Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Price drop on over 1300 Rockler items

Quick Change Tool Handle Source?

Posts

Quick Change Tool Handle Source?

#1

Quick Change Tool Handle Source?

charlie belden

Tool handles that use set screws to hold a round tool have a problem. The set screws dimple the tool or a sleeve holding the tool - making getting the tool out, and later back in, well let's just say Less Than Effortless. Sometimes resorting to vise grips is necessary, or some filing the dimples on the tool shaft.

When Graeme Priddle demonstrated at our turning club, he had a quick change tool handle. Turn the gnurled collar/ferrule to loosen or tighten the tool in the handle. Quick, easy and apparently good gripping. Seemed like it used something like a quick change drill mechanism. I beiieve it also could handle a range of tool shank diameters.

Anyone know if this quick change handle is available now, and if so, from whom?

Re: Quick Change Tool Handle Source?

#2

Re: Quick Change Tool Handle Source? *LINK*

John Kaner

Charlie,

When Jimmy Clewes demonstrated here, he used some of his design and manufactured by Doug Thompson. They are well built and solid. Quick and easy tool changes. Hopefully, a link is attached. If I failed, his home page has them listed under tools...


http://www.jimmyclewes.com/tools.shtml

Re: Quick Change Tool Handle Source?

#3

Ken Vaughan

Kelton Quick Change Tool Handle Source?

Ken Vaughan

They come in three sizes -- ER 32, ER 25 and ER 16 machinist collets hold the tool.

Very firm grip on the tool -- and fast change of collets/tools as needed.

The down side is that you need a collet to match the tool sizes you use but you can go from 1/8 inch to 3/4 inch with one tool handle.

Re: Quick Change Tool Handle Source?

#4

Re: Quick Change Tool Handle Source?

John Lucas

Boy you must be using a lot of pressure. I have the Thompson handles and use them with his tools and the Hunter tools. I have never had a problem with denting the metal.

I like Jimmy's handles but have not owned one yet. I do have some tool handles made by a friend in Chattanooga and some I made that use R8 collets. These are excellent and hold extremely well. The downside is they have very limited size ranges, I think about +/- .010" so the shaft sizes of the tools need to be pretty exact.

I believe someone also markets a handle with a quick release used for routers. Those are only available in 1/4" and 1/2" I think.

Re: Quick Change Tool Handle Source?

#5

Bill Blasic

Re: Kelton Quick Change Tool Handle Source?

Bill Blasic

Along with the Keltons there are the Woodcut Twin Collet Handles. JoHannes Michelsen has a collet system for some of his handles. Serious Tool Works has the Serious Camlock Handle and as stated the Clewes Camlock Handle (made by Thompson) are all available. There are quite a few choices. As I use Thompson Tools for 90% of all my turning I have never had a problem with the grub screw causing any damage to the tool allowing for unrestricted removal and replacement of the steel in any handle.

Bill

Re: Quick Change Tool Handle Source?

#6

Alan Zenreich

Re: Quick Change Tool Handle Source?

Alan Zenreich

you also might consider changing the grub screws to those made of ofter metal.

Re: Quick Change Tool Handle Source?

#7

Steven Antonucci

Or putting a small paper washer on the end.


Re: Quick Change Tool Handle Source?

#8

Re: Quick Change Tool Handle Source?

charlie belden

Thanks to all for such quick responses.

I thought if was Graeme that was using a quick changer but it was, in fact, Jimmy Clewes. Must be getting old and memories are starting to jumble ; )

Jimmy is demonstrating in the Doug Thompson booth at the SJ Symposium and I was just visiting with him at the show yesterday (forehead slap). Got to meet Vicky Jordan and picked up the 18" handle I should have chosen rather than the 12" when I bought John's hollowing tools a year or so ago. Also picked up three of Cindy Drozda's little live center tips while I was at it. They'll come in handy since I'm doing a lot of small stuff lately. Told her about the Guadalupe River Park a block from the symposium site since I know she's a runner.

The Symposium is putting me in sensory overload. So many demonstrators, so many exhibitors, so many tools and so much wood. It's going to take at least a month to recover and a year to rebuild the bank account!

Re: Quick Change Tool Handle Source?

#9

Re: Quick Change Tool Handle Source?

Tom in Alaska

I understand that Jimmy Clewes may be coming out with a new cam collar that will be "bottomless", allowing one to use a double ended gouge in the handle. That would be nice.

Re: Quick Change Tool Handle Source?

#10

Get some brass tipped set screws

Ray - Middletown, in

from McMaster-Carr. No more dings.

Ray

Re: Quick Change Tool Handle Source?

#11

Serious Camlock Handle

David Walser

I use and endorse the Serious Camlock Handle. A 1/8 turn of the cam nut locks the tool in place. A 1/8 turn in the opposite direction frees the tool. It couldn't be simpler.

Here are some additional comments, both pro and con:

* I like the balance and feel of the handle. The foam grip does a good job of absorbing any vibrations. Yet, you still get a good feel of the tool's edge cutting into the wood.

* The handle uses collets to adapt to different tool shaft sizes. Changing from one collett to another is quick and easy, but I'd still recommend having one handle for 3/8" shafts, another for 1/2" shafts, etc. The collets are far too easy to lose among the shavings. (At least they are in my shop.) Besides, having to switch from one collet to another limits the quick change benefit of the cam lock.

* The collets do NOT have much adjustment capacity. The shaft size of the tool needs to be fairly close to the stated size or the collet might not grip the tool securely. I have an off-brand tool with an undersized shaft that is nominally 1/2" in diameter. I have to turn the cam nut close to a 1/4 turn to secure the tool. If the shaft were a little more undersized, I doubt the cam/collet would secure the tool.

* The collets allow you to slide the tool as far into the handle as you would like. This makes it easy to "choke up" on a tool or to extend it out for more reach. It also enables you to use double-ended tools. (My serious 1/2" spindle gouge has a flute that runs the full length of the tool. This enables each end to be ground to a different shape. I like this feature.)

* The cam locks with a 1/8 turn in either direction. If you don't always turn the cam in the same direction to lock the tool, it's easy to turn the cam in the wrong direction when trying to free the tool. This can easily make the cam too tight to unlock by hand. The cam and the handle body are marked to show the unlocked position. These markings are fairly faint and can be easily obscured by dust, so I've accented the marks with a Sharpie. Even still, when first using the tool, I'd forget to look and would inadvertently lock the tool into the handle. Just remember, if the cam resists turning, you're turning it the wrong way! Light pressure is all it takes to secure the tool and light pressure should be all it take to unlock it.

* The tool handle is round and is basically the same diameter from one end to the other. (Only the cam at the front of the tool is of a different diameter.) Unlike a custom made wooden handle or some of the other interchangeable handles on the market, there's no tactile feedback to let you know where you're gripping the handle or to know the direction of the flute. The handle will also roll off your lathe or bench.

* The handle is hollow it's full length. While this allows you to use double ended tools and to extend your tool the length you'd like, there is no ability to add lead shot or some other ballast to the tool. I don't like using such ballast, it makes the tool feel "dead" in my hands; but if you want to use lead shot, this isn't the handle for you.

* The handle does not accept extensions. It only comes in one length. At about 18", the handle is an acceptable length for most applications. But, it can be too short or too long for other uses. This cannot be the only handle in your kit.

HTH

Re: Quick Change Tool Handle Source?

#12

Re: Quick Change Tool Handle Source?

charlie belden

I'll be sure to ask him about that tomorrow. I suspect that if you cut off the end of the existing design - and drilled a tool handle deep enough to accomodate a two ended tool . . .

I bought and iPad2, then took it back and got a refund because of the fact that I'd have to buy apps online using my debit card - something I did not want to do. Set up a separate debit card account for online purchases only - but it couldn't be activated in time to get some apps and test the iPad2.

Three weeks later, the New iPad came out. at the same price, and the iPad2 price dropped $100.

I don't buy the NEW & IMPROVED 'til they've been out for at least a year. But in the computer world, if you wait another year, you're probably going to have a NEW & IMPROVED model out within 6 months, often for less money.

The rate at which new turning tools and accessories are coming out, it's soon going to be like the computer, cell phone and tablet/iPad market. If you already have it - it's practically obsolete.

Re: Quick Change Tool Handle Source?

#13

Re: Kelton Quick Change Tool Handle Source?

Carole Valentine

Handles are a pretty personal thing, but I'll second the Kelton ERs. They are the only handles I use any more. I like the fact that they they can be combined for about any length you need. Even the little torque arresting handle can be used as an extension on the ER16 to give it some extra length if desired. Sometimes when hand hollowing I combine handles so I can tuck it up against my side or under my arm. The tool can be inserted as far or as little as you wish. The ER collets are readily available in about any size you could want - metric or imperial. The ER25 and 32 have a sealed compartment for adding weight but I have not really found it to be necessary with the turning I do. They are really easy on my hands too - no more visits from "Arthur" after a day of turning!

Re: Quick Change Tool Handle Source?

#14

Re: Quick Change Tool Handle Source?

Don Evans

I've never seen that problem either. I wonder if you are getting this problem with "home made" tools where the whole tool isn't hardened?

Never seen an allen screw dent a RC58 or higher hardened tool.

You can just purchase a brass rod, cut of 1/16" thick wafers that will drop down in the screw hold and it will stop the problem with home mades. Or as suggested buy some screws with brass or plastic (neophrene?) tips.

You can also purchase the ER collets from all the industrial suppliers like MSC, enco, etc.

You can also purchase these and other collets that are not drilled out so you can make a collet any size you can drill.

Personally, I like a handle on every tool and have never had a problem with just a conventional wooden handle.

Don

Re: Quick Change Tool Handle Source?

#15

How about the twist lock on Dougs handle?

John Kaner

Doug has a great handle, use shot or not. Jimmy has the twist lock system through Doug. This way you can have fast changeover for demonstrators and use double ended tools...

Re: Quick Change Tool Handle Source?

#16

Jimmy's THROUGH Quick Change Handle

charlie belden

Jimmy wasn't in the booth when I stopped by again so I asked Doug Thompson if Jimmy would be coming out with a THROUGH version of his quick change handle. The answer I was given was "NO".

The SERIOUS Colleted Through Handle is probably what I'm looking for. Having depleted my Toys Acquisition Budget - for the year - a pair of SERIOUS Through Handles will have to go on next year's Toys Acquition Budget.

Thanks for the VERY thorough review

.