Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Need some ideas

Posts

Need some ideas

#1

Need some ideas

D. Hansen

Looking for some innovation and or ideas to solve a dilemma. Here is the situation. I turned a 12" or so cherry natural edge bowl. Turned out very nice and I don't want to relegate it to the fireplace. When I turned off the bottom I ran in to an unexpected worm hole. (maybe i should call Morton Freeman??) . The vacuum chuck pulled a portion of the center of the bottom in along the worm hole so now I have a funnel.

I thought about turning a stepped bottom of some sort and epoxying it to the bowl like a step. Maybe turn a small tennon to fit the bowl bottom and do some chatterwork or carving so that when installed the inside of the bowl would have a decorative item in the bottom. I could also just make a cabochon and glue it over the hole I guess.

I have a set of cole jaws but have never used them. I was thinking about mounting the bowl in the jaws and turn the hole crack circular so the new stepped bottom tennon would fit the hole.

The problem is that the bowl top is irregular. It is natural edge with bark all around it. Although I have not worked out the details I kinda think the bowl will not be stable enough in the cole jaws to allow me to make the hole neat enough for the tennon. I thought about making a donut chuck but it would probably present the same problem So I thought that maybe someone on W/C might be able to suggest some things I could try to salvage the bowl. thoughts ideas and or suggestions welcome.

Re: Need some ideas

#2

Re: Need some ideas

Greg Haugen

At one time, when I made a donut chuck (the technical term is escaping me presently) I made an option for examples like this. I used a piece of PVC and an old computer's mouse pad in the center of the base so the bowl would sit on the pad and PVC like a vacuum chuck so the irregular rim would not be touching anything thus throwing it out of whack but the donut could still come around the bowl and hold it in place. It worked really well for reversing NE bowls without a vacuum or one with voids where a vacuum would be useless. I no longer have the chuck unfortunately, so I can't post pictures.

Re: Need some ideas

#3

Re: Need some ideas *LINK*

Dave Paine

You could make a plywood or MDF wood chuck. This has a backplate and a second plate connected by rods. You could use wedges under the natural edge to get the bowl aligned.

In the link below look for "Centering Donut Chuck for Reverse Turning"


http://turnedwood.com/tools&jigs.html

Re: Need some ideas

#4

Jam chuck and tape

Lloyd in Mississauga

Could you take and mount a waste block with screws to your cole jaw or chuck and turn it to fit just inside the body of the bowl and not contacting the bottom. Then put masking tape over the bowl, and then strap tape around that and the chuck or cole jaws to hold the bowl on? The masking tape will peel off the bowl without leaving marks better than the stickier strapping tape would. You could also use duct tape instead of strapping tape.

That would leave the bottom accessible to turn away with light cuts.

If you were looking to add on a new bottom and turn it down, then I would likely look at the donut chuck as it would provide a bit more stability to make heavier shaping cuts.

Lloyd

Re: Need some ideas

#5

Re: Need some ideas

charlie belden

"I was thinking about mounting the bowl in the jaws and turn the hole crack circular so the new stepped bottom tennon would fit the hole. "

If the bottom is flat, and there's some meat around the hole, turn a waste block with a short tenon about the thickness of what's left on the bottom of your natural edge bowl - PLUS 1/8" or so. Make the tenon's diameter smaller than the hole in your natural edge bowl. Double back tape it to the bottom of your bowl.

Now you have solid wood for the center of a forstner bit to register into - BEFORE it starts cutting wood. With an awl, poke a hole into this waste block where you want the center of your hole. On a drill press, align the forstner bit to the hole and drill our your circle in the bottom of your bowl. Make repeated light cuts until you're through the bottom of the bowl ready for your turned plug.

You're idea to put a cabachon over the hole sounds a lot easier and would be really interesting.

Re: Need some ideas

#6

Re: Need some ideas

John Lucas

Make a doughnut chuck with a tube. Take your cole jaws and place a ring of PVC large enough so the bowl will sit down in it without bottoming out on the cole jaws. Now put another ring in the inside of the bowl that's tall enough so a plywood doughnut that will go on tip of this won't touch your natural edge. Run long screws (I make mine out of all thread rod) through the doughnut and down into the grooves in your cole jaws.

Positioning the natural edge will take some fiddling but once it's positioned you should be able to turn a hole in the bottom with a rebate in the top and install a new bottom.

Turners will know what you did but customers don't care. One of my good turning buddies here makes a whole line of pieces with contrasting wood in the bottom and they sell well. Ideally you should line up the grain so the wood movement will be the same but My friend doesn't even do that. There is a slight gap in some his pieces due to uneven wood movement but again, the customers don't care. In fact they like the contrasting woods.

Re: Need some ideas

#7

Re: Thanks


Re: Need some ideas

#8

What I did

D. Hansen

Thanks for the suggestions. I realized that since the bowl was in the finishing steps the bottom was flat. When the cole jaws were fully opened the chuck jaws were wider than the intended hole So I put the bowl in the chuck bottom against the jaws instead of top in which I was worried would not be even. It worked easily to cut the hole from inside the bowl.