Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Pen presses

Posts

Pen presses

#1

Pen presses

Craig Daymon

I found a book on pen turning recently while opening old boxes, "Pens from the Wood Lathe" by Dick Sing. I think it might have been included as part of a JET mini promotion.

The press he uses in the book is not a typical pen press. It is a manual arbor press fitted with a small wooden table and, i'm guessing, delrin plastic head piece, possibly with an indent. There are no clear/complete pictures of the press.

This is certainly a more substantial press than your typical pen press, with a half ton capacity, though requiring some minor mods. Enco sells them for $40.26 for the 1/2 ton, model #805-1005 and, currently on sale, the 1 ton, model #805-1010 for $39.95 (normally $60.40).

Anybody using one of these for pressing pens? Pros/cons?

Thanks,

Craig

P.S. The link below is to the sale, since the sale price isn't listed on the regular page. I'd use the link option, but that isn't available until after I type in my password.

http://www.use-enco.com/CGI/INSRIT?PMAKA=805-1010&PMPXNO=949902&PARTPG=INLMK32

Re: Pen presses

#2

My Arbor Press Mod

John Kaner


Craig, this is my Grizzly 1/2 ton arbor press I got in 1998. I was using a press block and my woodworking vise. This is so much easier. Corian was used to cushion and I made a new press table. The ram can go completely through the table. The 1/4" hole is for pressing out slimline transmissions.

I would go with the 1 ton due to more travel and you won't need to build a base as I did...

Hope this is helpful.

I've loss track of how many pens I created. SWMBO said it's bad when they recognize your voice when you order pen kits...

Re: Pen presses

#3

Re: My Arbor Press Mod

Joe Herrmann

I used my drill press for years to assemble pens. I put a hex head bolt in the chuck and put the assembly between it and the table to assemble the various parts. It worked great and I had no problems.

Re: Pen presses

#4

Re: Pen presses

David Walser

Craig,

It's been a long while since I read Dick Sing's book, but I thought that the press he used was a drill press with a delrin head mounted in the drill press' arbor and a purpose built auxiliary table mounted onto the drill press' table. The beauty of this set up is that the auxiliary table had several different "stations" that could be rotated into position under the arbor -- freeing the the user from needing to readjust the length of the press for each stage of the pen assembly process. This would greatly speed up the process of building a lot of pens.

I have two concerns with the press you linked to at Enco. 1st, it's pressing capacity is overkill. The pressure needed to assemble a pen is measured in pounds, not tons. Would a half-ton press make it too easy to push a part in too far? I don't know. I do know you want enough leverage to make the assembly effortless while, at the same time, giving you very fine control of how far you're pressing the parts together. 2nd, I'm concerned about how much room there is between the top and bottom of the press. Some of the larger single-tube pen kits are fairly long and I'm not sure they would fit within the "jaws" of the press.

I have a pen press and seldom use it. I typically make two or three pens at a time. Rather than spend time pulling the pen press out (assuming I'd remember where I put it), it's quicker for me to grab an aluminum bar clamp off the clamp rack. The clamp does a fine job of forcing pen parts together, giving me a good combination of effort and control. If I'm making several pens, it's worth finding the pen press. Otherwise, a bar clamp or my bench vice works just fine.

HTTP

Re: Pen presses

#5

Re: Pen presses

Greg Haugen

I prefer to use the arbor presses for pens. I like that they're vertical and not horizontal, like the normal presses. easier to keep everything in line and less to fumble with, compared to the horizontal style. I've also used the arbor press for other tasks in the shop as well. There are many mods you can do to them. I have the "furniture feet" felt pads on mine, to protect the parts of the pen. Much rather have a "multi-task" tool than a single task tool.

Re: Pen presses

#6

I use my lathe...

GaryG in MD

Works great -- just stick little "jam chucks" of very dense wood in the headstock and tailstock and press the pen together in between. The only trick is being careful to have it properly centered on both ends. A couple of marks take care of that. This gives excellent control because you can crank the tailstock up very slowly and gently to apply only the pressure needed, and it can't overshoot. ...Gary

Re: Pen presses

#7

Re: My Arbor Press Mod

Craig Daymon

John,

Thanks for posting the pics. Unfortunately, they are very small. Could you possibly post some larger images?

Thanks again,

Craig

Re: Pen presses

#8

Re: Pen presses

Craig Daymon

David,

Dick Sing is definitely using an arbor press in this book. I think it's not his only book, so maybe he uses the drill press in another book.

I realize there are several different ways to press together a pen, but the arbor press does have appeal to me. I like the idea that it has more than one use and that it is strong enough to handle some serious tasks. Its rigidity is a definite plus and I also like its vertical orientation.

I personally believe that the power of a press like this would make it easier to smoothly press home the mechanism to the desired depth. It is manually controlled and a regular pen press would be subject to the same possibility of over pressing, possibly even more so as it might jam up where the arbor press wouldn't. Then, given a tendency to push harder when it jams, when it snaps free it would go too far. Guessing, no hard facts here.

Maybe someone should just make some delrin caps on #2 morse tapers to use on the lathe itself? Maybe I'll make a set? I have a 3/16"-10 tap for the Oneway live center and a 1"-8 tap for the headstock. Once in place, it would be easy to cut a centered indent. That would be a quick and easy solution, but the arbor press still has its appeal.

Sorry, just rambling. Obvious why I don't text or twitter, isn't it.

-Craig

-Craig

Re: Pen presses

#9

BarbS

Here's a set

BarbS

I didn't want to invest in a press after buying all the necessities to make pens, so I turned two M2 tapers for the Jet mini, drilled out an inset and epoxied in a wide disk of UHMW plastic (from the Lee Valley grab bag they sold, a while ago?) I thought it may be too soft, but it's working well. If it gets ragged I can turn it down further, and if it wears too quickly I can always turn it away and just use the hard maple itself. I really like being able to slowly close in the press action with the tail stock.



Re: Pen presses

#10

Hope this is better...

John Kaner


Having resizing issue. Was happier with XP then this 7 version...

Re: Pen presses

#11

Mike Stafford

Re: Pen presses

Mike Stafford

When I was turning a lot of pens I used my bench vise for assembly. It worked great. I even made some go/no go block that fit across the two faces so that as I pressed the transmission into the tubes it was set to the proper depth.

I didn't ever have a problem with alignment using this arrangement.

Re: Pen presses

#12

Re: Pen presses

Don Evans

I did the same thing as Mike. I made simple gauge by gluing two 1/2" wide maple 90 deg glued together. No fancy miters at the corner just one edge against the other piece. Start the mechanism into pen by hand, lay it in the "V" gauge and press it together with bench vise. I sized the length so it would press to proper point and then stop the vise from going further.

Also have a press as pictured above and used same "V" in it.

Have also used drill press but I like the bench vise best as it is easy to hold the "V" in it with left hand and operate vise with right. Wood plates attached to the vise protected the pen's. Used UHMC in the bench press for protection.

Don

Re: Pen presses

#13

Steven Antonucci

When I made pens, I just used a bench vise?

steven antonucci

Never had a problem?

Am I missing something?

Steve

Re: Pen presses

#14

Mike Stafford

Re: When I made pens, I just used a bench vise?

Mike Stafford

Yes, Steve, by not buying a special tool you are hurting the economy of a third world country manufacturing this specialty equipment.

The guy who taught me to turn pens used a quick action bar clamp (the squeeze the trigger kind) to assemble his pens. It worked like a charm. He had V-notched pieces of wood cut to length into which he laid the parts and squeezed the clamp until the transmission was set to the correct depth.

Re: Pen presses

#15

Drill Press with a piece of dowel


Re: Pen presses

#16

Re: Pen presses

Greg Haugen

Mike's and Steven's use of the "v" blocks is a great idea and works great. I've used that style of jig especially on large quantity projects, like "pens for troops". Almost anything that has the ability to press would work for pens. I, personally, don't care for the conventional "pen presses". Most of them aren't big enough for the use of the "v" blocks, their single task, and pricey. Craft Supplies used to have a headstock and tailstock accessories for pressing as well, not sure if they still do or not. I started to use a arbor press after talking with Arizona Silhouette. I was placing an order with them and asked why they don't carry any presses, and they're answer was simple, we don't like them and recommend arbor presses or other options.

Mike also brings up another point, is the origin of manufacture. I do wish pen turning wasn't almost completely "made in.......(fill in with whatever area of Asia)". I've only seen a couple of pen kits that were made in North America, let alone the USA.

Re: Pen presses

#17

Re: Pen presses

Rich Egan

Greg:

I've never assembled a pen kit, but I bet I could make my reloading press work. It would have plenty of leverage.

Rich

Re: Pen presses

#18

Steven Antonucci

That's what I am here for!


Re: Pen presses

#19

Steven Antonucci

What V block?

steven antonucci

Ok, I see that great minds think alike, but I cannot see what you might have used the v block for?

I just put things together "close" and squeezed? For seating the ink cartridges, I stopped to assess if I was in far enough, and if not, squeezed it a little harder. After a few dozen pens, you kind of know when to stop?

Steve