Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Sparcity of clubs in some states *LINK*

Posts

Sparcity of clubs in some states *LINK*

#1

Sparcity of clubs in some states *LINK*

John Lucas

I was checking the AAW map on clubs and it's very interesting. I was wondering why there aren't very many clubs in Kentucky. Look at the map. Tennessee, Georgia and North Carolina have a huge number. Some states it's obvious why, the population numbers and size of the state make it obvious but I would think Kentucky would have the same rough population as Tenneessee.

I'll ask my friend Paul Ferrel tomorrow. He lives in the far west corner of Kentucky and is a fantastic turners who's made a living turning for a very long time. There aren't any clubs anywhere near him.


http://www.woodturner.org/community//

Re: Sparcity of clubs in some states *LINK*

#2

Steven Antonucci

Edit the link (extra / on the end)


Re: Sparcity of clubs in some states *LINK*

#3

Could not edit so here's an image

John Lucas


Re: Sparcity of clubs in some states *LINK*

#4

Maybe it's an upper middle class hobby

Dick Coers

Using $4,000-$7,000 lathes and a couple thousand dollars worth of tools and chucks limits the folks that want to belong to an AAW club these days. Add this to what appears to be promotion of high end art objects (as seen in the sales section of the forumn) by the AAW, and I think you may begin to see that it takes larger metropolitan areas to carry a club. I know guys that make their own tools, and turn on a Shopsmith, but I'm guessing they are in the minority in the AAW.

Re: Sparcity of clubs in some states *LINK*

#5

Re: Maybe it's an upper middle class hobby

John Lucas

I don't think so. I know a lot of guys who turn on mini lathes and the less expensive ones. In fact in 2 of the clubs that I'm in I'll bet very few have lathes over 700 dollars. The serious guys in the club do of course.

I will admit that woodworking as a whole is not a cheap hobby. However you can get into turning fairly inexpensively. I'm looking at getting my dad into pen making. If done at the low level I think I can get him most of what he needs for $500 to $600 dollars. He does already have a shopsmith which he can use to drill and sand pieces.

I know I hear all the time about the AAW putting only high end work out there but let's be honest. How many bowls can you look at. After the first 30 or 40 it gets pretty dull. I think it's fun to see what other projects people come up with. Heck even the lowly finger top can go to extremes if you look at the latest issue of the magazine. Makes me want to go to the shop and play.

Re: Sparcity of clubs in some states *LINK*

#6

Re: Maybe it's an upper middle class hobby

Dick Coers

I have to start shopping where you do. The cheapest Jet mini lathe at Amazon is $429, add a knock off chuck $110, Harbor Freight tools $75, grinder $115, Wolverine $100, and you are over $800. Then if you go on ANY internet turning site, AAW included, they will tell you that several of the items I mentioned will not get the job done. They will tell you to buy $100+ carbide chisels, One-way or Vicmarc chucks, $500+ hollowing rigs, and you're $1000 without breaking a sweat. So maybe I'm way off base with this, but if you go to a AAW symposium (national or regional) you'll maybe only find a couple of simple project seminars, and I've never sat in one that tells you to use an absolute minimum of cheap Harbor Freight tools in your turning. How about the look of the instant gallery, or the vendor area? Nothing cheap there! With the exception of the youth instruction, AAW is all about high turning achievement and newer, higher end tools. Again, don't get me wrong, I love every minute of it, and my membership number is 1241. But if I had a couple kids, was working for $12 to $14 an hour at one or two jobs, and lived in rental house in a small town, I'm not traveling 50 miles to join an AAW turning club. I hope this isn't taken as a slight to any state, but just my thoughts of why there aren't more turning clubs in some areas.

Re: Sparcity of clubs in some states *LINK*

#7

Re: Maybe it's an upper middle class hobby

John Lucas

Keep your eyes open for used equipment. I have yet to pay over $300 for a mini lathe and have bought several Jet or Rikon's in this range. Although I recommend people buy just a few good quality tools Like P@N or Packard brand you can get a set of tools from Harbour Freight for less than $70. They will need to be reground to be decent tools but they aren't terrible. I own several.

You don't need an expensive grinder or a jig. I did all my early sharpening on my old belt sander or a disc I attached to the lathe. A simple 1/2hp cheapy with a gray wheel will work. I know I used for many years before finally buying white wheels for it and it was many more years before I stepped up to a 3/4hp slow speed grinder.

Sure we like to tell everyone to buy the latest greatest. It makes turning more enjoyable but it certainly isn't absolutely necessary. I turned for 10 years or more without a chuck. Those are nice but again not essential.

I think the turning clubs are great. I belong to 3 and often travel to 2 more. I go 20 miles to the local one, 47 to the one we originally started and 90 miles to the big club. I will occasionally go to Knoxville or Chattanooga if I have time which are slightly further. You can't hang out with a nicer crowd and you always learn something.

Re: Sparcity of clubs in some states *LINK*

#8

Lyle Jamieson

Re: Maybe it's an upper middle class hobby

Lyle Jamieson

To me its all about the basics. One of my rotations at San Jose was the foundations of bowl turning. It was all about tool control, preventing catches, vibration issues, and torn out grain. I used a deep fluted bowl gouge from start to finish, never picked up another tool and did not use a chuck. I think most of the nationally known turners you see at any symposium have a signiture work that usually uses techniques off the lathe. But when they demonstrate, most start with teaching the turning skills necessary to get where they go. My teaching concentrates on the process, not the finish product. I teach how to turn and let the student take the basics in whetever direction that pleases them. Its all about the fun. I often quote Michael Hosaluk when he said, " How do you tell a beginner from an advanced turner?? You can tell by what they do with the basics."

There was a young 16 year old that visited our club meeting to show us his exquisitely turned Harry Potter wands. Come to find out he turned them on a drill press with home made tools.