Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Getting a Pacemaker next Monday

Posts

Getting a Pacemaker next Monday

#1

Jerry Louden

Getting a Pacemaker next Monday

Jerry Louden

Just wondering how many of you out there have pacemakers and if you experience any problems or observe any cautions when working on the lathe. The manufacturer of the pacemaker says you need to maintain a distance of 2 feet between the motor and the device. I'm okay on my larger Delta 1440, but the motor on my Delta midi is right under the working area and at best would be a foot from my chest. It is not in my plans to give up turning so I guess I will have to get tools with longer handles. :) I would apperciate any suggestions or advice. Jerry

Re: Getting a Pacemaker next Monday

#2

Re: Getting a Pacemaker next Monday

john lucas

Jerry I hear this quite often and I've always wondered if you could build a sort of Faraday cage around the motor to keep the problem at bay. It's been a 100 years since I took my electronics classes so I may even have the name incorrect.

Re: Getting a Pacemaker next Monday

#3

Re: Getting a Pacemaker next Monday

George Scott

It is an interesting experience. They don't put you to sleep but you are totally unaware of what is happening. To answer your question...I have a St Jude ICD (implanted cardiac device) and I was told nothing except not to raise my left arm above the shoulder for the first six weeks. They don't want the leads to tear loose. Since then I have been totally active. Cut up a cherry tree yesterday. I also have a Delta midi plus a 2442 Powermatic. in use all the time. I also have a fully equipped wood shop and several large machines. It's been two years and nary a problem. Also know two other turners with cardiac devices and they have never mentioned being limited.

Don't spend a lot of time worrying about it.

Re: Getting a Pacemaker next Monday

#4

Re: Getting a Pacemaker next Monday

bill Crommett

Check out with a physicist about the prospect of making a copper screen vest to route any strays around your body.

Re: Getting a Pacemaker next Monday

#5

Re: Getting a Pacemaker next Monday

Roger Chandler

My wife works in the cardiac device clinic for the cardiology group here and programs the pacemakers, ICD's [internal cardiac defibrolaters] Bi-V-ICD's etc.

From my limited knowledge....listening to her and her factory reps speak on this subject........it depends on the device and the electronics in your lathe. A pacemaker does not give shock therapy to the heart.......it just paces. Many turners do turn with these......

In the case of an ICD.......your cardiologist can write an order for a test to be done with you hooked up to the monitor and your lathe on......if it has remote transmitting capabilities, then perhaps the device clinic or factory rep could monitor you while you attempt to turn something to see if there is any pick up by the ICD.........the monitor/programmer will pick up interference if there is.

This should be discussed with your cardiologist and the factory rep.......especially if the electronics in your lathe are shielded........you likely will be safe after your leads are fully healed, and again .........follow your Doctor's advice!

Re: Getting a Pacemaker next Monday

#6

Re: Getting a Pacemaker next Monday

Bill Howatt

Given that the pacemaker manufacturer has a warning, you should look further into the situation. You don't want your heart rotating at 1500RPM!

In my view, which is worth exactly what you are paying me for it, I wouldn't think a regular motor was a big deal but I'd be concerned about VFDs and motors because of the high harmonic content and power of the drive currents. They certainly interfere with radio reception! A lot of this interference goes back out the devices power cord and it uses the house wiring as an antenna. I can also see the arcing and sparking of brushes in universal motors being a source of electrical interference.

As far as Faraday cages go, they will shield against electric fields but are totally useless if the interference is magnetic. In that case, you need to be building mu-metal shields.

Bill

Re: Getting a Pacemaker next Monday

#7

Re: I saw a letter to the editor

Charlie Anderson

in the American Woodturner where a question was being asked 'how do others handle this?' as he was getting a runaround from his dr and Boston Scientific

I don't know if he got any answers. The letter was in the April 2012 issue on page 15.

Mars (the letter writer) was my boss way back in 1976.

Re: Getting a Pacemaker next Monday

#8

Jerry Louden

Re: Getting a Pacemaker next Monday

Jerry Louden

Thanks guys. Lots of things to think about.

J

Re: Getting a Pacemaker next Monday

#9

Re: Getting a Pacemaker next Monday

Pete in Holland MI

Might be time to convert your lathe back to line-shaft drive ! : )

Pete

Re: Getting a Pacemaker next Monday

#10

I have a spring pole lathe you can have