

Re: Spalted Pecan Bowl

#8

Re: Spalted Pecan Bowl

Bill Howatt

Very nice. It almost looks like the bowl is rising from the surface.

Bill

Re: Spalted Pecan Bowl

#9

Dale Jablonski

Re: Spalted Pecan Bowl

Dale Jablonski

Beautiful piece Don, great work.

Re: Spalted Pecan Bowl

#10

Re: Spalted Pecan Bowl

Hal Taylor

A real beauty Don. The wood is a beaut too.

Re: Spalted Pecan Bowl

#11

Don Leydens

Re: Spalted Pecan Bowl

Don Leydens

Thanks for the kind comments guys. It's much appreciated.

Don

Re: Spalted Pecan Bowl

#12

Re: Spalted Pecan Bowl

Terry Scott

Lovely wood and nice work

Id like to see a ve in the wings down to the rim of the bowl.But dont cut them off like I do for the mantaray

Re: Spalted Pecan Bowl

#13

Don Leydens

Re: Spalted Pecan Bowl

Don Leydens

Terry, I agree 100%. Had the wood not been so punky, I would have tried it. I tried something like that a while back and loved the way the piece was coming out, till a catch blew two of the legs right off. Next time I get some solid (and dry) wood in this general shape, I'll try that out.